Thanks so much man, it took me a good two days to figure out how to get this rear cover off and I couldn't figure out what I was doing wrong. But I followed what you did and it finally worked. Obviously you have make sure you have the screen laid down on something soft like a bed or a towel or something to make sure it doesn't get scratched and make sure you don't use a knife or anything to wedge the screen out, I just ended up using a flathead screwdriver to hold part of the left part of the bottom part up, then I slid the guitar pick up and down the gap between the screen and the frame, then wiggled it up and until it finally clicked and the screen on the that side came loose, then I did the same for the rest of the screen and finally got it off.
Finalmente me decidí a desmontar el mio un Lenovo AIO 520 24ast (24 pulgadas) para meterle 4gb más de ram y un ssd de 240gb nmve. Pues ya que se me ha ayudado, lo correcto es que comenté en indique aquí como fue el proceso. La referencia fue este vídeo, el cual seguí casi al 100% El video oficial de lenovo no sirve de mucho, no es tan fácil como lo pintan ahí. No es fácil, no es como otros equipos, quitar tornillos y listo. La carcasa está ajustada al panel como por unos remaches que hacen que esté perfectamente encajada y es complicado quitarla. Describo los pasos que seguí yo: Consideraciones iniciales: - Abstenerse si no se esta habituado a desmontar equipos, no es nada fácil y es muy delicado - Nunca forzar nada, con paciencia y firmeza, no a lo bruto - Adquirir herramientas específicas para desmontar, más que nada hace falta una cuchilla, paleta fina y firme ya que el hueco para introducila es inexistente. En mi caso use una herramienta de apertura/paleta GB-5A, comprada por 1 euro. - Dejar la peana puesta, ya que esto nos permite descansar, y apoyar normalmente el equipo mientras se manipula. Además al poner los módulo podemos encender el equipo aun desmontado para verificar que todo esta bien antes de cerrarlo. - Hacer el proceso poniendo cartones o algo blando de debajo. En mi caso use un sofá antiguo como mesa, así el panel no sufre daños al estar manipulando los bordes. Proceso: 1) Quitar tapa trasera que rodena la peana y tornillos, sencillo. 2) Primer problema, al quitar la tapa y tornillos anterior nada sucede, hay que meter una herramienta tipo cuchilla (GB-5A) muy fina en la parte inferior, entre el panel y la carcasa e ir pasandola de un lado a otro hasta que se va separnado la carcasa del panel por abajo, partiendo de la zona donde no está el tornillo inferior. Al principio cuesta meter la cuchilla entre panel y carcasa, pero una vez metida con cuidado la vamos paseando suvamente hacia el otro lado hasta que se vaya abriendo un pequeño hueco. 3) Nuevo problema. Al girar el tornillo de la parte inferior este esta duro, no hace nada. Debe ser como un resorte, no es un tornillo en sí. El truco es despues del paso 2 (y como se ve en el vídeo), dejar la herramienta metida en esa zona haciendo palanca, mientras se gira el tornillo insistentemente, llega un momento que 'salta algo' y sale ya buena parte del panel por su parte inferior. 4) Con la herramienta indicada, la introducimos ahora por un lateral y la vamos pasando de abajo - arriba varias veces, parece que no pasa nada pero al cabo de unas pasadas notamos con 'salta' una zona de la pantalla, como si se soltar de una presilla o algo así, seguimos con insistiendo hasta que salte todo el lateral, al acabar vamos al otro lado y cuando parece que ya está hay que hacer lo mismo en la parte superior, ..., el panel está como pegado a los bordes. Ojo aquí no ser bruto porque como metemos y hacemos palanca con el panel podemos cascarlo. 5) Una vez salga todo el panel hay cable que va del panel a la placa que hay que quitarlo de unas presillas, no hace falta desconectarlo que es bastante largo, además así podemos encender el equipo para probar antes de montar de nuevo. 6) A partir de aquí ya es más sencillo y más estándar, pese a que mi placa no es exacta al video es poner la ram en su sitio y el ssd nvme en el suyo (el tornillo en mi caso ya venía puesto). 7) Una vez puesto y probado, montar de nuevo que es muy sencillo, con las manos acercamos el panel a la carcasa y con una suave presión ya oimos 'clacs' en varias zonas de que se encaja de nuevo. Montarlo es coser y cantar. Y eso es todo. La verdad es que es lamentable que un equipo como este sea tan complicado de desmontar, nunca había visto un pc tan complicado en ese sentido, pero con paciencia y sentido común se consigue. Insisto en mirar el video con detalle, ya que fue mi referencia y me sirvió de mucho.
excelente amigo este vídeo y tu aporte me servirán para realizar el proceso, una pregunta tu le pusiste un disco de estado solido, se lo adicionaste? o le remplazaste el que ya tenia?
