Video

Hi mate, can you actually list the parts for the retractable setup please? I've just got my hands on an m680 and want to set this up.

Awesome work

Thanks for including your gimbal settings. I'm using it as starting point for carrying a7sii on M5 and s1000 and seems about right.

Been here. Cheers from Mornington

Such a wonder of the world. Spectacular views - would visit there again!

Not quite. Obviously still doing the same thing. Just not as bad. I'd do an advanced imu calibration. Especially if its nevr been done

I tested your ronin settings today with GH5s + 12mm f2.0 and finally everything worked as it should. You are great! thank you!

Cute!

Hi

You should check out the Eclipse Rovers. eclipserover.com

can you try flying bit higher where the winds start to pick up... this is 20m of the ground. bring it to 50-100m, does it start to shake?

footage was sped up by 500 %, did you do any other changes like stabilize the video? how about a test at regular speed of drone where you do not need to speed it up later in edit...

hi ... i have same setup with m600pro and sony a7r2... also i find wind is killing the ronin mx and shaking is terrible no matter of software adjustments... i added foam insert in between the gimbal mount and frame and that removed propeller and tiny vibrations, however i still experience problems when there is any wind ... it just seem pan cannot stay in place ... i use zeiss 35mm lens, i will try to make it as heavy as possible for my next test, by adding extra battery grip, polarizer and nd iflters to the lens, and extra ronin battery attached to the back, as well as using the lens suport on ronin and perhaps some counter weights mounted at back of camera.... if in the menatime you got any new tips please share...

Nice!! Is it pro res or raw?

Looks over sharpened to me but other than that looks fine but what did you encode this footage at it looks a bit low in bit rate

Any issue fpv? I've got phantom 2 with h3.3d but just got hero 4 black and my fpv goes out in 30sec untill I push button GoPro and it comes back

Come on Kinefinity ... We all want that juicy camera 😡

loose the folding props balance good qual carbon and mount the gimbal under the harmonic stioll point in the center of the machine stick the batteries on top. this will make best of the system potential vibration damping and get rid of the occasional vibes in the footage.

Hey whats happening? So just out of curiosity why is the base ISO 500. is it bad to use a lower ISO with Cinema DNG and apple pro res? I read a article about the D-log locking at 500 ISO. Do the cinema DNG and apple prores lock at 500 as well?

F16? Yikes to start with diffraction on m43 20mp sensor should redo test at F5.6 maximum also hard to tell with CZcams compression going on . What were your findings on your screen? Thanks

yeah - image quality is good - they had me at SSD !!!

How did you perform the IMU calibration of the M600. Did you have to tilt the matrice on its arms? I have an Inspire 1 and all you have to do us place it on a flat leveled surface. But the Picture I got when trying to calibrate the M600 was unusual to me, the picture showed the Matrice on a tilt position resting on one of its arms. I that correct? thank for your help.

Any low light samples? The KineMAX 6K looked pretty nice (ish), I was wondering how this stacks up against the KineMAX and the Raven and the a7sii.

what lens?

i think this is my next camera,

such an awesome camera

Thanks for sharing the footage! I too am considering the Terra 5K as my next camera and the noise in the shadows concerns me. Is there anyway you can upload the same footage without the VisionColor LUT? Maybe just the standard rec.709 LUT?

I have a similar issue with the regular ronin.

Looks like a scene out of Predator.

the wide is amazing. the colours are beautiful - pity about the terrible noise in the shadows. watched at 2160p

Nice shots. Terra - so much noise in shadows :( Thanks for sharing

Was it the outfilter parameter you changed for vibration? Im flying a Red Epic on MX with M600 and can't get rid of high freq vibro even at very calm weather. The stabilization is great but that high frequency vibration spoils the whole footage. Would like to know if the outfilter was the main parameter that helped you get rid of those vibros. Thanks (and nice test videos btw ;)

"...After fight with the MX" What did you mean? Had a problems with GH4? Or some other general problems with DJI...?

