Video

Thank you so much for this video! I struggled with trying to get the canopy off for a longgg time.

How did you take off the control panel?

Perfect, thanks!

I just had to remove my boots to install them and I was seriously shocked how CHEAP with the grease they were. I bet that’s why most of them fail

Very basic and very good explanation. Thank you

Dq

In the future, once you get the crank out, you might want to both spray brake cleaner into all of the bearings and then blow them out out with compressed air. Then you test each bearing by free spinning it using either compressed air or your finger, and then you listen for how much rattle you get. Any rattle means the bearing is worn and may not have that much life left. Since replacing the 4 end bearings is relatively easy, unless they appear to be new, replace all 4 of them. As for the others, that requires a machine shop and a skilled technician to reassemble the crank and have zero run out. for a 2 cylinder engine, some minor wear in the interior bearings can be tolerated. But replacing the outer bearings is as good investment as you can make in your snowmobile. Also check to see whether you have any connecting rod bounce due to worn bearings. Any bounce then consider having a professional replace all of those bearings at the crank end and might as well have all the other bearings replaced as well. Buying a fully re-manufactured crank is usually the best way to go, as people are trying to unload those old cranks that they put all kinds of time and money into.

I just knew there would be a video on how to fix this! Thanks for posting.

My service suction line on one side is too short to add a piercing connector so how do I know which of the other two lines coming out the compressor side is the suction side? Is the suction line cool to the touch? Thank you.

Thank you so much

See ya down at the moose lodge.

Hallo, ich hatte auch das Problem, dass die Lok nicht die Brücke hochkam. Nachdem ich das Log zerlegt hatte, stellte ich schnell fest, dass die hinteren Räder beim Getriebe kaum Widerstand aufbauten. Ich nahm die Räder vorsichtig mit zwei Schlitzschraubenziehern ab. Zwischen den Rädern und dem Getriebe befinden sich kleine Noppen am Rad, die dafür sorgen sollen, dass bei zu schneller Bewegung der Lok der Schwung nicht auf den Motor übertragen wird. Diese Noppen waren flach. Natürlich wird auch die "Kraft" des Motors darüber an die Räder übertragen. Ich habe sie mit Sekundenkleber verbunden. Problem gelöst.

Bless you for your contribution to society. This was so deeply helpful

Agalo d nuevo

definitely! and getting some into the top of the can works wonders too

Thank you!

Did you figure out the source of your battery charging issue? I'm just curious about that before I feel comfortable with the new pulley size. Thanks for the video!

Good video. Thank you.

Thank you!!!! This helped very much. Cleaning out baby boys car seat

It was really helpful!!!❤

Here's a slow motion version: czcams.com/users/shorts3xQtfDyfMU4

He cheated

Accident.. why that guy stepped out in front of him is beyond me. I know he saw him coming

Helpful. Thank you for posting

Abuse

Used this to fix the camera where the blue ribbon disconnected when it fell. Thank you for showing how to take it apart.

p r o f e s s i o n a l ! h o w d i d y o u g e t s o g o o d ?

I got one of these recently from Amazon I also got a long strip of rubber I forgot what it's actually called but it was rolled up anyway cut a length in the size of the splash guard because when I put down the splash guard Matt whatever there's a gap it doesn't go all the way back against the wall like yours does and it keeps the water off the counter but there is just one problem and I have not found a solution The circle part that goes over the faucet mine's not round like yours mine is a wide oval I don't know kind of like which would see in a bathroom sink It's not tall like that though it's a pretty thin but because it's there and these mats are meant for these things that go where it can go down flat there right there where the sink divides in half washer wish I could share a picture in the comments anyway right there where the sink divides in half it doesn't go black and water builds up underneath there constantly I can't get it to go down flat I tried if I put something heavy down there I thought maybe would weigh it down but the gap is not wide enough for me to send anything heavy on there that would stay and not fall over and break so if anybody's got any idea what I can use please let me know

Wrong tool buddy

Mine fits similar to yours, it works best when the faucet is closer to the wall so that the flaps can lean up against the wall

Did it get rid of the noise? How's it holding up?

Thanks brother. -hulk hulgan

Thank you! That would have taken me all day to do. I love this app just for helping with frustrating things you would never figure out on your own! 😂

Great post ! Thanks!

Who would have known to squeeze it together, you just saved me another half hour of getting frustrated! 😂

Did you get the matching stroller do you have a video on it?

Thank you, thank you so much!!! What a time saver your video was

This is a great idea! So easy! I wonder if it'll work on the Power Wheels Baja Trailster.

Thank You!!

I’m never gonna buy this product again. It’s complete garbage.

Nicely presented. I've thought for a long time that Ploughman should be more read than it is.

Thank you so much for this !!

After 20 min of struggling. I thank thee sir

Love u so much king

The 102mm Tensioner Pulley fits the 2001-2002. , 4.7 engines, The 90mm Tensioner Pulley fits 2003-2007. 4.7 engines If you put the 90mm to substitute for the 102mm you won't have the proper tension on the belt and you are risking the Belt slipping off, , , ,

Thank you .....your video helped me a lot

This video was so helpful thank you!!!

Thanksss❤

Fridge not getting cold

I have a similar problem turn on oven I would come on but does not Heat Oven comes on does not heat