@@alextgsrr71 Por lo que yo sé y al menos el 24AST no admite ssd m2 Sata, ha de ser m2 pcie nvme, este es el que yo compré: YUCUN 240GB SSD M.2 2280 PCIe Express GEN3.0x4 NVMe www.amazon.es/gp/product/B07HVSF68X/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1
Thank you for a great video. I also cracked my screen and destroyed mine. Be aware this one breaks supper easy. Good luck everyone. This video is the best I have seen and I broke mine anyway. Do not blame this man who gave us the video blame Lenovo and the design.
It was very helpful for me as I had problem with dismantling my AIO 520-24 AST for installing SSD drive. It's not so easy when you do not know where to push...
I've seen the cracked screen commentaries and all I can say is - I followed the steps and had no problems. This person makes this look fast and easy and I think that's what's tripping people up. This is someone working with a practiced hand - most of us are doing this for the first time. Go SUPER slow, be extra careful, watch the video 3 times before you start, pause the vid and do each step really slowly. The plastic casing is gonna make a shitton of horrific I-sound-like-i'm-coming-apart sounds - focus on not torqueing the screen and don't worry about the plastic complaining and you should be good.
So first you have to unscrew the 2 or 4 screws under the cover of the stand, then plug out a bit of the side plastic mounts, and then screw the botton frame screw. Yet, even after that, I cant seem to pull the screen off. Frustrating.
Para aquellos que tengan problemas con la pantalla (muestra lineas horizontales y se congela la pantalla y no responde el teclado ni el mouse), hay que limpiar la memoria y cambiarla de banco y listo
You opened that up roughly but safely. I tried opening it even gentler and ended up separating the dark screen which is glued ON from the digitizer behind it. The computer would not separate along the side or top enough and my plastic tools didn't help. A word to the wise, be aware this is a hard case to open. I have another new 520 and I WON'T be opening that one EVER.
Wouldn;t you know it, 3 years later and I have to open another 520 which is giving me hell. It separates but refuses to come off clean, hanging onto to every tiny plastic tab and then some. What a pain. It really didn't need to be like this. It isn't Fort Knox. Still don't have it opened fully.
I managed it just fine without breaking it, it was still a pain in the arse and took ages to figure it out but you've got to make sure you don't force anything where it's not meant to be forced and make sure you used anything sharp in between the screen and the frame.
Thanks. Very useful. Just upgraded my RAM to 12GB. BTW, you don't need to pull out the connections. The RAM can be easily updated without doing that. Just remove the circular stand and it opens up totally.
@@stevengarcia9882 It has been a long time since I ordered mine, but if you Google LM238WF2 I think that was the (non touch) screen that I ordered. There should be some available to buy on eBay etc.
In order not to brake the screen, follow the instruction laid down in the file "ideacentre_520-22-24_hmm_20180614.pdf". You can find this guide using Google. No sharp tools for detaching side and upper side of the screen!
After my experience today, I would not advise doing this. I cracked the screen despite being as careful as I could. Take your pc to an "expert" so that if they break the screen, it is their fault.
uhhh im not sure your supposed to crack the screen. worked well for me. maybe try laying the monitor on a flat suface and make it facing the surface without your impaling yourself with the suport rod thing
hello, thanks for the video. also i want to remind you that you've forgot to mention the authors of the song you use. youtube sometimes delete account for that.
Thanks for the vid but ****WARNING****. I have dealt with all-in-ones for years but this one is a nightmare. The screen cracked and I had to spend a couple of hundred pounds to replace it for my customer. I will not be dealing with this model again...
Před 4 lety+1
It is a bad order. First you have to turn the screw, then you can use something like a spatula to separete the screen from base.
I cannot loosen the screw! It is too tight. I know I'm supposed to turn it to the right but it won't budge. I'm in danger of ruining the thread on the screw. Any tips on loosening it?
Ok I sussed it. Required better screw driver and more brute force. I would recommend using a credit card to slide round edges of screen rather than a screwdriver. Easily the hardest case ive had to open especially with the high risk of damage!!
yeah it can be removed. just flip your pc with the monitor on a flat surface and under the stand there should be a screw. using either your thumbs or a screwdriver just unscrew it off and there you go (you might also have to take off the cable management thing shaped like a 9 if that helps).
tried to open one of these, 2 hours, careful the screen always in tension, almost break fuck lenovo and this design aint gambling a new screen (25+ years of computer building/laptopr repair experience)
Bang maaf mau tanya, Itu Ram yang bawaannya dari pabrik On Board kah atau gak??? Trus untuk yg Upgradenya ada Slotnya sendiri khan itu yah?? Mohon bantu dijawab yah bang segera 🙏🙏
No need to open the top of this machine to insert ram, open bottom only by pulling it away from the case, then pop off metal access panel at top right, the insert ram... done. This video does it the hard way.
