How to Tune GY6 Carburetor Idle and Idle Mixture Screw 10 of 12
Vložit
- čas přidán 29. 08. 2024
- Thank you for watching and supporting my channel feel free to use my referral links. If you need help with any of these products call or text me Mike (209) 355-8088. I usually respond within 24 hrs.
--------------------------DO IT YOURSELF--------------------------
Time Required: 60-120mins.
Skill Level: Medium
Chemical Used:
• CRC Freeze-Off Super Penetrant amzn.to/2wn3BSN
• CRC Sta-Lube Anti-Seize Engine Assembly Lube amzn.to/2uK30Kp
• CRC Sta-Lube Moly-Graph Grease amzn.to/2uJlkTQ
• CRC Throttle Body and Air-Intake Cleaner amzn.to/2x5HMrd
• Bel-Ray Oil Exl Mineral 4T 10W-40 amzn.to/2TPO6dZ
• Loctite Threadlocker Blue 242 amzn.to/2TqYtF3
• Mobil 1 Synthetic Gear Lube 75W-90 amzn.to/38yHtCh
• Mobil 1 Synthetic Grease amzn.to/38h6ilO
• Permatex Copper Spray-A-Gasket Hi-Temp amzn.to/2wkt4Mw
• Permatex Dielectric Tune-Up Grease amzn.to/39CcA14
• PJ1 1-12 Cable Lube amzn.to/2WBwUvZ
• Rust-Oleum Dissolver Gel Spray amzn.to/38C0DHb
• WD-40 Penetrant Spray (Blu Torch) amzn.to/3cotcLn
• Scott Shop Towels amzn.to/32Hjwau (optional)
Parts Used:
• SSP-G 180cc Big Bore Power Kit bit.ly/2v5ZCd1
• Ban Jing High Torque Starter Motor goo.gl/wTTSJn
• Ban Jing Performance CDI + Coil (2-in-1) bit.ly/39dHagk
• Briggs & Stratton In-Line Shut-Off Valve amzn.to/2WMryy7
• Carburetor CVK Main Jet Kit bit.ly/2J6ZkGf
• Heat Shrink Tubes amzn.to/2WDaYjZ
• Helix Fuel Line 1/4 ID x 3/8 OD 3' bit.ly/39UumN2
• Helix Fuel Line 3/16 ID x 5/16 OD 3' bit.ly/2wjcs8p
• K&N RC-1290 Cone Air Filter amzn.to/3bbeQwG
• K&N 81-0221 Fuel Filter amzn.to/39dJQuo
• K&N 81-0261 Fuel Filter amzn.to/2wnG6td
• Naraku Intake Manifold Coated Non-EGR 32mm bit.ly/2vMyIY0
• NCY Carburetor CVK 30mm bit.ly/2vMyIY0
• NCY Shocks Adjustable Damping Nitrogen Absorber bit.ly/2UcoLMU
• NCY Throttle Cable 76" CVK Assy bit.ly/2ZhdTP6
• Shorai Lithium Battery 12V 14Ah bit.ly/3d03IV6
• Shorai Lithium Battery Charger bit.ly/2w6OhK9
• Hoca Brake Lines bit.ly/2IN9wDG
• NGK Spark Plug Iridium CR7HIX bit.ly/2TOopup
• Scotch Super 33+ Vinyl Electrical Tape amzn.to/2x0uwEd
• Solder-less Seal Wire Connectors amzn.to/2vyIqNt
• Stebel Air Horn amzn.to/2y44Wi8
• Stebel Air Horn Wiring Kit amzn.to/3bdR6YO
• Steel Fuel Clamps 6mm amzn.to/3dlwgIZ
• T-Tap 1 Wire Connect amzn.to/2TbZqSA
• T-Tap 2 Wire Connect amzn.to/2PDAIsm
• Zip Ties 4" amzn.to/2J9KyhW
• Zip Ties 12" amzn.to/32GtBo5
• Zip Ties 27" Stainless Steel amzn.to/2Ibcxgy
Add-on (optional):
• NCY Oil Cooler 17mm Kit bit.ly/3aWsMKZ
• NCY Oil Dipstick bit.ly/3akUDEM
