Video

Cars are stupid. I can't believe people still drive them.

can you see thru it ?

Paul what's a good 3d Printer for printing EUC stuff?

1000 miles and no issues with the trolly handle making noise. The screws do work their way loose and need occasional tightening. But surprised at how usable the handle is, despite the notable shortcomings.

And they want almost $4k for it😂 The only company I'll pay top dollar for is Leaperkim.

I don't even finish watching it, I'll give it like and hopefully the video will get 4 views, just kidding, let it be 4 million, just so I wrote that you find a service that will allow you to promote your channel.

? So you think its funny that eat could eat a cat???? - sicko

Whete is Miss Aubsome ??

😂😂😂😂😂

Amazing Videography & intense ride! bravo! 👏👏🤟

Nice drone shots. Can’t wait for us to do it again!

YEEHAW. Let's do it again. See you next week 😁

Awesome

Hey how do you get here?

Dope riding guys

I've done the same thing on 1000lbs motorcycles. I've even broke loose in a 1500hp drag car, smashing into a telephone pole. Gravel is dangerous Af.

Pedal clipped

Would this be the same for inmotion v12 ? I need to change the bearings .

Always doing too much 😂

Kala dikha raha tha 😂😂

Play stupid games win stupid prizes 😅

Lmao im laughing at this clown , thats what he gets 😂

Learn to wear gear is a wise thing to do.

Damn i can smell the road rash from here 😮

Dude, You're awesome! Thank you.

When you’re not ready to start dancing

I remember back when the hoverboard first came out and i got one. Was taking it out for a spin in the neighborhood and decided to see how fast it could go... got pretty fast and then started beeping and just turned off on me. I FLUNG forward

Yo 😲 Yo 😱 Yo 🤯 Yo 😰 Yo 😭

Imagine thinking your helmet will protect your entire upper body 🤦🏽‍♂️

He wanted to show off

We all need to see this, so you can take your own risk

safer way to open the lid is not to hammering with flat screwdriver as you can damage the rim, but remove both sides of bolts and a little hammer to the axe, then motor stator could come out to oposite side and youre lose bearing grip. Another note, when you put the lid back, hammer with rubber hammer and do not forget to grease around the rim to seal if from water ingres

He needs to work on that trick i think

I’d never swerve like that on a mono wheel holy 😂

Need better grip tires. I dont know if they have triple A grip tires for those unicycles. Would not happen with better quality rubber. Yoy want to be fast on one wheel. You better invest in the best grip.

Oh my GOD!!!! These go so f*cking fast, that guy could have killed himself, wtf?

Great video, but you did not mention what we can use to re-waterproof the motor drum. After opening it will inevitably make the waterproofing worse, so I would like to know how to re-seal it

Is there a way tighten the Gotway pedals so they are tighter when pivoting instead of flopping down fast? I can do it on my Inmotion which has a grub screw but don't see it possible on the Gotway

Skin grafts

dont show me this i wanted one

60 km an hour you fool

😂😂😂

Tryna be fancy. Bet you won't forget this lesson...

Exactly it very bad machine one wheel and if cut off electricity you down harder , one hole on public rd you going down like a clown harder . Finally better two wheels then one , even my nephew 10 years old know this . Finally it illegal on public rd . If Chinese decide to add barrier handle it can be more safe and legal and fantastic

Great video! I’m planning to replace the bearing on my Sherman Max. Which bearing do you recommend? How do you remove and replace the bearing without heating it up?

The foot stands are so low. This happened to me on a onewheel pint. The front is lower then a standard size so when going up a hill its barely any clearance. So i pushed it to hard and crashed.

Sorry be careful my friend

No gear, sagging pants, tryna be "sick bruh".... Squids

What a butcher. Uses pliers as a hammer. starts cap screws into thread with electric screw driver. Applies no fresh loctite to stop galvanic corrosion and prevent galling while doing up stainless cap screws into alloy. Appears to tighten cap screws with ball end allan keys. no torque wrench, etc, etc.

Damn bro! You good?