Buen día a todos, si alguien tiene problemas para formatear una PC como la Ideacentre AIO 520-22AST o similares, ya sea con el sistema operativo Windows 10 20H2 en adelante, si la computadora se les reinicia al iniciar con el medio de instalación o USB de Windows, deben de actualizar la BIOS de la PC para que pueda funcionar bien la instalación con versiones más recientes de Windows 10, otra alternativa también es instalar una versión de Windows 10 anterior, como la 1909, por alguna extraña razón éste tipo de computadoras ideacentre no funcionan bien con nuevas versiones de Windows 10 como la 22H2 que es la más reciente, así que actualizando la BIOS debería de funcionar, además de usar su unidad de instalación de Windows en UEFI, si actualizan la BIOS de la computadora, tenga cuidado, ya que si se apaga la computadora si se va la electricidad, quedará inservible la computadora y tendrán que reprogramar la BIOS lo cual puede ser costoso Good morning everyone, if anyone has problems formatting a PC like the Ideacentre AIO 520-22AST or similar, either with the Windows 10 20H2 operating system onwards, if the computer restarts when starting with the installation media or USB of Windows, they must update the BIOS of the PC so that the installation with more recent versions of Windows 10 can work well, another alternative is also to install a previous version of Windows 10, such as 1909, for some strange reason this type of computer ideacentre don't work well with newer versions of Windows 10 like 22H2 which is the most recent, so updating the BIOS should work, as well as using your Windows installation drive in UEFI, if you update the computer's BIOS, be careful , since if the computer is turned off if the electricity goes out, the computer will be unusable and they will have to reprogram the BIOS which can be expensive
Bang mau tanya. Tahap awal kok tinggal pencet aja sih?? Punya saya dipencet ga bisa, di cungkil juga ga bisa. Apa harus lepas kaki Bawah (yg bulat) dulu ya???? Mohon direspon🙏🙏🙏
Thanks for the review. Sorry if this's too late, but is the GPU upgradable? I searched far and wide but didn't find any relevant info. Can you confirm or deny, and if so what form factor should I look for? Thais in advance.
@@abhijeetkatiyar7209 unfortunately no, I found out the GPU isn't upgradable, but tbh it isn't a big deal now that I've spent enough time on this desktop and came to know what it actually is, and is not, meant for.
mengikuti tutotial ini menghasilkan panel LED saya pecah ! mungkin sebaiknya ditambahkan keterangan suara maupun tulisan mengenai beberap bagian yang harus hati - hati.. soalnya kalau ngikutin di video kayanya enak sekali bongkar bongkar pas bagian layarnya, hiks hiks..
Some scaremongering going on here! Yes the 520 is a fiddly little wotnot to open BUT WITH CARE it pops open after some delicate patience. I've opened mine twice now without incident. The only bummer is you cannot fit a standard 2.5in SSD with adaptor bracket. The mounting bracket for the 3.5HDD is bespoke and will not accept the adaptor sufficiently well so be prepared for some metal work unless you install a m.2 SSD.
Please who can help me I opened my device to clean it with air but after turning it on the picture is not like before. Lenovo logo is not clear and the blue screen look like purple or. Pink screen
Thank you mate..... It be helpfull very.... One question.. I opened and now i want to install extra M.2 SSD 128GB or 256GB - the question is : How it works that extra drive? Is it be as second drive in "My Computer" then i will install there separate System or it just work as Flash memory to speed up our 1TB disk ? In AMD StoreMI technology? Then i will buy only small 128GB. But i would like to buy 256GB install there all System Files and keep picture, and that 1TB Setup as second Quiet (power off set after 5min). Can you please answer for that question please.... we have so less options here in BIOS i wondering maybe lenovo just block the way how we can use it.
This pc have like 4 or five models. Some jabe ebetter processors or integrated graphics. This is a lpw end pc . I was upgrading ram too from 4GB to 12GB . But i think 8GB is the sweet spot for every model. Tell me the cost of ur pc and i'll recomend better. Sry for bad eng
@@bootlegscarce0844 i want to buy M.2 SSD for my Lenovo AIO 520 24ARR which i just opened. My question is... because Lenovo set up 128GB SSD + 1TB 7200rpm usuall... how they did that. Is it working as 2 separate storage or as one (like FusionDrive where 128GB be used as FlashMemory for basic drive using for example AMD StoreMI technology). In normal desktop i will set up as i want, but because here is no any options in BIOS i wondering it may work just in one way. My idee is to buy 256GB, install there system and keep necesary files, and 1TB just leave for videos (and set up power off for this drive after 5min to don't listen any noise). Can you please give my advice if you know anybody who using AIO PC with 2 hard disk drives do they have that SSD as Flash support for 1TB Drive or it is separate drive for system. Thank you a lot !
