Video

I want to build one like this,i have no steel material..thank you for sharing this wooden belt sander,now i can make it now thank you so so much Sir,very very good idea 👏👏👏👏👍👍👍

Rosmira

muito bom grande profissional

Beautiful work, Paulo! Really well done! 😃 Stay safe there with your family! 🖖😊

Very nice design.

What type of make and model is that planer I might be wanting to get one for myself

Really beautiful work, Paulo! Nicely done! 😃 It's great to see you back! Stay safe there with your family! 🖖😊

Was wondering if you use a chemical to remove all the old finish or mechanical means? I’ve got a 19th century grandfather clock with a similar crack in the base part of the case. Hoping to restore the whole clock and not sure yet whether I’ll be able to close the crack via glue and clamp or to fit a tiny long wedge of similar material then sand. Might like to consult with someone on your team and possibly pay for advice or services. Thx.

Why were you using the card scraper on the bottom of the plane fro about 1/2 on both ends.

Bravo 👏

Hello, respected professor, thank you for sharing the useful work, I have seen most of this kind of work in videos, but the work of making this loading device is much more basic and I don't think this part is the only part, you must have shared it from the beginning of the work. Please post all the parts of this type of device and explain, for example, part 1 and part 2, etc. It would be very kind if you could do it, thank you very much.

Me gustaría ese cuánto cuesta

Very nice build. One of the best designs I have seen for a wood build. Did you have trouble with the skate wheels holding up. The bearings rather. I built one a bit before you did from metal. One of two videos on my channel, but I could not keep bearings in them. I did and do use mine a lot. Man they are far more handy than one would think. I could not imagine not having it around. I finally bought a real set of wheels for it. My drive wheel is made of oak. But It is a smooth little machine. I am wanting to do another with a tilt a lot like the house made one.

Get a belt dresser for that edge sander. It would save you a fortune. Never go uphill with an edge sander, but I think you learned that lesson in the out take bit. Great video and a lot better than using an angle grinder which is far too fast.

I haave jest realized that I don't have the belt to run the runner rollers from the motor.... lol thanks

Am I missing something? Surely the point of a flip stop is that you use it flipped down to set the workpiece in the right position, but then flip it up to make the cut, so the workpiece doesn’t get pinched between the blade and the stop block. I love the design and I’ll be making it, but I think you’re missing the point of a flip stop rather than a fixed one 😊

Lovely board. Can I ask what the oil is please?

Hi what kinde of angels it need to have

Nice.

Exlant jab sir 👍👍👍👍

Plans?

😅😅😅😅😅

Не хватает клейма!

Бесполезная приспособа, современные диски имеют резцы с попеременным уклоном, а не под 90°,

Thanks so much for taking the trouble to post this. Really helped me.

You’ve built quite a number of machines!

That jointer is a BEAST!

To save on cutting disks cut 1/2 way through on the wide side and elevate one end cut side down and smack it with a sledge hammer on the back side of the cut. it will break at the cut line.

Плохо

Belíssimo trabalho, Paulo! Ficou excelente! 😃 Dá até pra colocar um tablet, pra ver receitas enquanto você cozinha... Desculpa, é que tô com fome! 😂 Abraços e se mantenha seguro aí com sua família! 🖖😊

Beautiful work. I'd pay good money for those. The love that was up into it is obvious. This video was so calming. No talking, just working.

I hope you credit Ryan Drapela's design of the ManStand. (Also found at CuttingItClose CZcams channel.) Very clearly you were inspired by his design.

Наклон зуба в одну сторону точил? Все зубья? Или через один? Или не все показал?

... sehr schön!

I remember when you built that sander years ago, great job. I am going to look it up and watch it again.

that was totally cool. ThankQ

Unfortunately I would have better access to a plane blade than a truck spring. Not like they're laying around all over.

Thanks! Beautiful wood! That Milor is from another era, what a machine!!!

Beautiful job, beautiful wood and elegant design. Fantastic.

Bom trabalho!!!

Придурок , для начала покажи что потом как делать , чтобы не жрать у людей время

Just wondering if you still have all your fingers? Silly putting them that close to a table saw blade. That's the reason for push sticks!

Hello, what material did you use to wrap the traction rollers?

Wow, those are really nice apple boxes!

gostei muito da tualixadeira 🙏🙏🙏🙏🙏👁👁✌✌👏👏✌

Great

What's up little guy

How's the multi-piece construct holding together after removing the blade several times?

that was beautiful 🙂

I haven't made anything out of mahogany in 40 years. I miss it, it's beautiful wood.