Honeywell 5800PIR-RES: Programming to a L5100 Wireless Security System
Vložit
- čas přidán 1. 03. 2013
- The 5800PIR-RES is Honeywell's most popular wireless motion detector. As an effective deterrent against thieves who enter your empty house by breaking into or crawling through vulnerable, open windows, the motion detector provides an extra layer of security to ensure that your home is effectively protected against even the most clever thieves. In this video, Sterling shows users how to program the 5800PIR-RES into a Honeywell LYNX Touch L5100 wireless security system.
FEATURED PRODUCTS
Honeywell 5800PIR-RES: alrm.gd/honeywell-5800pir-res
Honeywell L5100: alrm.gd/honeywell-l5100 - Jak na to + styl
My motion sensor doesn't trip the alarm. It's set to interior with delay, but it doesn't seem to work. I did a walk-test and it picked up my motions. Can you tell me what might be the problem?
Hi
How to program Linear GD00Z-2 is a garage door opener remote command transceiver with built-in Z-Wave technology.
got a stupid question, why would you use installer lock out feature. I would not sell this device because, if my installer selects that, there's no re-entry to system programming.... side note* stupid the way Honeywell put it in like that, its always been an option, but much harder to make that mistake in previous versions.
How about a DT900 with Hardwire to wireless conversion?
How can i get My master code whit out a provider number In The house did i Live os a alarm system And i want to make it works
Spylahbaby C The motion sensor is a wireless sensor, so it doesn't trip for 3 minutes so it can save battery life.
Thanks for the helpful tip Hunter!
Sterling Donnelly What a apart alarm! extension speaker gets 60th than the rosshini and gent 2511
My dog is about 50 pounds and 18 inches tall. Will she set off the motion detector if set to alarm away?
Carl Parj The motion detector should ignore a dog of that size. You should avoid having any furniture that the dog can jump on within 6' of the motion however.
Sterling Donnelly gent 2511 and rosshini...
can it be used outside? like in a balcony, but when arm stay the 5800PIR-RES is working not off like the ones inside.
It is not designed for outside use. The 5800PIR-OD (www.alarmgrid.com/products/honeywell-5800pir-od) is the outdoor rated Honeywell wireless motion detector.
Sterling Donnelly ok, so I can program it as a perimeter in the response type and it will be working when arm stay?
Yes, you can program it like a door or window to have it armed in both Away and Stay.
thank you !!!
Sterling Donnelly How many fire alarm did you have?
Hi, I have both of the unit 5800PIR-RES and L5100. However the 5800PIR-RES battery went dead/low prematurely twice within 12 months of usage. Is this due to the PIR settings which may detect the motion too often?
+Eddy Ann Yes, the lifespan of the battery will be affected by the way the motion is programmed. How do you have that zone configured now?
+Sterling Donnelly ok the pir settings are as follows
Loop number 1
Device type :motion sensor
Response type :interior follower
Alarm report :yes
Chime: no
Supervision :supervised
The sensor trigger when armed but not armed stay. But during disarm, once in a while it sense when there is a motion/activity which trigger the lynx yellow status for a while (2-3 seconds). I thought it wont trigger anything during disarm?
+Eddy Ann None of those settings seem like they are unusual or would be causing the battery to drain prematurely.
Is the yellow status a fault or a trouble when it pops up?
+Sterling Donnelly the yellow status is the same like those window/door sensor (when open) with some green led flashing. After a while it entered green status again after 2-3 seconds. It just that it sense/trigger/detect the motion when disarm.
+Frank Longo Ya, so it sounds like your motions are programmed and functioning properly so did you perhaps get the batteries from the same package/source? Maybe you just got unlucky and got two bad batteries.
HMMM