OK i buy for that AIO Lenovo that NVMe storage : www.tomshardware.co.uk/hp-ex900-ssd,review-34344.html // www.amazon.com/HP-EX900-Internal-2YY43AA-ABC/dp/B07B319VG2 // Working without problems. That HP EX900 have PCI-E Gen3 x4 interface... I do some Read test and memory shows 1700 around... not working same good with mixed data. I'm mean not keeping so high speed, but that is memory not motherboard. Regards. PS. PC now working as should :)
no existe ningun metodo bien explicado para abrir ese tipo de PC , intentarlo es Romperlo , ya me paso por eso les digo no lo intenteis ni por broma !!! , incluso los mejores tecnicos tiene miedo abrir esa maquina
Why you people add these annoying music to your YT videos, it ruins the videos totally. Also a suggestion is to edit the videos so people don't need to watch you take off the screws for 2 minutes
Thanks so much man, it took me a good two days to figure out how to get this rear cover off and I couldn't figure out what I was doing wrong. But I followed what you did and it finally worked. Obviously you have make sure you have the screen laid down on something soft like a bed or a towel or something to make sure it doesn't get scratched and make sure you don't use a knife or anything to wedge the screen out, I just ended up using a flathead screwdriver to hold part of the left part of the bottom part up, then I slid the guitar pick up and down the gap between the screen and the frame, then wiggled it up and until it finally clicked and the screen on the that side came loose, then I did the same for the rest of the screen and finally got it off.
Finalmente me decidí a desmontar el mio un Lenovo AIO 520 24ast (24 pulgadas) para meterle 4gb más de ram y un ssd de 240gb nmve.
Pues ya que se me ha ayudado, lo correcto es que comenté en indique aquí como fue el proceso.
La referencia fue este vídeo, el cual seguí casi al 100%
El video oficial de lenovo no sirve de mucho, no es tan fácil como lo pintan ahí.
No es fácil, no es como otros equipos, quitar tornillos y listo. La carcasa está ajustada al panel como por unos remaches que hacen que esté perfectamente encajada y es complicado quitarla. Describo los pasos que seguí yo:
Consideraciones iniciales:
- Abstenerse si no se esta habituado a desmontar equipos, no es nada fácil y es muy delicado
- Nunca forzar nada, con paciencia y firmeza, no a lo bruto
- Adquirir herramientas específicas para desmontar, más que nada hace falta una cuchilla, paleta fina y firme ya que el hueco para introducila es inexistente. En mi caso use una herramienta de apertura/paleta GB-5A, comprada por 1 euro.
- Dejar la peana puesta, ya que esto nos permite descansar, y apoyar normalmente el equipo mientras se manipula. Además al poner los módulo podemos encender el equipo aun desmontado para verificar que todo esta bien antes de cerrarlo.
- Hacer el proceso poniendo cartones o algo blando de debajo. En mi caso use un sofá antiguo como mesa, así el panel no sufre daños al estar manipulando los bordes.
Proceso:
1) Quitar tapa trasera que rodena la peana y tornillos, sencillo.
2) Primer problema, al quitar la tapa y tornillos anterior nada sucede, hay que meter una herramienta tipo cuchilla (GB-5A) muy fina en la parte inferior, entre el panel y la carcasa e ir pasandola de un lado a otro hasta que se va separnado la carcasa del panel por abajo, partiendo de la zona donde no está el tornillo inferior. Al principio cuesta meter la cuchilla entre panel y carcasa, pero una vez metida con cuidado la vamos paseando suvamente hacia el otro lado hasta que se vaya abriendo un pequeño hueco.
3) Nuevo problema. Al girar el tornillo de la parte inferior este esta duro, no hace nada. Debe ser como un resorte, no es un tornillo en sí. El truco es despues del paso 2 (y como se ve en el vídeo), dejar la herramienta metida en esa zona haciendo palanca, mientras se gira el tornillo insistentemente, llega un momento que 'salta algo' y sale ya buena parte del panel por su parte inferior.
4) Con la herramienta indicada, la introducimos ahora por un lateral y la vamos pasando de abajo - arriba varias veces, parece que no pasa nada pero al cabo de unas pasadas notamos con 'salta' una zona de la pantalla, como si se soltar de una presilla o algo así, seguimos con insistiendo hasta que salte todo el lateral, al acabar vamos al otro lado y cuando parece que ya está hay que hacer lo mismo en la parte superior, ..., el panel está como pegado a los bordes. Ojo aquí no ser bruto porque como metemos y hacemos palanca con el panel podemos cascarlo.
5) Una vez salga todo el panel hay cable que va del panel a la placa que hay que quitarlo de unas presillas, no hace falta desconectarlo que es bastante largo, además así podemos encender el equipo para probar antes de montar de nuevo.
