Video

i wonder if a lower power diode laser would work better

Ehat is the minimum wattage needed to cut it.

Great video. I’m curious about what you are using for the masking. Your notes indicate the use of application tape…..is that the masking that was used? Thanks for the video.

super helpfull needed to make a jig for laser cutting my panels, but will do a full cut out to keep panels in place

THANK YOU! Last week you saved us from not being able to deliver several large urgent jobs to some of our clients. If we slowly moved the laser head everything was fine, but as soon as it picked up some speed it would throw the error. Annoyingly, we had this same issue a few years ago and the Trotec tech told us that we had to replace the whole motor. Really wishing we knew this trick way back then.

The laminator you show in video looks different than the one you linked to in Amazon?

yo what ram is that ?? tell me plss

👍👍👍👍👍nice

Imagine working at an indoor pool for 8 hours a day especially just after they dose it vs a fully vented laser cutter on a small sticker , you need a vented system imo , every bit of smoke from a laser is harmful to an extent.

Nice solution, thanks for posting! :-)

Cutting mdf regularly is a sure way to ruin your laser cutter and filters. It will leave a sticky mess everywhere and you’ll be left with a terrible smell that won’t go away. Do not work with mdf unless you’re in a dedicated shop space and are willing to clean the machine and filters about 5 times as much as normal.

Aren’t MDF fumes super-toxic (due to glues burning)?

So using the laser to cut the vinyl leaves the edges pliable and gummy, which is probably why it sticks to the transfer sheet. Would it help to let the vinyl cool before applying the transfer sheet? Also, does the laser leave any burn marks on the vinyl like it does on wood or paper? Thanks.

why does nobody show you how to get the shape you want for your jig. I have pre made leather key rings. how do I get those shapes on a jig?

Great video! It included all the salient details for DIY enthusiasts with access to some serious technology at the same time providing guidance for those of us with a coping saw, a sanding block and access to a local Dollar store. Well done!

I think this could have benefited from mentions on how to prep the surface etc.

Thanks for sharing. Will the acrylic paint stay on the coin?

Just curious if you have an updated source for the paddle material. TIA and thanks for the video!

Well done. Thanks for posting.

Does this mask work ok on MDF with veneers? No issues with it removing the veneer since it’s high tack?

Awesome comments - so very helpful!

nice work :) love the classic design.

thx

Oh my gosh. Thank you so much for this. I have been looking all over for masking tape that will work. I have an xTool S1. Do you have to increase power or speed to break through the masking tape? I’m wanting to paint engraved wood and acrylic.

What type of laminator did you use to apply the paper masking tape to the larger boards?

Thank you for that demonstration! Have you tried this on metal material as well?

How has that exaust fan been working?

What clear coat are you using?

The Way to prevent bleed is Mask, Engrave, spray with shellac (this seals the area to be painted and shellac is the only thing compatible with Oil based and water based paint), Paint and unmask

Thank you for this great video!

thank you very much but do you know where to find such wide tape in Europe/Spain? Maximum here is 50mm (~2inches)

My first laser project making a sign for a restaurant was with MDF. Its my go to flat "wood" product now. Your comments are right on and very useful. I subscribed and will look for more practical tips presented in a clear non-theatrical manner. A lot of CZcams presentations are too much fluff and too little practical useful fact. keep up the good work. Thanks.

1. Engrave then spray with clear coat (2 light cost) then spray or paint as you please. 2. use a heat gun i.s.o. your laser to melt the embossing or powder coat to get an even look. I never done this but common sense prevail.

ive used EZcad for over 6 years no problems on 50 watt fibre, depending on your substrate you can get some really nice defined finishing using crosshatch and alternate it 0 , 90 and 45 135 degrees

Where to buy desing or download and donate? Thanks

There is a video showing a process to make Aluminum tags with painted covering etched with the laser and then etched with Ferric Chloride. And then clean off the paint and with powder coating and a heat gun treated then polished. Makes great tags

Isn’t faux leather dangerous to cut as it contains PVC?

Thank you for making these videos. I bought a laser engraver just because and now I’m thinking of making some sort of side hustle with it as well. Thank you!

You made an excellent experiment and all I read is comments of people who think "they knew better than you"... it is not what they say to you, it is the way they say it. I thank you for sharing this experiment, it is truly interesting, and though there may be even "better" solutions to the bleeding problem, I learned a lot from you. and hoping to see more from you and trying more methods, I will try them myself as well!

What is that tool at 2:47 to apply the mask to the MDF? Also, very helpful and informative video! Liked!

I cannot get 3mm mdf in my country. What other wood or cardboard I can get as replacement?

Excelent video. Which type of paint sticks to acrylic ??

Wooden luggage tags will break quickly. Consider acrylic.

This looks fantastic!

Just saw on the Trotec site, that they use wet towel paper on the bottom of Acrylic sheets for optimum results.

Are settings for the MDF wood the same for plywood

All so adorable. Great videos

Great videos

Interesting video. Hardboard is like MDF. It is used for flooring. A 4' x 8' sheet, 1/8" is usually under $14.00 at Lowes. It's basically MDF, but a little harder.

Does the box stores MDF have glue issues for cutting and engraving like plywoods do with them ?