![JSTSEND](/img/default-banner.jpg)
- 9
- 21 136
JSTSEND
Registrace 30. 07. 2014
NB Miata at Laguna Seca
First time at laguna driving
2002 miata
Stock motor
Intake
15x9
205 take off rc1s
ground control coil overs
2002 miata
Stock motor
Intake
15x9
205 take off rc1s
ground control coil overs
zhlédnutí: 48
Video
Trying to keep up with a Turbo Exocet in a Stock Powered Miata Thill West
zhlédnutí 54Před 11 měsíci
Stock engine Ground control coil overs 15x9 Sway bars
Thunderhill west 1:31 2000 Miata
zhlédnutí 46Před rokem
2000 miata bilstein coilovers sway bars alignment stock power k&n intake
Thunderhill West stock miata 1:32
zhlédnutí 204Před rokem
Stock power with a intake Bilstein spec miata take offs Sway bars 15x9 6uls with RRs take offs on their last leg
Rusty 1:26.84 Thunder Hill West nb miata
zhlédnutí 83Před 2 lety
Rusty 1:26.84 Thunder Hill West nb miata
Rusty 1:28:41 Thunderhill West Miata
zhlédnutí 49Před 2 lety
Ran a 1:27 but GoPro died so here’s the next best thing, messed up on turn 3 and kept bogging turn 9 and 10 cuz u didn’t shift to 2nd so could have been better but till next time And it’s a little over exposed lol
Ford E40D Transmission Removal
zhlédnutí 20KPřed 3 lety
Step by step tutorial on how to remove a E40D Transmission out of 1996 F350
Thunder hill West CCW 1:36:46
zhlédnutí 72Před 3 lety
Thunder hill west 1999 NB Miata 100 HP COILOVER TIRES HAWK PADS RBF 600 15x7
Thanks for the video. I need to remove the E4OD from my '97 F-350 Dually because it needs a rebuild, and wanted to see what I was getting myself into. Seeing you do it really helped. One thing that might help other viewers: 2:55 "Something a little bigger than this bucket. . ." When draining the fluid and dropping the pan to change the trans filter on E4ODs with the truck on or close to the ground, I've had really good luck using the black plastic "mixing tub" or "all purpose tub". You can usually find them at home centers for under $10, and they are about 20" x 27" x 6" high.
How the plug come off that’s what hardest not damaging
I wanna be like you when I grow up.
great video. loved the hints along the way. very clear voice, you should do more how to videos on the same truck.
When you switched from 4x4 to a 2wd setup, did you switch to a complete 2wd E40D transmission or were you able to just unbolt the transfer case from the existing 4x4 trans and run a slightly longer driveshaft? I want to do the same thing to test something.
You would have to change the output shaft to a longer one to accommodate the 2wd extension
Looks like that 2ws drive trans can be converted into a 4x4 by swapping out the output shaft
Actually ended up doing that right after I removed the transmission lol
I've been thinking about converting my '97 Dually to 6x6, but from what I've read swapping the output shaft requires disassembling almost the entire transmission to get to the snap ring that retains said output shaft. I'm about to rebuild my trans, so now would be the ideal time while I'm already in there.
Don't you have to completely disassemble the trans to swap input shafts
@@nicholasgerman5376 If you mean the output shaft or "tailshaft", then yes you have to disassemble almost the entire transmission to get to the snap ring that holds it in. That's the shaft I think you mean, because that's the one that's different between rear wheel and 4 wheel drive transmissions.
That rig has a transfer case?
4WD does
Do you have to put your trans in neutral?
Pulled this in park
Thought he said it was a 4 wheel drive...? Transfer case must be under the seat....
WAS 4wd lol converted to 2 for a couple days to test something
I fell asleep listening to you bud.
Guy makes a helpful video and you sit there and try to spread hate your a sad human being i pity you truly
had Covid at the time bud.
How do you like the transmission jack I got the same have not used it yet ,,,,is there a vent on the trasmission,mine was leaking fluid now it’s not might have been filled to capacity however a aftermarket transmission cooler was installed thinking it’s smaller then stock ?
The passenger 2nd from the bottom bell house bolt was it a problem when pulling? Getting ready to pull mine and the thing is out but not removed cause the exhaust.
Just loosen it and let it sit in the hole, you cant remove the screw till the whole tranny drops
@@jstsend6020 Thank you...I have a 97 E350.. Couple of questions... 1. I read a write about upgrading their torque converter to the 6.0 diesel 2.. have you done a shift kit or any other improvement mods
2wd in a 4wd
Just for a few weeks now it has the 4wd trans in it again !
Hey man how did you know it was the torque converter that is bad ? Because I think mine is bad my 1997 f250 7.3 started flashing the over drive and stopped
OD Light flashing identifies you have a transmission code! You need a special code reader to read trans codes
@@jstsend6020 Thank you for this. I’ve got a 97 F-450 and it’s suddenly leaking from the fly wheel inspection port. What did you find out about yours? No shifting problems for me just leaking like a stuck hog. Either the pump seal Torque converter seal or the input shaft seal because it’s obviously leaking past the bell housing to fly wheel inspection port
@@sterlingyoung88 ours was a broken pump seal ! It was water falling out oil when running
@@jstsend6020 If you took it to a shop could you tell me the price that they charged you I’m very mechanically friendly I’ve never taken my truck anywhere and this will be the first time I will have to contract out this issue thank you for the quick response
@@sterlingyoung88 1800 full rebuild of trans