6) A partir de aquí ya es más sencillo y más estándar, pese a que mi placa no es exacta al video es poner la ram en su sitio y el ssd nvme en el suyo (el tornillo en mi caso ya venía puesto).
7) Una vez puesto y probado, montar de nuevo que es muy sencillo, con las manos acercamos el panel a la carcasa y con una suave presión ya oimos 'clacs' en varias zonas de que se encaja de nuevo. Montarlo es coser y cantar.
Y eso es todo. La verdad es que es lamentable que un equipo como este sea tan complicado de desmontar, nunca había visto un pc tan complicado en ese sentido, pero con paciencia y sentido común se consigue. Insisto en mirar el video con detalle, ya que fue mi referencia y me sirvió de mucho.
Cuanta ram tenia instalada de base amigo....?
excelente amigo este vídeo y tu aporte me servirán para realizar el proceso, una pregunta tu le pusiste un disco de estado solido, se lo adicionaste? o le remplazaste el que ya tenia?
@@alextgsrr71 En mi caso no tenía ssd, le puse uno de 256 de la marca yucun.
@@musicaCulta ahora la pregunta mas tecnica le colocaste M2 Sata o M2 PCIe?
@@alextgsrr71 Por lo que yo sé y al menos el 24AST no admite ssd m2 Sata, ha de ser m2 pcie nvme, este es el que yo compré:
YUCUN 240GB SSD M.2 2280 PCIe Express GEN3.0x4 NVMe
www.amazon.es/gp/product/B07HVSF68X/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1
It's an excellent guide video, I recommend you follow it to open your AIO. A TIP: Use a credit card or thin plastic to open the AIO, it worked for me.
Thank you for a great video. I also cracked my screen and destroyed mine. Be aware this one breaks supper easy. Good luck everyone. This video is the best I have seen and I broke mine anyway. Do not blame this man who gave us the video blame Lenovo and the design.
I also broke
Me too
Also mine what the f!!!
DON't DO THIS AT HOME!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! MY SCREEN BROKE!!!
I also broke mine, this lenovo engrs do not think the design. So complicated to upgrade.
It was very helpful for me as I had problem with dismantling my AIO 520-24 AST for installing SSD drive. It's not so easy when you do not know where to push...
I've seen the cracked screen commentaries and all I can say is - I followed the steps and had no problems. This person makes this look fast and easy and I think that's what's tripping people up. This is someone working with a practiced hand - most of us are doing this for the first time. Go SUPER slow, be extra careful, watch the video 3 times before you start, pause the vid and do each step really slowly. The plastic casing is gonna make a shitton of horrific I-sound-like-i'm-coming-apart sounds - focus on not torqueing the screen and don't worry about the plastic complaining and you should be good.
So first you have to unscrew the 2 or 4 screws under the cover of the stand, then plug out a bit of the side plastic mounts, and then screw the botton frame screw. Yet, even after that, I cant seem to pull the screen off. Frustrating.
Para aquellos que tengan problemas con la pantalla (muestra lineas horizontales y se congela la pantalla y no responde el teclado ni el mouse), hay que limpiar la memoria y cambiarla de banco y listo
Thanks for posting this video. I just needed to take the damn thing apart so I could fix it, but wasn't sure how. Much appreciated.
Very helpful I opened 4 units to upgrade the ram. But RAM slot is designed at awkward place. Yeah for first time it took Lil extra time.
Where did you get the ram?
Mantap.. ini dia yg saya butuhkan.. thank you..
You opened that up roughly but safely. I tried opening it even gentler and ended up separating the dark screen which is glued ON from the digitizer behind it. The computer would not separate along the side or top enough and my plastic tools didn't help. A word to the wise, be aware this is a hard case to open.
I have another new 520 and I WON'T be opening that one EVER.
don't do it yourself!!!!!!! My screen also separated! Don't do this at home!!!!!!
Wouldn;t you know it, 3 years later and I have to open another 520 which is giving me hell. It separates but refuses to come off clean, hanging onto to every tiny plastic tab and then some. What a pain. It really didn't need to be like this. It isn't Fort Knox. Still don't have it opened fully.
Never try to open this computer, it is very delicate and the screen can break very easily.
Wish I'd read this first.
This is an easy fix, nothing much to break and despite the comment above, it isn't easy to break...
@@chrisdawes7270 yeah
Not that easy guys. I just lost my lcd panel
I managed it just fine without breaking it, it was still a pain in the arse and took ages to figure it out but you've got to make sure you don't force anything where it's not meant to be forced and make sure you used anything sharp in between the screen and the frame.
I have a v530 with i3 processor. what cpu does it support as an upgrade ?
why always the very annoying, loud music to accompany these videos? Grrrr
Tengo el mismo PC, ¿ le puedo cambiar el disco duro mecanico a un disco Solido?
