Video

Thank you for such a well detailed video. I'm looking to do this on ny 640i and your video is by far the best

Have you experienced or heard of replacement axels being manufactured with the cv boot being too short causing there to be tension on the axel and in some cases actually pulling it back out of the transmission/transfer case?? Please help

Do you know how many kelvins on original HID f10 LCI model? And there is d1s fitting?

Why we need to put a new bolt ??

Is it possible to do it when car is standing on the wheels? Without taking out the wheels and lifting up the car? And how much time do I need to do it? Thank You for a video.

When u made this video… going stage 2… What all have u done to the car.. All I’ve got is bms intake/catless dp/ muff and res delete

Man I appreciate this video so much

music wasn’t loud enough

One of the better, cleaner installs I’ve seen.

I have a question what’s the super tuning license for ??

After all that could of done seeing how they looked ?

Now whatchu wanna do 😂 Thanks for the vid homie

And you must pay 500 euro. Its expencive

Outstanding video on LCI bulb install! Lotsa work but seems to be worth it. My headlight washers may create more work. I plan to change out my bulbs very soon. Thanks again! 👍

Your welds will rust using 70s6 wire should have used 308 or 309

Great job. Very well explained. Thank you

Any issues with the CEL? Were you able to turn it off?

Finished product looks really clean! Cant wait to give it a shot on the civ and hopefully choose a color that doesnt make her look like a shitbox 😅

Would this work for a 2015 740li?

I cannot take the 18 mm off. Shit is on too tight. Any help?

Why isnt it possible just to fill up what is lost

It's nice to see a newer generation having fun with these cars. Pro tip. Add an H-pipe and it will sound way more balanced, add HP (balanced back pressure) and you won't have the gunshot pops. Unless that's what you were going for. Sounds good guys! Glad to see you are having some fun with the car! :)

May I know why there is a hatch on the fender liner? They put it there to change a light bulb. There is no need to remove the headlight.

Hi, when you replacment front driveshaft is oil leaked ?

Nice job

Um...thats not a "wheel well"... just....sayin.

It’s not necessary to remove the caliper, rotor,dust shield, because the axle does not protrude through the hub, also before tightening the control arm bolt you was suppose to put a load on it to prevent premature wear. Thanks for sharing.

What exhaust setup?

Xdrive has 4 of these or two? Should I just change front two?

Well, i guess you never did do "more videos like this". Did your car get repoed?

The video and info was great but the music, whew

Idk why you have to spray back. Can you spray front while on the car? No taking wheels off?

At the 8:52 mark, "dude this is such a fuckin pain in the ass" 😂 Seriously. Working with that caliper tool is neat in theory but definitely sucks in practice.

How long should it take a garage to do this?

My whole rotor and shit spins so I can't tighten the stupid cv axle bolt even with brakes applied glad everyone has it easy

Since the video was aired, April 2019, how is the paint holding up?

Awesome thanks...going to try this on my Tundra

Do you get a code afterwords?

So we’re connecting aluminum to plastic? The aluminum charge pipe does ny connect all the way to the intercooler ?

Great video

Did you have to loose up the exhaust after the cat converter for removal of the DP? also did the complete intake airbox has to be removed for 02 sensor wires? About to do this project…thanks in advance!!!

Really good video thanks, it helps with the G30 too.

Any axle shaft seal replacement?

How long did it hold up cause I was gonna think about doing that

yo what clear coat did you use?

Looks good but personally the song just ruined it, especially when you tried to talk over it. No music when you're giving instructions, better yet no music at all!

Can I use MHD by only buying the Flasher License and the OBD2 Adapter, or do I need the Map to tune my car?

This was a great vid. Extremely detailed. Top tier bro!

Looks awesome! How did it hold with time?

All is good except for one mistake you did. You cannot tighten the thrust arm without loading the suspension. After installing everything and torquing the axle bolt, place a jack under the brake disc and raise it up (you are compressing the spring) as if the car is sitting on its weight. Now torque the thrust arm. Not doing that will eventually damage your thrust arm bushing. Other than that, all is excellent work. Thank you