Video

I

There is no way I am waiting for the third day, that is NOT the way I role. 3 days is for suckers.

I bought one, it is ok. I took the spring off as it cants the chuck/drill bit towards the shaft with the spring as there is a bit of slop in the sleeves that ride up and down the shafts. I removed the two hard plastic sleaves from the chuck carrier and replaced them with a piece of ultra slippery Teflon PTFE 1/16" thick sheet (McMaster Carr part# 8545K13) that I rolled into a cylinder. To cut the strip uses the full height of the hard plastic insert to measure for the width of the strip and marked a line with a sharpie. Cut the strip off with sharp scissors. Then roll the end of the strip around one of the steel shafts(PTFE is soft) and mark the approximate length needed to make a complete cylinder, you will have to trim off tiny amounts of the length to get it to fit perfectly into the holes in the drill chuck carriage(it should be a tight fit), push the piece of PTFE all the way to the bottom, I needed to use the edge of a 3/8" dowel to to get the PTFE piece to bottom out. There is no need to reinstall the two screw they are not necessary as the Teflon fit it tight. All the slop is gone. Reassemble the drill guide and put a thin film of gun oil, 3 in 1 oil, synthetic motor oil, or the like on the steel shafts, it will be silky smooth and it will be an excellent tool. I would recommend mounting it to a 8" or 10" square base for stability. This is a light duty, hobbyist tool, do not expect to be drilling holes for pegging mortice and tenon joints in huge timbers.

Great video thank you! Got about 8 hinges to do original 1930's ones 😬

1 foot by 24 inches. :-)

what kind of rope is on the OG Clew?

Very easy girl sample makita

Aami nimbu ki kore

When you attach the table top to the apron, how do you line them up with apron under the table top? And do you pre-drill the holes in the apron?

Can you do this with mule tape?

Great joint

Will this work with lead based paint?

Thanks!

Thank you!

This was really helpful! I want to make a magnetic wall in my daughters playroom and make some wooden gears with magnets on the back, various other things for ger to play with. Im thinking for my application maybe sheet metal would be better.

For my purpose, I think this paint will work perfectly. I’m building a slot car track with some pretty big elevation changes. I’m going to use this paint to give me better downforce in some of the more intense curves. (One of which mimics Laguna Seca’s world famous Corkscrew.) As it is, the roughly 3/16” rails are the only source of magnatraction in those areas and you can lose control VERY easily. My plan is to paint a 1”strip just inside & outside of the rails of my slot car track. The second coat will be 3/4” and the third will be 1/2”. I’m hoping to give a smoother, more controllable drift in those particularly tricky areas of the track. This review was extremely helpful, THANKS!

Çok teşekkürler en ayrıntılı ve açık anlatan sizsiniz

awesome visuals! thank you for the great explanation

just found this today (2024) and still very helpful and loved the video! 🎉

I hate that the fence bracket is proud of the table top. That means work pieces fall down to the table after clearing the fence bracket. What were they thinking? I bought mine when they were transitioning to the newer (cost reduced?) model. I specifically chose the older model because it seemed to be built better. The blade wobbles when first turned on. So don't put the fence too close to the blade. Otherwise the blade will scrape the side of the fence -- don't ask me why I know.

Nice! Thanks for the tip. It’s so simple yet effective.

What's the best way to dispose of the water? I live in an old house and may be dealing with lead paint. 😬

can baking power do the job too?

Excellent, I really appreciate these kind of videos. Thank you very much, sir.

Wow very creative

Спасибо🙏💕😊❤

Bake a teacake, take it to your neighbours, ask them to help you lift it. Three people and a second borrowed ladder will make short work of the lifting, and then you aren't stuck with about 8 metres of chain that you now have no use for.

terrible presentation on a good product

Great explanation

Thank you for this tutorial! After the repair should the cord be restricted to indoor use, or is is still appropriate for exterior use? I have a couple of previous heavy duty outdoor use cords I would like to repair, but that new connector doesn't appear it would block moisture, or would it? TIA for any further clarification you can add. 🤔🤔🤔

But you should compare krylon Spray to Krylon CAN.....you don t have "control"..... so your results are not reliable

well done Nate, thanks :D

I lost the remote... it should work without remote right? mine wont run with the buttons on the unit. fuse maybe? Not my circuit breaker. Thanks

Could I use this on see through polycarbonate sheet?

Super,beginner friendly. Thanks

I hate the fence on this saw. So hard to get a straight cut. Thanks for your suggestions to fix this.

Thanks for the advice!

Good down to earth 😅 information.thanks

When I watch your videos I also pine for the bulk of a larger one

brushless motors are very efficient. you explained it wrong. the circuit needed for it is where all the difference. circuit is not for maintaining power rather it is the one who gives the power to start with.

Very inteligent and interesting way to explain something that can be very confusing for most. The visuals removes all doubts. Thank you!

would it work on high water exposure area, ie next to shower

Thanks 👏👏no rocket…

Thank you for the straight forward video, the ground on the washer broke and I really don’t want to buy a new washer !!

thanks man that was very helpful.......

It’s very precious when handmade 😊🥰☺️

Sockets do come with holders you know .

😂

Thank you! Very well done video!

Acetone..wow..nice video