Terimakasih 🙏
Thanks. Very useful. Just upgraded my RAM to 12GB. BTW, you don't need to pull out the connections. The RAM can be easily updated without doing that. Just remove the circular stand and it opens up totally.
are you replacing the old ram with the new one or adding one? I am totally unaccustomed with PC parts and upgrades.
@@azzurri1402 Added additional RAM
Which of the circular stands are you referring to, because adding an additional ram is what i'll need instead of cracking my screen. Cheers
@@deinbobriggs6235 The base stand on the PC.
@@deinbobriggs6235 It wasn't too difficult to install the RAM. Opened easier than I thought.
Like so many other comments on here, I did this as carefully as possible, and the screen still cracked. I wish I'd read the comments beforehand :-(
Donde consigo el reemplazo de esa pantalla?? Yo también la rompí abriendo y no es mío, ayuda por favor.
@@stevengarcia9882 It has been a long time since I ordered mine, but if you Google LM238WF2 I think that was the (non touch) screen that I ordered. There should be some available to buy on eBay etc.
DON"T DO THIS AT HOME!!!!!!!!!!!!!!!!!!!! SREEN BROKE!!!!
Hi i am thinking about replacing hard drive with ssd. Is it normal 3.5 inch hard drive.
I have the same AIO and I hate the noise of the cooling fan. Do you think that if I open it like this video, I could switch the fan to a quiet one?
Just throttle the cpu to 95% power.
can u suggest recomendation ram brand, speed ? is it sodimm?
In order not to brake the screen, follow the instruction laid down in the file "ideacentre_520-22-24_hmm_20180614.pdf". You can find this guide using Google. No sharp tools for detaching side and upper side of the screen!
Thank you
Gracias
After my experience today, I would not advise doing this. I cracked the screen despite being as careful as I could. Take your pc to an "expert" so that if they break the screen, it is their fault.
same here, display just cracked without reason
uhhh im not sure your supposed to crack the screen. worked well for me. maybe try laying the monitor on a flat suface and make it facing the surface without your impaling yourself with the suport rod thing
Or maybe Lenovo should come up with a better design. A new screen is over £300.
@@grantwallace1882 I broke a screen on and we wont work on them any longer.
DON"T DO THIS AT HOME!!!!!!!!!!!!!!!!!!!!!!! BROKE MY SCREEN!!!!!!
useful video. Thank you
hello, thanks for the video. also i want to remind you that you've forgot to mention the authors of the song you use. youtube sometimes delete account for that.
nice job man
it's very help full
bang pc aio ini kl dibanding ama aio 510 bagus mana ya?? maklum nubi hehehe
I broke my lcd of Aio 520. Can anybody help to get a replacement lcd. The cost etc.
Hi.. What ram size does it accepts/use? Is it tge regular ram or the laptop ram?
Laptop ram - DDR4
manta sekali
Thanks for the vid but ****WARNING****. I have dealt with all-in-ones for years but this one is a nightmare. The screen cracked and I had to spend a couple of hundred pounds to replace it for my customer. I will not be dealing with this model again...
It is a bad order. First you have to turn the screw, then you can use something like a spatula to separete the screen from base.
visipro 4gb ddr4 itu PC brp suhu ?? hasil setelah dipasang gimana tuh, retak gak LCD nya ?
I cannot loosen the screw! It is too tight. I know I'm supposed to turn it to the right but it won't budge. I'm in danger of ruining the thread on the screw. Any tips on loosening it?
Ok I sussed it. Required better screw driver and more brute force. I would recommend using a credit card to slide round edges of screen rather than a screwdriver. Easily the hardest case ive had to open especially with the high risk of damage!!
No its to the left
lefty loosey righty tighty
thanksssss
So should i do this because im kind of afraid of cracking/breaking the screen
DONT OPEN
Lenovo engrs should think the design of the casing, i broke the screen si dis appointed since the cost of the replacement is so expensive.
Do you know if that stand can be removed?
yeah it can be removed. just flip your pc with the monitor on a flat surface and under the stand there should be a screw. using either your thumbs or a screwdriver just unscrew it off and there you go (you might also have to take off the cable management thing shaped like a 9 if that helps).
CUAL ES EL MODELO O CODIGO DEL BOARD ?
tried to open one of these, 2 hours, careful
the screen always in tension, almost break fuck lenovo and this design aint gambling a new screen
(25+ years of computer building/laptopr repair experience)
Kalo tambah SSD bisa gak yah gan?
Bang maaf mau tanya,
Itu Ram yang bawaannya dari pabrik On Board kah atau gak???
Trus untuk yg Upgradenya ada Slotnya sendiri khan itu yah??