• NCY Throttle Grip Set Bearing Style 7/8in bit.ly/3g37Hkh
• Taida Carburetor PE28-mm Racing bit.ly/2QDxXrw
• Taida Intake Manifold Polished Non-EGR 28mm bit.ly/2xU4dzQ
• Taida Throttle Cable 76" PWK Assy bit.ly/2Zj8F5p
• UNI Air Filter Pod 50mm 15°Angle bit.ly/2UuOCON
• Ban Jing Starter Clutch Heavy Duty bit.ly/3cJUxYz
• Crankcase Bushing 3-Piece Set bit.ly/2Qe6rRd
• Dowel Pins 8x10mm Set bit.ly/39B3oKf
• Dowel Pins 10x14mm Set bit.ly/39CKaE5
• Hoca Crankshaft 2.5mm Stroker goo.gl/1unUmv
• Koso Super Flow Oil Pump goo.gl/GTWZdB
• Starter Clutch Nut bit.ly/3cJTlo8
• Woodruff Keys bit.ly/39yuaDe
• Performance Oil Seal Set bit.ly/2VCyxsI
Tools Used:
• 8mm Hex Bit Socket amzn.to/39AuO34
• 8mm, 10mm, 12mm Sockets with 4" min-ext Wrench amzn.to/2vow36J
• 9mm Wrench and Adj. Wrench amzn.to/2vow36J
• Bearing Separator and Gear Puller Set goo.gl/Vs6C6Y
• Big Head Phillip Screw Driver amzn.to/2vow36J
• Cable Lube Tool amzn.to/2WBvpxy
• Digital Multimeter amzn.to/2xe4qhc
• Feeler Gauge .004, .005, .006 amzn.to/2wjyiIq
• Flat-Head (narrow) amzn.to/2vow36J
• Flywheel Puller goo.gl/GNToF7
• Heat Gun Handheld amzn.to/2uHQU4i
• Hydraulic Compression 12-Ton amzn.to/3axX8mT
• Impact Drill amzn.to/2wsdfDp
• Impact Socket 17mm amzn.to/2uReXOu
• Impact Socket 39mm amzn.to/2PXNjX8
• Mallet Hammer amzn.to/38gJumk
• Needle-nose Pliers amzn.to/2vow36J
• Oil Cannister Pump amzn.to/334xxPz
• Oil Drain Pan amzn.to/330TEGM
• Oil Funnel amzn.to/2vR8D9Z
• Propane Torch amzn.to/38g4bPw
• Seal Driver #4, #6, #7 Set Kit amzn.to/38gxwJq
• Slide Hammer and Bearing Puller Set amzn.to/2x53xHE
• Starter Clutch Nut Socket 3.25” min-ext goo.gl/5rMgtS
• Torque Wrench 5-35’ Foot Pounds amzn.to/32O0FL8
• Variator Tool bit.ly/3cqJHGY
---------------------------
Need more info on GY6 BIG BORE KITS?
Visit our Blog Share: ncystore.com/blog
Carb sounds barky. It's not a dog, it only happens when he touches the start button. His confusion on counting how many times he turned a screw is baffling! Yet, I'm watching...:) Thanks for the vids!!!!
Even the damn dog is like: "Get to the frikkin point already!!"
lol
Damn! took long enough to get to actual point of the video..... Geeze he goes from lets start it up to talking about his exaust for damn near 3 mins ...
Clean motor great mechanic but that body has to G 2 The muthafuken O Bro Mane but thanks u have helped me much
Get on with it dam I fell ASLEEP TILL THE DOG STARTED CRYING
hahahah
What he said.
😆 😂 😄 🤣 😂
OMG!!!! THAT CRAZY ASS DOG WAS DRIVING ME ABSOLUTELY CRAZY... I HAD TO QUICKLY TURN IT OFF!
me too, we called fox and donut their names.