So How did you landing ?

Hi, We have now tested GH4 and A7s. No smooth footage yet. Any tips or help please? We are thinking the damping needs modifying or the camera's are too light? Many thanks

No sure if you reply to comments. but I have recnetly noticed with my gimbal is sometimes rolls on a certain angle when I have it in tilt mode. And when in post production I have to recrop the video so it looks leveld. Any idea why this is happening?

Did you ever get the best down or did you have to "crash' land?

Hello. I assume you're getting your live video feed from the GH4 to your tablet. Can you tell me if you're just using the hdmi out from the camera to the lightbridge transmitter on the M600? Also, are you able to remote zoom/focus the GH4? Thanks so much!

Great video THANKYOU! Quick question did you land at 20.8 under load? Or was it reading 20.8 after land? Thanks!

How big is your car? Relative to the scale? you have already seen my RC buggy

Could you tell me what your custom settings are? I have same setup but using A7s II. The ronin shakes to much in small turbulence. If i try to put stiffness past 25 (Which i need to do in order to stop shaking?) The ronin Vibrates too much. What setting should i use to get the authentic 3 axis gimbal behavior. Ronin is acting like a crappy gimbal.

which one do you think could be better moza lite professional or DJI ronin mx?

Why would you shoot in LOG and convert to REC709 then apply a LUT to 709? Whilst I can imagine your output being 709 (H264), but if you shoot in LOG your editing will be much easier wiht a transcode to Apple ProRes422 and applying a LOG LUT. If you were editing H264 (or similar) you would apply a Rec709 LUT

How is the IMU Calibration done? Did you already fly the critical pattern I mentioned?

Is it me or does the camera seems to vibrate a little too much? Its pretty noticeable

It's truely better. But you didn't fly movements that provoke the problem. Horizon drift mostly occures when you fly sideways, gaining altitude with an additional yaw input. (In short: fly sideways to the right, gain alt, pan left with yaw and pan down a little). That is the typical POI movement. Show me that - if the Ronin MX manages to keep the horizon level: 1 million thumbs up! ☺️👍🏽

How did you get the matrice so soon? did you order directly from dji? How did you fix the jello and vibration? I saw your first video, that had me worried since I've placed my order.

This is not an "base invert position" i think. The error is to have set de camera base invert mode on enabled. I think this mode must be enabled when the base plate si inverted (not necessary for upright position), that's to say when the base plate is close to the battery. Look at the manual p 24. Sorry for my english if you don't undertsand ;) If you want to be on upright position, you have to invert the base plate for the camera to capture footages upright, and then, don't forget to enable invert mode, or to leave the camera on the wrong side (like you did), but without setting the base invert mode. Here, your base is not inverted, you only turned the gimbal into upright mode. That is how i understood the manual. I don't have the MX. Let me know if it worked fine

15 minutes flight time is really long. I don't see the benefit in 5 minutes more for me. But thats an individual thing. If you need it, theres surely a reason. You can't travel with any of those LiPos. It's the sum of watt hours that you are binging on a flight and not the wattage of a single Lipo. 160Ah in total - thats it! A joke! IATA kills our job. :( I bulit my copters with higher payloads and lower payloads - just as optimized as I need it. DJI really missed the target - they are putting the stress on the wrong points. Two seperated battery circuts would have been sufficient. 6 add weight... and so on... There are some more things that are a bit away from the need of a pro user. Sorry...

Ha! I can't believe it! Look at the horizon - If DJI would have managed it, it would have been a revolution. But this is simply worse than what we've ever seen. I predict on top of that that the M600 will not be selling very good. Imagine - for one fully loaded flight in maybe 18 minutes you need 800.-$ worth of batteries?!? Ha! thats a joke! I make up to 15 flights a day with my 5000mah 40c 6s lipos. (Okay - I only fly 12 Minutes) but imagine what amount of money in batteries I would have to carry around. No thanks DJI - wrong concept. Professional pilots have settled on way better systems some time ago.