Video

It could also be the case that If someone replacing the oil PAN forgot to disconnect the sensors and drop the PAN, they tore it off at that point.

I don’t understand. What is it was?

Thanks! New driver here

U can still spec a volvo with a Cummins...

Volvo does btr on mileage then Cummins by far...

You could see it on camera if u left it alone, he's constantly moving it

What you think about 2016 VOLVO VNL64T670

Hi.. is volvo dd13 425hp is good or 455hp.. what is difference?

Where is the tps located on this engine?

Great Video!❤.

What about 900,000

Nice info...Following you sir..

How much do you guys charge for this service? How long does it take?

Worst video

How did the fluid get cross contaminated? How did coolant Fer into tranny?

Complete garbage engines and support Wouldn’t recommend a boat anchor to anyone

Will this cause truck not go in gears and then slowly shut down?tks

Can you do video on shops in Chicago land that can work on volvo motors appreciate

Can you guys provide the information or the part numbers for the correct gasket? im literally in the middle of this right now. so he says to use the UPDATED GASKET OR the flat gasket???

Apply service brakes to distinguish king pin play from steering axle wheel hub bearing looseness .

Great video. Big tip tho. Turn the original audio down and do a voice over, especially when you in the shop, or you in big open areas, or pretty much always. Yeah

I just figured out last night my top U-joint was binding on my 2010 Peterbilt 387. Thought I had air in my PS fluid so I jacked up the truck and ran the wheel hard left to right. Noticed that the binding was every half turn of the wheel. Sprayed WD-40 on the top (rusty) joint and it turns smooth now. No grease fittings so they are likely the originals. Was searching for info on the U-joints and found this video.

Stupid video and you guys talking to much like you on date get a room

That’s Automated, Not Automatic.

As far as new trucks go, why don’t you guys have any Cascadia? I know Freightliner is not the most comfortable and ride rough but I’m in one now and it sure is reliable and easy to fix.

Error code : MID130 PSID40 FMI9. Please help no clue what it could be

Is it worth it to buy a 04 Volvo D12 with 1 million miles for 6k?

Another pointless video

Pointless video

Idk about theses parts and service pretty high in price I seen a price on one just not sure

Yack yack yack... bs!

So after u pulled the sleeves out u installed the special nut do u take the special cut off after u install the regular nuts ?

Even though it’s like a 2007 model is the cab and sleeper brand new? Or did you replace it?

The movement felt in this video could also be wheel bearing play ?

I am not a trucker I assume that the “D” on FLD stands for that it has a Detroit engine. 🙂

It worked for me. I had a 130 code and Check Trans. Now it works great.

I DROVE A T600 I WAS TOTALLY BLOWN AWAY BY THE LACK OF SPACE IN THE CABB IT WAS LIKE A RACE CAR THE T600 INTERIOR FIT YOU LIKE A PORSCHE GLOVE

Is the transmission damage after that?

Don’t cry, Buy scrap 6k that’s it. Without to much talking

Saved my ass just now with this thank you

He said game and automatically wanted to dislike. Trucking is no game. There are no surprises, other than shit drivers on the road and long load times. But as far as expenses, they're crystal clear. You know the cost of fuel, you know the cost of insurance, you know the cost of taxes, nothing suddenly changes without notice.

Hub alone cost $1,500. If you're shopping for a truck and see those hub caps on it , turn around and walk away.

En español no tienes

Bull 😢

I just fixed my damn truck because of this video !!!!! I have been wrenching for fifty years and have replaced mayby 2 steering ujoints in all that time, and it was because of looseness not binding. So I'm very glad I saw ur vid. Thanks guys! Well done!

6 min vid in 30 sec. Disconnect the batteries for twenty mins.

Change the valve still leaking

Do you make them for dual steel wheels?

I bought D13 when it have 350,000 miles .now have 871,000 just put water pump till now.

Would this cause grinding when turning slightly, right?