how come when I try to draw my graph uses huge units like when I type 30 I get a tiny line but when you do it you get a big one and im on the same zoom
hello. thank you very much for the lessens. were an very helpful. my question is, can i use auto cad 2017 for create furniture like cabinets, wear drops etc?
Hello anyone who was having a problem with not being able to draw a door or window to the wall of the house, please press F6 and your dynamic UCS should come on to let you do it.
Yeah, i can't get past making the door. I'm not sure why, but when i create it, it goes up the Y axis instead of the Z axis. It is so frustrating trying to figure out how to fix this.
Make sure you are on the right surface. It will light up if you are. If you are having trouble try drawing it from an edge and then moving it use the MOVE command.
+Jordan Hargraves did you have to use a mouse on this? I'm using the mouse pad on a laptop also and I've having the same problem. I also tried using a mouse but it didn't work either.
I wanted to know is this worth taking for summer school? It's either Auto Cad or Mathematics so I could transfer in the winter(quarter system)/spring semester
Everything was going fine until I tried to draw the door @ 8:43. If I click the bottom line of the building pad to start the door, it draws it on the X,Y plane, or across the floor. In order to draw it vertically, or on the wall, I have to click the top line of the building pad. What is going wrong? When you drew it, you mentioned there's a little green tool of some kind. I can't see it in the vid. Are you referring to a snap tool of some kind? I have snaps on, with active snaps being Nearest, Perp, Endpoint, Midpoint, Center, Quadrant, Midpoint and Extension. I guess I can draw the door starting from the top of the building pad and then just move it down 1 unit but that takes an extra step and the whole objective for me is to learn how to take extra steps out of the drafting process. Thanks.
i might have found your problem brother, press F3, it will be your snap cursor. if your still having trouble look at your bottom right toolbar you will see a square with a green dot, unclick that and youll be able too draw your door with out it snaping to the X,Y
moi non plus ca n a pas fonctionné on a pas exactement les meme command bizarrement, moi j ai refais une Ligne un peu plus grande et un PEdit pour joindre
so another question. tried drawing in the door but whenever i try starting from the base it automatically snaps to one the corners of the house. is there a setting im suppose to turn off
might have found your problem brother, press F3, it will be your snap cursor. if your still having trouble look at your bottom right toolbar you will see a square with a green dot, unclick that and youll be able too draw your door with out it snaping to the X,Y
I would like to ask I m using mac 2016 version and , shift key doesn't work .Is it i did something wrong or there is any key for rotate functions ? thanks!!!
Im using 2006 autocad and just switched to 2017 and its mind blowing how they almost kept it same and simple
how come when I try to draw my graph uses huge units like when I type 30 I get a tiny line but when you do it you get a big one and im on the same zoom
To be able to draw the door you need to open the 3D status bar and activate "allow dynamic UCS". Took med 30 minutes to find it....
oh jacob thank you!
Thanks Kristo Suur
Thanks dude! Your tutorials are awesome :)
Great tutorial, many thanks :)
how do you draw on the z axis... i cant draw the door
good vid :) you earned a new sub!
Stumbled across this video man this took me back 5 ish years to high-school
hello. thank you very much for the lessens. were an very helpful. my question is, can i use auto cad 2017 for create furniture like cabinets, wear drops etc?
Hello anyone who was having a problem with not being able to draw a door or window to the wall of the house, please press F6 and your dynamic UCS should come on to let you do it.
Thanks :)
Really good teacher
Very helpful i subbed!
Thanks! This is a big help.
Fantastic video man. Thank you
Yeah, i can't get past making the door. I'm not sure why, but when i create it,
it goes up the Y axis instead of the Z axis. It is so frustrating trying to figure
out how to fix this.
Great
This would be a brilliant tutorial if the door thing would work. everytime I try to draw it it just goes all over the shop!
Make sure you are on the right surface. It will light up if you are. If you are having trouble try drawing it from an edge and then moving it use the MOVE command.
nice :) love it
so when I hold shift like you say it doesnt actually rotate. it just does the line selection thing
shift and move your mouse while pressing the scroll button down, its kinda confusing
+Trent unknown oh thanks. i figured that would be the case. was soing this just using the mouse pad on a laptop
+Jordan Hargraves did you have to use a mouse on this? I'm using the mouse pad on a laptop also and I've having the same problem. I also tried using a mouse but it didn't work either.
Nice. Thank you
Wonderful
This says 2017 but the video refers to 2016.. ?
I wanted to know is this worth taking for summer school? It's either Auto Cad or Mathematics so I could transfer in the winter(quarter system)/spring semester
I've used this a lot more than I've use all the math I've learned.
how come when I draw the door the door went to the side of the wall?
Everything was going fine until I tried to draw the door @ 8:43. If I click the bottom line of the building pad to start the door, it draws it on the X,Y plane, or across the floor. In order to draw it vertically, or on the wall, I have to click the top line of the building pad. What is going wrong? When you drew it, you mentioned there's a little green tool of some kind. I can't see it in the vid. Are you referring to a snap tool of some kind? I have snaps on, with active snaps being Nearest, Perp, Endpoint, Midpoint, Center, Quadrant, Midpoint and Extension.
I guess I can draw the door starting from the top of the building pad and then just move it down 1 unit but that takes an extra step and the whole objective for me is to learn how to take extra steps out of the drafting process.
Thanks.
i might have found your problem brother, press F3, it will be your snap cursor. if your still having trouble look at your bottom right toolbar you will see a square with a green dot, unclick that and youll be able too draw your door with out it snaping to the X,Y
i tried it and it still doesn't work...:(
thanx really worked for me
Thank you so much, it worked
whoaa, thanks i have the same problem
Hello, I can't make the "offset", it's isn't working, but I don't understand why. Could you help me please? (Sorry for my english, i'm french)
moi non plus ca n a pas fonctionné on a pas exactement les meme command bizarrement, moi j ai refais une Ligne un peu plus grande et un PEdit pour joindre
DECALER in french autocad
so another question. tried drawing in the door but whenever i try starting from the base it automatically snaps to one the corners of the house. is there a setting im suppose to turn off
might have found your problem brother, press F3, it will be your snap cursor. if your still having trouble look at your bottom right toolbar you will see a square with a green dot, unclick that and youll be able too draw your door with out it snaping to the X,Y
thanks sir very hlp fl
not working with the offset and there are different units on my auto cad compare with yours.
I would like to ask I m using mac 2016 version and , shift key doesn't work .Is it i did something wrong or there is any key for rotate functions ? thanks!!!
What unit am I supposed to set it to? Mine is on millimeter
If you're not from USA metric if you are from USA then inch
Or if your from USA and want it to make more sense, metric.
The polyline ruined everything. I couldn't extrude upward because autocad didn't like the polyline
Not working for me as worked for you.
not working with the offset and there are different units on my auto cad compare with yours.
DECALER in french autocad