Video

do u have a video of how to install the belt for the power flow?

Thank you for your clear demonstration. I agree with the other posts that this is an excellent video. Over the winter I bought a new JD 2032R and immediately removed the backhoe to install my rear mount snowthrower. It’s time to do some backhoe projects. When following the manual’s attachment instructions I hit a wall. The key point in your video that I wasn’t doing is to make sure the backhoe frame is level and a few inches off the ground and to connect the tractor hydraulic lines temporarily to accomplish this. Once I did this everything went flawlessly. This backhoe attachment system is much improved over my 1991 JD855, which I sold when I bought the 2032R. Thanks again for providing this most useful video for those of us fortunate enough to own this remarkable piece of equipment.

The left side is tricky yet ignored?

Hi, how can we contact you for business inquiry?

Good video but I can't see what your doing

Como posso comprar um braço escavador pra esse trator ?

Super 👍

Thank you so much for this sir could you do a video on how to put the snow plow on

Ugh. Deere put so little effort into this. My x540 from 2008 same hopper same power flow . Is easier to install and remove the hopper w no 3 pt.

can you do a blade install vid on the reverse procedure,i am stuck on mounting the blade hardware,ty

What to do if your tool will not turn the bolt to raise or lower the deck. Seems like the bolt on my X350 is frozen.

Need the installation video for this blade. Can not seem to find a video showing how to install it.

Edit -- I case it helps someone else who has all the parts unassembled. I found out the hole in the arms isn't the same distance from each end, it has a long and short end. Short end goes toward the back of the tractor, with the welded seams turned inward. Once you figure that out it eliminates a bunch of potential problems.

I couldn't find an install video to save my life but this video helped a lot even though it was inn reverse thanks.

What is the model for the blower the number ?

Gotta commend your camera person for not showing us a fuckin thing

Do you have to drill holes for the hanger bracket that holds the power flow stabilizer rod? I have the 60d deck it has two square holes that are vertical from one another.

Always great information love the videos. I have a 1023E so when I remove the cutting deck for winter, the lever that raises and lowers the deck, raise the rear hitch? And is there a lock out valve to hold that hitch in the position, thanks for great video.

Hi I have a 1025r 2018 can I do the same thing with my backhoe it did come factory what was differently how to remove my backhoe this seems to be a much easier way to do things .

When you raise and lower the mower deck, does it affect the rear bagger? Does that move? Great video thank you so much for your time.

so helpful and easy. Thanks.

What year is your tractor? Is it before 2016 or after 2016? Thanks

Can I get a pic of where the bracket goes that the blade attaches to. The bracket goes in place of the deck.

This was extremely helpful. I don't live anywhere near you, but I am grateful for the demonstration.

Ugh not happy that we need to remove the frame and everything on the rear and then completely reattach the imatch hitch - kind of makes the imatch pointless if you want to use this device. :P

Is there an in line fuel filter on the 825m?

You didn't show how to adjust the front. Just something about you'll a 18mm wrench.

Just discovered my deck wasn’t setup right EVEN REMOTELY by the dealer (not you guys) when I went to level my deck. So friggin disappointing. Thanks for the video, though! Extremely hopeful. This would explain why my grass was getting cut super short even at “3.25”, which was probably closer to 2.25” in actuality.

I want to smash my head against the ground and kick puppies trying to install this thing on the tractor every time

Thanks!

My blades are not engaging I did everything u said your video was amazing

I watched three vid clips on the 3-Point Hitch Installation and this explanation is by far the best. Great lighting, clear explanation and easy to follow. Thank you for the help.

Trying to follow your video for removal of mower deck; however, height adjustment dial is frozen. Any suggestions for getting the dial freed up?

And make sure Deere has the parts together correctly. Took me 3 times with the box blade tilting before i realized the right arm had the long side toward the tractor instead of the short end. IE: the sway link bolt hole is NOT exactly ion the center.

Thanks for the video. It clearly showed me what I needed to know to get the pro to raise and lower. Simple, but not so much when you don't know what you're doing. Thanks, again.

Hi, would be very helpful if you told me if there is a adjustment for the speed the 3point hitch gose down to fast..thx

I’m having the same issue just installing this. Trying to reverse engineer the process but not enough details for which parts go where. Please provide video or a link where I can go to find installation instructions for an X 380

I saw somebody had posted they could not figure out where to find the installation video instructions etc. for installing that exact blade. I’ve tried to watch it and reverse engineer it but there’s not enough details to do that. Please contact me to direct me or provide video or anything else on how to install this blade

Well done. Thanks.

Perfect and clear, my neighbor just got one dropped off with no instructions so now I can show him, Thanks!

you really should delete this video and do another one with the bucket raised a bit so it doesn't hit the deck in backing off.

This is a great video. Could you make on the 260 backhoe installation? We struggled with one at the dealer, and I figured there must be an easier way to get it alligned.

I have a X330 and want to purchase this exact setup.. Do you have part numbers specifically for the x330 for the blade, bracket and whatever else I would need?

This is a good video but I need to see one on how to install a 44-inch blade on an x330. I am having a hell of a hard time trying to install it. Could you please do a video that can walk me through it.

interesting. I just bought a blade on the secondary market. It's a John Deere blade. I even had my local dealer check the serial number on the blade to make sure it fit a 330. I haven't tried to install yet because I was doing some research and mine doesn't have the same setup at all that yours has.

Helpful for a new X350 owner

What about putting a pen in the PTO

Superb job Adam!

Would be better with close ups. Can't see much with the person in the way

Thanks for this great demonstration. I plan on detaching the backhoe for a few weeks while I utilize a post hole digger. What happens to the hydraulics of the backhoe if it sits for a while, do I need to put blocking under the unit? Will the stabilizers begin to retract, will the bucket curl up over time? the backhoes attachment is about 700 pounds.