The dog is crawling everytime you push the push start lol hahaha
You need to have the engine running when you do all this. Also adjusting the air mixture screw is not really instantaneous you need to adjust it while the engines running then ride it around the block then adjust again right it around the block repeat until it's perfect
I knew it was never gonna start with barely a turn and a half. It sounded like his scooter was barking when he tried to start itt.
This video suck. Talked more in depth about the exhaust than the actual tuning of the carb & starting.
Where you buy that exhaust?
What kind of tire is that,....? (Jabberjaw!
If you going to entitle your video HOW TO TUNE A GY6 CARB, at least know what your doing, and get to the point and less talk.
Thanks bro. Appreciate it helpful
So I can be of help
Hi,
so what should I do to run round???
Turn the air screw one snd a half turn, ok.Where should be the idle screw to stay idle?
And where should be the carb needle clamp from the top of the carb?The needle that came in the main jet I'm talking.
Thanks.
Just play with it, you get a feel for it.
Just play with it 😉
@@vladimpaler9274 That's what she said
Wow
Anyone help have a gy6 150cc atv takes off perfect but onces u have full throttle it starts making a bogging noise nd just seems dead at full throttle only hitting 20-25mph thanks
Good video
Talk too much about the exaust
I only needed to know about tuning the carb
does a bigger carb need smaller pilot jet ? stock carb was trash and im going bbk soon so i bought a bigger carb. but it wont idle at all after auto choke did its job, spark plug dark black carbon, and fully seating the mixture screw doesnt seems to lean it off. but when i richen it , i find gas on the spark plug. so i guess the main jet is jsut too big while im still stock 50cc ?
new carb is 18.5mm, both jet same size as stock ( i know i need smaller main jet i have a kit on the way and its not related to idle it appear ).
it is hard to start but it does. it idle around 4000 rpm on the choke and after it it drop to standar 1700 rpm then it die. i can start it back only by cleaning the spark plug.
Bigger main jet if the carb is bigger. Remember, more air means more fuel. I had that issue when I installed the 100cc big bore kit on my 50cc. I automatically bought a 20mm carb for it but it wouldn’t run correctly….. so I played with the main jets a little and I ended up running #92 main jet where as the stock one is like a #84 or #86. If you’re keeping it as a 50cc but want more performance I would say, whatever main jet you have in there currently, go up two sizes and if that’s too rich back down to one size up. Once you do that then I would mess with the idle screw and air/fuel ratio screw.
Just start the damn bike
where is 11 of 12..... did counter turn the screw to fix why the bike died at the end of the video
Damn 9 minutes and 42 seconds of my life wasted. Can you say a monkey screwing a football would have had more information.
Yeah I hear that noise it's called that fucking dog yapping in the background. Just kidding man I like your video and look up fat mikes. My gy6 150 was stolen and I finally found it with the exhaust snapped off so I bought I finally found it with the exhaust snapped off so I bought When off eBay and it's nice and throaty but I think I'm running lean because she's back firing.
Yeah I know can do the dog stay unfortunately sorry for sure I'm glad you got your scooter back
What kind of exhaust is that
My carburator starts to leak when masking it richer
Wow is all I got
Why dog is crying yo??!!!
What is up with the dog
Man your dog🗣️
yes, not mine dog really, bugy me too!
This is painful to watch from a person that loses count at half a turn 🤯
Thats just confusing bruh
So much wrong here. Read the muffler directions first, get screw directions figured out, "ceramic-plastic"? Seriously. Stick a sock in the dog's mouth or move it away from your video. I want my 9 minutes of my life back, please.
Are we hiring ?
sure send you resume mk@ncystore.com
Your valves sound little loud
No good you need tunning up youre scooter
Will do just that, about tuning, latest video series soon.
@@NCYSTORE do you need to screw it in to not make it run lean or screw it out question
Can't even hear you with the dog in the background making the video useless
Nothing good
Jesus, stick to the bloody carb!
wasted my time here
You talk too much