Video

hi, im a fan from philippines. Do you sell tools like this to your subcribers?😊

Is the E Clutch and antikickback function the same?

Don't drink an CZcams.

I found an easier way to remove chuck: I put a vicegrip on bottom of chuck and hitted down with a hammer a few times and came off within a couple minutes. Descubri una forma mucho mas facil y rapida de quitar el broquero: puse unas pinzas vicegrip en la parte de abajo del broquero y le pegue varias veces con un martillo hacia abajo y salio en menos de 2 minutos.

Dude… you put it on backwards. push grinder forwards to cut. that’s why you thought the knob was placed wrongly in the way of the tool.

The problem is that the yellow is all over the place. Yellow Stanley tools, okay since you can all hide them in boxes. But come on not the boxes themselves. No professional design workshop, fancy garage or designer can allow their workplace to look like a warehouse. Make them GRAY or something clean looking. Those companies underestimage the importance of corporate image, and the need of creators of an empty and sterile, and neutral looking environnent.

Stanley owns lots of firms including...da da DeWalt...

Should have pushed the front/shoe of the saw into the wood to prevent the wood and saw from vibrating that much, and also to achieve a quicker cut. Otherwise I hope you’re doing well seeing as you haven’t uploaded anything in a few years, you’re a really fun guy to watch!

What language does he speak at? It doesnt seem to be english.

😅

God I’ve lost the will to live with this video

Thanks for posting this video,I’ve watched it before when I did a plug swap on a grinder,I bought a pressure washer that is 120v 🫣 I’m going to fit the same plug on it later today as I’ve got a 110 transformer the same as yours,it comes with the same type of two pinned thing,wish me luck 🥳

Will it work on milwaukee

RIP

Milton!!! Oh Milton!!! Where are You????????????

you guys think he has a milwake shrine hidden in his bedroom closet ?

This was more of a test of the bit itself, not the drill

Thorough hands on review. Thank you sir

For other users, if you move the handle complelty upwards. You can rotate the handle without drill section moving. In this video it looked like it one piece, which it is not

I think i read somewhere, the thicker part is actually for an impact driver. This tool smoked most tools in the video from ProjectFarm. He showed multiple brands and beat the shizzle out of them

You have the patience of Job!

You did a great job with this video. Im buying. The Dewalt !

Where did You go Milton? Haven’t heard from You in awhile?? Hope you're Ok.

Old thread, but I'm running into problems with removing the bit (not the Philips that it came with.) I'm trying to not break it. Also, I don't think this will work well with "tap" mode, as that's another type of clutch. It's calibrated, or designed to have high torque input, and it will engage the clutch down to whatever they think is optimal for seating screws. Awesome video

Bosch with drywall it does not look like something I would realistically try to big!

Great video. You actually show the thing in use which is good to see. I'm not really bothered about just an unboxing which is what others show. Cheers, will get one and give it a go.

Milwaukee and dewalt bits no movement 😅

That grinder is fitted on the wrong way, and should be at the rear opposite the height adjustment knob on the left hand side facing towards the direction marker. Whilst the dust extraction is leaning to the right hand side. Using the spacer is on the instructions, as it keeps the blade centrally to the dust cover. And you push it forward to contain dust and cut, whereas to the rear is forcing that blade into opposite cutting and burning it out, just like a circular saw would if you went back instead of forward! Think you need to make another video, as this is shit advice on an item that has worked well for me over the past couple of years, and I've upgraded it now to an aidelife cover which is more plastic but better still.

There is a dude on CZcams managed to do it if I can find the video again I will post it

Just picked one up for £50

Ty mate for the twist step....I couldn't figure out how the heck to clip this into location. Seems like the dust port is super in the wrong position, but then you just spin it round. TY!!

Used this with the surface grinder handle and a cheap dust cyclone to strip layers of paint off old render...perfect .

speed: 1100 rpm.. i assume that's off by a factor of 10 :)

What about now getting it off? ( Is it going to be easy or is it now too tight to remove )

Your landlord is going to be pissed.

Great video. I loved the way you took us through the entire setup. It reminds me of me every time I get a new tool that has to be adjusted. It usually takes me 3 times longer to do the setup than to do the work. Anyway, well done. Loved the disappearing act at the end. Bravo!

Like watching a retard get outta here

Hi can it cut pvc cable duct?? Thanks

Thanks for review. They're pushing the other systems here in USA. This seems very portable to unlatch to go up stairs, then you can link together and roll down to the apartments or home where you are working. The Milwaukee as well as other brands are just silly for 1 guy to carry when they are loaded with tools.

I’ve written to DEWALT to TRY and get the correct part number…those dummies don’t understand their own products

It is not a good machine , Poor torque , fiddly settings and today it bellowed out blue smoke and came to an embarrassing halt on the building site. Never had this experience with any other drill .

I heard European clocks turned counter clockwise. 🤪

Bro! Make more vids

Just picked this up for a big project coming up. great they include a bit in each box. Thank you for the video sir

Just got the slides Jamed half way in .How can I get them back out

It also depends on the bit and battery power.

This is great.

Hello everyone. I want to take the time to say thank you all for enjoying my dads videos haha he was so informative when it came to all this but i really appreciate all the love and laughs you have given this man ! But sadly on the 30th December 2023 my dad passed away. We will not be shutting down his youtube as you guys as a community have enjoyed the videos, again i cannot thank you lot for showing all the love and support for this crazy man ❤️

Dude, you don't load DeWalt tool boxes with Makita tools....This is blasphemy and there is a special place for you in technician's hell