Video

I love how you go step by with your video now I understand

Use flux and low melt solder.

This is actually way trickier than I thought. I've managed to wreck one replacement port already. How to get solder to adhere to the holding "legs" by ensuring they're hot enough WITHOUT melting the plastic inside the port?! You made it look so easy!

Ebike applications 👍🏽⚡️

Micro USB ports are total design fail...

For god sake, get your self something smaller, even a t245 would be better. Ideally for this size you should work with t210 or even t115

I have a problem with one of my old phones. The Alcatel OT-665A. The charging port is loose & it came off. So how can I make it work again? 🤔

what temp and airflow bro??

big thank you

I'm doing this after one month of training at work! I'm super excited. I'm glad I'm extremely nearsighted. It helps a lot with these ridiculously tiny components.

nice fingernails!

hello, what is the best temp in °c for this exercise ? i think 450?

You should use flux ..and cap tape ...you have many small components near ...it's not indicated your method...good luck

is it the flux that holds the part in place? When I try to do it, the parts move all over the place and I have a big project coming up that has a couple hundred 0402 components and I don't think I want to hand solder all of them if there's a better way!

If I was to send you a small board with a few parts that need reflowed , would you ?

This video gives me hope. I always thought I couldn't solder cause I have slightly shaky hands. But it's just bad technic with no flux. I've learned so much with these videos.

New subscriber here. That's a good way of showing different video angles. Thank you.

Thank you for this information. Can you write the name of the large battery?

⭐️⭐️⭐️⭐️⭐️- If a 5 star rating were to ever mean anything. All 5 would be yours. You & this video here are by far the best instruction video I've seen heard & understood completely the first time. Thank you kindly 👍🏆🥇

When I tried this on a broken Samsung galaxy J5, it blew off all these tiny parts next to the port.🫣

Would be nice to actually see them in action

Sir I wonder if you can please help me I’m disabled and I wanted to know do you have your own company that I can contact for some work done for some medical equipment that I have. How much do you charge and do you have a website that I can go to thank you.

Great video. You saved me a lot of work and money.

czcams.com/video/kGiOdimzHDM/video.htmlfeature=shared

Thats a clean board, did you design it?

Is the 60$ Hot Air/Solder Combo link from the description correct? Or has the price changed that much in two years? :D

Good job, well done. Is there any possibility to check the connexion between the chip termlnals and the different pads before putting it to work?

How you do that, iam heating since 1h nothing happened

You finger blocks the view couldn't see jack

1:27 you blew off one smd resistor from the board

I have a question about the battery pack and cool white led string. How do I contact you for a quick question?

I thought it would be difficult. I have to get the flux i have a heat gun so that should suffice. Thanks good vid

today I lifted my table while a kvm switch was in a bad position between the moving desk and wall, and yanked the micro USB port off the circuit board. Wondering if this is a better solution to purchasing new. I don't have the tools so might be better off replacing :( Thanks for video either way

Does the port have to be the exact same for the replacement? I can’t find the micro usb female port that’s exactly like the one I need replaced.

You don't renew benith the ic

Are there any led short-strip lights with a very small battery case? Thinking to install LED behind a small wall installation but there are no power outlets close so want smth on batteries that can all hide behind this installation

hi there- great video , thanks so much. Quick question- for running 2 led strips( 5m and 2m) could I run off 1 battery pack by using a USB adaptor that allows me to use 2 usb's in one port.

Our big goofy fingers look so clunky under any type of magnification. You feel like you are being delicate and gentle then you see how jerky and sloppy your motions are. I always think "Do I really shake that much?"

Thanks so much this helped a lot

This was an AWWSOME video. Thank you for making it

Can I remove thr microusb and replace it with usb c?

I'm about to reflow a QFN and 0402 chips. Just watched and got some feelings about it. Thanks.

What was the temp of your iron to solder the 0402 parts?

Hey great video! Question for you, if I want to buy that battery pack, but I want motion sensored LED strips, what is the best led strip to buy?

Hello. Great video. I’m looking at running 2 separate runs of 5 meters long of water proof strip lights. Would it be better to run two power packs? Will I get more run time the bigger the power pack? Thanks.

There is no link….what are the names and power of the packs

The board I have has lost the solder in the surface mount pin slots so the micro usb port can’t make a connection, is there way to fill those slots back up with solder?

I don't know why there is solder mask on the bottom exposed pad footprint. That proably makes it more difficult to solder properly.

CouldI use a hairdryer as a heat gun?

I didnt know this could be done at home. Well done!