So simple, even us sales guys can do it! Thank you guys for always taking user-friendliness into account with your software, on top of building fantastic products across the lineup!
I just installed the M8.14 and M1D in my Stinger with the Maestro AR interface only to learn that Accordo is not yet available for my situation. I had to laugh when I watched this whole video again - this time to the very end - to find that I am not losing it! Any timeline on when it will become available for the Maestro AR folks? Thanks
Dear Rober, Thank you for reaching out. Currently, there is no official release date for compatibility with Maestro AR, but please be assured that the Audison R&D team is actively working on this integration. We apologize for the inconvenience this may have caused and appreciate your patience. Best regards, Audison team
In addition to the comment from @PatrickKlinge-fu2tm, if you are using the Maestro AR interface in your application, Accordo is not yet available as of August 11, 2024.
I'm unable to get the accordo output level calibration signal into the green level even with the volume set to +6db and the minidsp calibrated mic setting at maximum in the windows settings. I'm stuck on signal low and unable to progress to the next step.
has any one tried accordo yet and having issues? i get to the end of the wizard (where it counts down before it starts taking its measurements) and the whole program (bit drive) closes. I'm using a Dayton audio umm-6 mic
Dear Andru, Thank you for reaching out. We recommend downloading the latest software release for bit Drive 2.0.1.0 from our support page: audison.com/support/software-firmware/. This release addresses compatibility issues with the Dayton Audio UMM-6 microphone. We hope this resolves the problem you’ve encountered. If you have any further questions or issues, please let us know. Best regards, Audison team
Known issue. Solution is on youtube, need to search for it. Try to switch off music front head unit and do update with main power only. It worked for me at the end search for "Audison Forza Firmware Update 1.0.7.33 fails with "flash update error" (Fix in the description!)"
So simple, even us sales guys can do it! Thank you guys for always taking user-friendliness into account with your software, on top of building fantastic products across the lineup!
I just installed the M8.14 and M1D in my Stinger with the Maestro AR interface only to learn that Accordo is not yet available for my situation. I had to laugh when I watched this whole video again - this time to the very end - to find that I am not losing it! Any timeline on when it will become available for the Maestro AR folks? Thanks
Dear Rober,
Thank you for reaching out. Currently, there is no official release date for compatibility with Maestro AR, but please be assured that the Audison R&D team is actively working on this integration. We apologize for the inconvenience this may have caused and appreciate your patience.
Best regards,
Audison team
🎉🎉🎉🎉🎉🎉
I have downloaded it but the accordo isnt on there when i click on the wizard?
The amp needs to be connected and fw up to date to 2.0 too.
In addition to the comment from @PatrickKlinge-fu2tm, if you are using the Maestro AR interface in your application, Accordo is not yet available as of August 11, 2024.
I'm unable to get the accordo output level calibration signal into the green level even with the volume set to +6db and the minidsp calibrated mic setting at maximum in the windows settings. I'm stuck on signal low and unable to progress to the next step.
Umik-1 !?
Open the case and set a proper gain for the mic with the dip switch
Umik-1 !?
Open the case and set a proper gain for the mic with the dip switch
@@PatrickKlinge-fu2tm Yes the Umik-1, its currently set to 18db - which gain would you recommend? Thank you!
@@dannymm depends on windows..
try it out (Y)
@@PatrickKlinge-fu2tm I've changed it to 24db and now its outputting the correct level and the Accordo tune completed successfully. Many thanks!
has any one tried accordo yet and having issues? i get to the end of the wizard (where it counts down before it starts taking its measurements) and the whole program (bit drive) closes.
I'm using a Dayton audio umm-6 mic
Dear Andru,
Thank you for reaching out. We recommend downloading the latest software release for bit Drive 2.0.1.0 from our support page: audison.com/support/software-firmware/. This release addresses compatibility issues with the Dayton Audio UMM-6 microphone.
We hope this resolves the problem you’ve encountered. If you have any further questions or issues, please let us know.
Best regards,
Audison team
@@AudisonItofficial i downloaded it a few weeks ago worked like a charm thank you 😁
Is anyone else getting a flash error when trying to update Forza firmware?
Please have a look at the manual for updating in rescue mode.
Yes, same Error. It doesent help to do the Update in Rescue mode!
@@ma.hy.793
check the usb cable and use no extension for the upgrade. Do it Exactly like explained in the Manual for the Rescue mode!
Known issue. Solution is on youtube, need to search for it.
Try to switch off music front head unit and do update with main power only. It worked for me at the end
search for "Audison Forza Firmware Update 1.0.7.33 fails with "flash update error" (Fix in the description!)"
Hello, please follow that procedure in that case. Thanks! audison.zendesk.com/hc/en-gb/articles/23302406960401-11-RESCUE-PROCEDURE