Video

Heller Passage

Dickens Flats

Marisa Prairie

Marisol Street

Vicente Trace

Almost as bad as the instructions! 🤣

Mine display "LLL". Any idea why?

Good video and explanation, thanks

thank you

Trapas

come si accende

Please how can I set my pewelly

Give me your phone 📱 number

Give me your phone number

Wampaye nimero yawe nkaguhamagara

hello great video, do you know if it is possible to set both outputs to heat? or does out 1 heat and out 2 cool?

нефига не видно и не всё понятно...

crap video.. it's not a speedometer it's a tachometer .. 😡😡

How to pairing Antusi A6 with remote : Firstly : To clear the previous remote control, press the BLUE button for 7 seconds (keep pressing until you hear second BEEP, about 7 seconds pressing). Secondly : Press the BLUE button for 2 seconds, the alarm sounds (first BEEP), then and press and hold any button on the remote control until you hear BEEP again. Finish. Test your remote. It's work for me, hope this procedure will help.

Do you or does anyone else know if the "high-temperature alarm" can be switched to be used as a LOW-temperature alarm instead?

Thanks, I just got one of these and I would have trouble with the settings without your guidance.

do you still have the manual bro?

You didn't show how to set it up with an actual humidifier and you are afraid to talk

Di beri nama dong om kabel ini buat apa gitu Lo om

the load in the diagram does not make sense to me... the way it is in the picture any load will always get power directly from the 220V source, as both the power wire as well as the load wires will connect to i.e. 1 and 2

Up button is the ON set temp... Down is the OFF set temp.

My measured speed jumps to different values. does anyone know the problem?

It is possible calibrate the temperature of the two probes when the value are wrong?

Hey guys and girls. We need to be clear. Surely, this is a thermostatic "relay" device. So, it has two sets of controls (upper and lower temp switching) each for 2 relays (connecters 7->8, connectors 9->10) (Max. 220V AC to a heater, Max. 220V AC to a fan, connectors numbered 7 and 8, 9 and 10). YOU MUST NOT PUT LIVE AND NEUTRAL INTO THE CONNECTORS. The relay only switches through like a normal single pole light switch! The connectors 1 and 2 (power supply) must be 12V DC (A battery should be enough to power the device, the relays and the LCD display. The connectors 3 and 4 (activating a heating element or fan) will be the low temp sensor, the connectors 5 and 6 will be the high temperature sensor (activating acooling fan or refrigeration unit). This device must only switch a single wire to each unit. CONNECTING both wires (e.g. LIVE AND NEUTRAL) will damage or destroy the device - and presents a fire or electrocution hazard! It would be great to hear back from people to either confirm or deny my analysis. Thank you.

Will this controller plug into 220 AC to temperature switch and control a 12v 100w ceramic motorhome heater? Thanks very much.

Talk and say what you were doing. This does not help one thing.

Really crazy. Doesn't say a word, and doesn't answer my question either. The DC version doesn't indicate polarity ANYWHERE. A smaller version of this has a plus mark on the terminal with a magic marker. Nuts.

Saya set P1 dan saya teoan bersamaan tombol set dan c/f malah unitnya ngerestart om, knpa ya ?

Receiver and remote how to pair?😌😌😌

For 5 bucks that I payed, I think it was an amazing aquisition😂😂

Eso que es

Hadir bang...mau tnya bang...kalau saja di modif biar bisa pakai tegangan batrey 12volt bisa gak bang...

COMO LIGA OS CABOS?

😮

What a useless video, clicking buttons randomly. Why post crap like this?

Hello, can you also change the sensitivity of the alarm, I have an antusi a6 too, but no one shows it

Calibration instructions are unclear. English instructions also unclear.

Promo_SM

Super

Thanks! Useful tutorial (but I had to slow down the video speed since I'm slow!).

I want to bye 1 Pic controller. Are you arranged it?

كيفية تركيب الاسلاك لدي نفس الجهاز v 12 هل يشتغل علي 220 v

Terrible video, no audio, confusing finger pointing that fails to go in a logical order. Even the diagram in ink is next to impossible to figure out, and that, is when the back of the tacho gives wiring that may be completely wrong.

It's best controller more then stc ??

Hello, in which connection do I have to connect the magnetic brake sensor? because they told me that the yellow and black cabkes and the red one are connected to the red of the accelerator, and it turns out that it sends a signal when it does not brake and the engine does not start, it does it the other way around, how can I change that so that the signal is sent When do I brake? thank you It's for an electric scooter health and freedom for all