Video

Sure thing, just shoot me and email michael@laserengraving911.com

You can always do manual registration, that what I do and have done on all my jobs, and I know that xTool will be always be improving the camera alignment the more data they get, Thanks for leaving a comment and sharing!

Ill upload it this month, as a short!

Hello fellow fisherman! Yes! I have reviewed several of the xTool products and one thing they all have in common is they are build well, and right now based on my experience with xTool they understand that your success and lack of problems with your hardware is their success, so I do believe they will continue to improve all aspects of this unit and future units. Great question!

I would recommend that you use alcohol or methanol, or if you dont like chemicals, then a light sanding with a fine grit sanding block.

Thank you too!

if you ever want to sit down with me for and hour and brain storm some ideas on how you can make some money with your atom-stack hit me up! Thanks for watching!!

This is a diode laser and fiber laser so its not the right laser for engraving or cutting clear acrylic, You will want the P2 by xTool for that shrsl.com/4iif3

Thanks!

I have put in a request to get you the info :) 👍

By Next year xTool will already have the new WHAM WIZZLE model I'm sure of that! The way they are pumping these machines out 🤣🤣 is nutz!

I agree with that and have emailed them about it. Maybe if more make the request then they might consider it.

Epic! I love it Thanks for the Tip!

@@LaserEngraving911 no problem hope it helps!!!

I think so, its got some serious potential, I'm looking forward to see all the different ways people use the conveyor! THX!

@@LaserEngraving911 the major limitation of the slide deck is its internal speed. If they fed it 4” then used the galvo, fed it again and repeated it would be faster than everything else I own but as it is too hard to setup for comparable speeds to modern open frame diodes.

I've literally made this SAME request to xtools to utilize the galvo

Glad it was helpful! The F1 is still cool 😎. Thanks for taking the time to drop a comment!

Totally ok, we were only using like 35% of what the xTool fume extractor can do, and it did a amazing job, they way they built the F1 Ultra, does a great job of extracting the fumes.

@@LaserEngraving911 Thanks

Thanks so much! apricate that!

You can! Ill cover more of that in my next F1 Ultra Video stay tuned!

Good information! I am waiting to get my Ultra to see if what type of products I’ll be making to see if the conveyor is right for me. Thanks for the video

@@kevinrich4637 Kevin, did you get a ship date? I was told early June, now it’s after the 20th.

@@dian3145 I was told the end of June. My pedal arrived at the house yesterday.

yes 🥺

🤣 no but that dude rips in the Ring!

Im not sure how the bond to acrylic would be, I think it would bond well, but not stand up to heavy abuse.

I do not think the laser pecker is a good fit for this application, not do I think you should buy a laser pecker at all, Im not a fan of that machine, I would recommend to you instead that you get yourself a xTool S1 or better yet a xTool P2 for your first machine to get started. S1 shrsl.com/4d8q2 OR P2 shrsl.com/4iif3 This machine will help you get started in more professional way, and with these machines you can do this method.

@LaserEngraving911 cheers for the info mate I'll look In to those recommendations!

@LaserEngraving911 just looked at the s1 link and it says $799 then changed it over to the uk site as that's where I'm from and the price jumps up to almost £2200 🙄

You bet!

Are you getting soot? in my video there is not soot to clean. not sure what you mean, could you elaborate?

@@LaserEngraving911 Gotcha, I was just curios as everyone else is claiming to clean soot. Im currently doing jewelry, but want to transition into laser burning wood.

Speed and Power are very related. I would start with max power and fastest speed and each time you run a test, drop you speed by 10% until you cut all the way through. Dont change the power. leave it at MAX, also it is crucial that you are in focus and that your air asset is TURNED ON MAX and working properly for cutting material.

@@LaserEngraving911 thanks so much. I had my air assist on automatic. Next time, I will turn it on max. I will create a test cut file using your advice. Much appreciated!!

@@jasmindrace love it

Thanks for sharing.

no fiber glass, or plastic, porcelain bath tubs maybe, cabinets yes pulsed laser only, water based varnish and paint will remove, yes, but fumes will be excessive.

@@LaserEngraving911 thank you

Yes it absolutely cuts clear, and white and all colors. The xTool p2 is a Co2 laser. shrsl.com/4iif3

@@LaserEngraving911 I need a reasonable laser. I have the S1. I need a co2. What would you suggest

@@ginamariegarcia9461 Here are my official suggestions for you the xTool P2, for budget friendly Co2 Laser shrsl.com/4iif3 or if you really want to step your game up, I woudl suggest you look at the Mira 5 or 7 S From Aeon Laser (this is a professional Co2 Laser )and fair priced, backed by an amazing company with amazing people. You can check them out here. aeonlaser.us/mira-s?ref=laserengraving911

@@LaserEngraving911 what does this one do that the p2 doesn't

@@ginamariegarcia9461 The MIra 5 or Mira 7 S is ✅faster, Frame is heavy steel steel, the rotary attachment is easier to use, it is built to last many many years and built to be a professional grade unit, using high quality parts. by investing in the Mira by Aeon, you are investing in your future production and with the faster job speeds you will be able to output many more jobs in a day than the P2 can, also the team at Aeon offers superior customer support and they are located in Florida.

Awesome!

soap and water, if water based ink, and if plastisol you need plastisol ink remover, you can use the screen hundereds of times.