Video

This video shows the modifications I have made to the electronics of this Diecast Masters RC Lowboy. These modifications make the gooseneck and tail lights remote controllable, removing the 3.5mm connectors. (Sorry about the audio in some places, not sure what happened here) The winch controller used from from Hey'OK Performance. Al produces some of the best electronic controller available. Lin...

Here is a quick video showing the failure of the FS-i6S. Both jog dials do not work properly; factory reset and firmware updates have been performed. This is a bad board that both switches connect to.

Converted Bruder trailer offloading an excavator and onloading an earth mover. Here you get to see my horrible skid-steer skills in action. Many of the parts were designed on Fusion 360 and Printed on my Creality CR10 printer.

See my other videos for the write up on this rig.

Here is my Bruder trailer conversion, made to be compatible with 1/14 scale Tamiya RC trucks. The cab for this truck/trailer combo will be modified next for RC. Much of the conversion was designed and 3D printed using Fusion 360 on Creality CR10 and Pruse Mini printers. • The electronics are somewhat custom, using a Hey'OK remove made for RC crawlers with winch in/out, dig servo and lighting co...

Here are some disconnected thoughts on this trailer, the build, and its value.

My TRX6 military crane. The chassis and drive train is TRX6, the body and crane are from Banggood, and rest was fabricated by me. My build threads go through just about everything I did to get this rig running, including the Thingiverse links for cab bracket, that attaches it onto the chassis. Build links: RC Crawler: www.rccrawler.com/forum/traxxas-trx-4/620725-project-m8-trx6.html Traxxas: fo...

Here is my Tamiya forklift kit. It comes as a wired-remote kit, I switched it over to full remote using a Spektrum DX6e. Driving is a little rough, I don't have the expos set properly yet, so the skid-steer is a little wonky. It uses three 10A ESCs I got off of Amazon, a small 4-ch DSMX receive, a Hey'OK blinker, a CC 10A BEC and Common Sense LEDs. The Cab, running boards, light hangers, and wi...

Here is a slightly modified E 1:24. The ESC/RC has been replaced with a HW1060 ESC and 3 ch Spektrum RX. I designed and printed the electronics tray, the roll bar, and front grill. The build thread: www.rccrawler.com/forum/micro-scale-rigs/621017-greatscott-enduro-24-a.html Thingiverse files: www.thingiverse.com/thing:4613414

Added more to my backyard crawler course. This is a quick video of my TRX6 running it.

This is a modification removes the need to plug in the body to the chassis to power up the lights. Full write-up: forums.traxxas.com/showthread.php?9092331-TRX6-quot-No-Wire-quot-Lighting-Mod-(Maybe-TRX4-too)&p=6533685#post6533685

This is my Element RC Enduro kit build with an Injora Comanche body. This is my crawler course in my back yard. At the end of the video I got distracted and lost the video frame. The build thread is here: www.rccrawler.com/forum/element-rc-1-10-enduro-trail-truck-sendero/614202-greatscotts-element-kit.html

Here is a video review of my Element RC Enduro kit with Injora Comanche body. • Base chassis build and instructions • Modifications to the chassis set up • Electronics • Injora body with mounting and instructions Most of the 3D printed parts can be found on Thingiverse. • SSD (SCX10ii) Front Bumper Mount: www.thingiverse.com/thing:4139238 • Chassis Brace: www.thingiverse.com/thing:4130716 • SW4...