Mohon bantu dijawab yah bang segera 🙏🙏
Quiero reinstalar w10 pero al iniciar la instalación aparece el logo de Windows 10 y se reinicia. En legacy y uefi hace lo mismo. Me ayudan?
hay que actualizar la bios
Tengo una de esas con 16Gb de ram y un amd ryzen 3 3200GE
I will try to open mine in a week... I have to grow that kind of fingrnails
U did it?
u did it?
@@natt3965 yes! But I painfully broke my nail.
@@natt3965 I definetly recomend not to use metal tools to prevent damage to the plastic case, instead use rígid plastic tools
can you tell me the ram speed on stock ram?
after you upgrade does that run on dual channel?
2400mhz or run cpuz
Don't do it!!! I didn't crack the screen but the screen never worked again.
for doing this I messed up my screen where I get another screen
How to upgrade graphics card?
Ram bawaannya taman atau bisa dilepas ya bang?
No need to open the top of this machine to insert ram, open bottom only by pulling it away from the case, then pop off metal access panel at top right, the insert ram... done.
This video does it the hard way.
can you provide more instructions? how does the bottom part come off?
Buen día a todos, si alguien tiene problemas para formatear una PC como la Ideacentre AIO 520-22AST o similares, ya sea con el sistema operativo Windows 10 20H2 en adelante, si la computadora se les reinicia al iniciar con el medio de instalación o USB de Windows, deben de actualizar la BIOS de la PC para que pueda funcionar bien la instalación con versiones más recientes de Windows 10, otra alternativa también es instalar una versión de Windows 10 anterior, como la 1909, por alguna extraña razón éste tipo de computadoras ideacentre no funcionan bien con nuevas versiones de Windows 10 como la 22H2 que es la más reciente, así que actualizando la BIOS debería de funcionar, además de usar su unidad de instalación de Windows en UEFI, si actualizan la BIOS de la computadora, tenga cuidado, ya que si se apaga la computadora si se va la electricidad, quedará inservible la computadora y tendrán que reprogramar la BIOS lo cual puede ser costoso
Good morning everyone, if anyone has problems formatting a PC like the Ideacentre AIO 520-22AST or similar, either with the Windows 10 20H2 operating system onwards, if the computer restarts when starting with the installation media or USB of Windows, they must update the BIOS of the PC so that the installation with more recent versions of Windows 10 can work well, another alternative is also to install a previous version of Windows 10, such as 1909, for some strange reason this type of computer ideacentre don't work well with newer versions of Windows 10 like 22H2 which is the most recent, so updating the BIOS should work, as well as using your Windows installation drive in UEFI, if you update the computer's BIOS, be careful , since if the computer is turned off if the electricity goes out, the computer will be unusable and they will have to reprogram the BIOS which can be expensive
please give alink to buy this ram
Bang mau tanya. Tahap awal kok tinggal pencet aja sih?? Punya saya dipencet ga bisa, di cungkil juga ga bisa. Apa harus lepas kaki Bawah (yg bulat) dulu ya???? Mohon direspon🙏🙏🙏
Ya harus lepas kaki bawah dulu.
Thanks for the review. Sorry if this's too late, but is the GPU upgradable? I searched far and wide but didn't find any relevant info. Can you confirm or deny, and if so what form factor should I look for? Thais in advance.
Did ufind it
@@abhijeetkatiyar7209 unfortunately no, I found out the GPU isn't upgradable, but tbh it isn't a big deal now that I've spent enough time on this desktop and came to know what it actually is, and is not, meant for.
mengikuti tutotial ini menghasilkan panel LED saya pecah ! mungkin sebaiknya ditambahkan keterangan suara maupun tulisan mengenai beberap bagian yang harus hati - hati.. soalnya kalau ngikutin di video kayanya enak sekali bongkar bongkar pas bagian layarnya, hiks hiks..
Boleh share om itu pecahnya gara2 pas apa ya? Koq di atas jg byk yg pd pecah screennya... Mau ikutan bongkar jd ngeri duluan... 😂
Slot ramnya ada brp gan?
@@dennytribudiprasetiya5431 cuman 2, bawaannya bisa dilepas
Some scaremongering going on here! Yes the 520 is a fiddly little wotnot to open BUT WITH CARE it pops open after some delicate patience. I've opened mine twice now without incident. The only bummer is you cannot fit a standard 2.5in SSD with adaptor bracket. The mounting bracket for the 3.5HDD is bespoke and will not accept the adaptor sufficiently well so be prepared for some metal work unless you install a m.2 SSD.
does it have a connection for M.2 SSD?
@@mariush573 Some do, some don't. Check the specs for your specific machine with Lenovo.
Please who can help me I opened my device to clean it with air but after turning it on the picture is not like before. Lenovo logo is not clear and the blue screen look like purple or. Pink screen
Ok so where do i buy a cheap aftermarket replacement screen at now... smh
Legend says he cut his finger with that knife not soon after
Buen dia, Cuantas bahias de memoria tiene. Y trabaja con DDR4 o DDR3, o ambas? Rene, Bog, Col. Gracias.
