Video

Just a heads up to anyone watching this still… you’ll have to either connect it to your high beams, fog lights, headlights, daytime lights or install a toggle switch. They’ll continue drawing power from your battery with your vehicle turned off. It took a couple months but they eventually drained my battery. Didn’t suspect the light bar since only the tiny red led stays on but after my battery died several times, I finally disconnected my light bar. My battery hasn’t drained since, so I’ll be hooking it up to head lights. The light bar will still remain off until you turn them on with the remote but this way, your battery will keep its charge after you turn off your ignition.

Best install video for these I’ve seen. Much appreciated!

Oooooh the wire nuts nooo use quick splice connectors and butt connectors oooh it’s not pretty wiring anymore fellas

Sorry it took me a bit to get the vine review uploaded, hopefully it still goes through and posts 😓 had a car wreck over Christmas, had to apply it to the new jk instead

Should of used heat wraps for the wiring

How the hell did you get the blades off? Mine were stuck like yours ;-(

Does the relay need to be grounded?

Bad U-Joint in the Drive Shaft. Cant just replace the U-Joint, Subaru makes you replace the entire Drive Shaft.

You ever figure it out ?

lol we’re all stuck in this issue or what? i have a similar issue and could’ve swore it was the clutch and i’ve replaced the whole clutch with a kit and same issues.. noise is coming from the front end and i’m starting to the ink something with axels or brakes?

Thanks for the video. Helped me out a lot.

Do you got any light reflection in the windshield from the bar?

will those brackets work with a curved bar?

Great video thanks for the run down.

How was the wind noise?

I think is your uppipe heatshield is loose

Where is the button at

So I just got this from Amazon and I tried the door seal method on the fins, and maybe I'm using the wrong weather seal strip because it hums like a mofo. Any tips?

Awesome. Did you experience any rubbing of the metal from the brackets against your paint after months of use at all?

did the weatherseal help with the noise at all?

Yes the Relay needs to be grounded

I just installed this light bar and so far loving it. I noticed the red light on the on and off button is always on. Is this normal or did I do something wrong?

Did the weather stripping g stop the whistle?

Can I use this same kit for a 2002 tj sport?

Does it cause any glare at night?

Good stuff mah gah

What size are the weather wire knots

Mr. This leed is 50 inch or 52 inch ?? My car is jeep wrangler 2004

Anyone find out ?

Bhai mere ko bhi leni hai light bar 52 inch

same on mine lol

Just wanna tell you that this video is still doing wonders in 2020! Thank you so much for making this. Ladies, if you're worried about installing this yourself DONT. If I can do it by myself so can you! Thanks again, this light is still worth ALL the money!

Does the upper part of the mount rub against the paint and are there any issues when opening the door?

Look up heat shrink butt connectors..... lol lot cleaner and slim line ...

U should had cut off all that extra wires for a cleaner look. Also this cars are 12 volts I dnt think u would get 18 volts from the battery 🤔

Did you do anything for the red light when it’s off? So it doesn’t drain the battery

Thanks for sharing :)

my outback has the same noise I dont know what it is .did you find what it was

Same! Anyone find out what it is please post answer

So where did you splice the small lights to the light bar?? At 12:19 I get completely lost trying to figure out where you got the cable you ran from the driver side and the passenger light to connect to the main light bar cable? Do I have to cute a piece of rubber of the cables and splice it like that? PleAse help

i think i live in the same development as you lmao like no joke

I had the same problem. Now my slide pin won't slide smoothly no matter how I clean the chamber, grease, brake clean, bunch of q tips jam in the chamber to clean the shit out of it. It still won't glide as smoothly as the other glide pins. Any tips?

Hey, did you ever get this fixed because i have the same problem right now with my 2005 wrx with clunking noise on a 1st gear take off and 2nd gear also. I would like to know if you got it fixed and what was bad and changed.

I have the same problem lmk if you found out what it is

Hi, we autoparts producer and we are inviting youtubers to do a video review for our Wrangler Headlights and we will provide free sample. Hope to have a chance to cooperate with you. Please let us know what you think.

oil can shoot out by the pin when hot expanding and pin can shoot out like a bullet some say so watch out. if pin chamber is deformed after heating it can be drilled out.

Can you turn on only the small lights, or do you have to have them all on at once?

Just purchased this just because of your video!!! Looking forward to your help when we install! Thank you for taking the time!!

How’s the noise? Does it whistle? Did the weather stripping help