How many ram bays do you have? Does it work with DDR3 or DDR4 or both? my email is cafeinternet_y@hotmail.com, thanks.
Trabaja con DDr4 y cuenta con dos bancos de memoria ram!!
@@cabarrer cuanto se puede expandir de ram 16gb?
@@alanpinto8153 2 x 8 si te recibe las 16
@@cabarrer
Puedes incluso poner una de 8GB y la que trae por default de 4GB?
never try to open this machine , even my screen is broken , any one help me where i will get this screen
protech azimee The screen will run you about $200
Need a replacement. Can anyone help
Thank you mate..... It be helpfull very.... One question.. I opened and now i want to install extra M.2 SSD 128GB or 256GB - the question is : How it works that extra drive? Is it be as second drive in "My Computer" then i will install there separate System or it just work as Flash memory to speed up our 1TB disk ? In AMD StoreMI technology? Then i will buy only small 128GB. But i would like to buy 256GB install there all System Files and keep picture, and that 1TB Setup as second Quiet (power off set after 5min). Can you please answer for that question please.... we have so less options here in BIOS i wondering maybe lenovo just block the way how we can use it.
did you open this pc? it has a connection for M.2 SSD?
@@mariush573 nope. only sata
Bang, buka jasa pasang RAM ga? Pgn upgrade RAM PC kantor yg sama seri 520 juga
Buka.
i tried but cracked the screen
me too :(
same here, rly shit AIO for repair
bang tanya itu pcnya ada slot ssd m.2 ngga? makasih
Kyaknya gk ada gan
Does anyone know what is the maximum capacity of RAM we can upgrade this PC
8GB
@@jakubgasparik8021 you sure?
This pc have like 4 or five models. Some jabe ebetter processors or integrated graphics. This is a lpw end pc . I was upgrading ram too from 4GB to 12GB . But i think 8GB is the sweet spot for every model. Tell me the cost of ur pc and i'll recomend better. Sry for bad eng
@@jakubgasparik8021 12g is the most I can give?
@@simpteamsix you can go more but tell me the cost of ur pc
Slot RAM nya 2 ya?
toko dimana gan? bisa upgrade punya saya ga
Di banda aceh gan.
ทำไมคุณไม่คว่ำหน้าจอกับพื้นโต๊ะล่ะ
can we put 8gb ram on it?
comes with 8GB ram i think
well i have the edition with the AMD Ryzen 5 processor with Vega 11 graphics so it might differ on your model
yes, you can
m.2 port have?
@@bootlegscarce0844 i want to buy M.2 SSD for my Lenovo AIO 520 24ARR which i just opened. My question is... because Lenovo set up 128GB SSD + 1TB 7200rpm usuall... how they did that. Is it working as 2 separate storage or as one (like FusionDrive where 128GB be used as FlashMemory for basic drive using for example AMD StoreMI technology). In normal desktop i will set up as i want, but because here is no any options in BIOS i wondering it may work just in one way. My idee is to buy 256GB, install there system and keep necesary files, and 1TB just leave for videos (and set up power off for this drive after 5min to don't listen any noise). Can you please give my advice if you know anybody who using AIO PC with 2 hard disk drives do they have that SSD as Flash support for 1TB Drive or it is separate drive for system. Thank you a lot !
OK i buy for that AIO Lenovo that NVMe storage : www.tomshardware.co.uk/hp-ex900-ssd,review-34344.html // www.amazon.com/HP-EX900-Internal-2YY43AA-ABC/dp/B07B319VG2 // Working without problems. That HP EX900 have PCI-E Gen3 x4 interface... I do some Read test and memory shows 1700 around... not working same good with mixed data. I'm mean not keeping so high speed, but that is memory not motherboard. Regards. PS. PC now working as should :)
Ini ada slot SSD nya bang?
Kemungkinan ada gan
@@AzmiH ini masih pakai hardisk yg besar ya? Yg 3.5?
@@fandydawenan ya betul masih pakek hdd 3.5"
Wrong procedure to remove stand
Ramnya DDR brp?
DDR 4 gan
DDR4 gan
no existe ningun metodo bien explicado para abrir ese tipo de PC , intentarlo es Romperlo , ya me paso por eso les digo no lo intenteis ni por broma !!! , incluso los mejores tecnicos tiene miedo abrir esa maquina
The worst thing about the video is the music.
totally wrong method
what's the correct method?
Lokasi bengkel dimana gan?
??????????? This isn´t Mordor, pls write in single human (?
Why you people add these annoying music to your YT videos, it ruins the videos totally. Also a suggestion is to edit the videos so people don't need to watch you take off the screws for 2 minutes
All this just to do RAM upgrades?
Trash design :(