etrailer | LubriMatic Electrical Connector Dielectric Grease Review
Vložit
- čas přidán 30. 12. 2020
- Click for more info and reviews of this LubriMatic Trailer Wiring,Wiring:
www.etrailer.com/Accessories-...
Check out some similar Trailer Wiring,Wiring options:
www.etrailer.com/dept-pg-Acce...
www.etrailer.com
Don’t forget to subscribe!
/ etrailertv
Full transcript: www.etrailer.com/tv-review-lu...
Hi there, maintenance-oriented haulers today. Today we're going to be taking a look at Librimatic's Dielectric Contact Grease. So we've been experiencing some issues with our travel trailer here. When we plug in, sometimes our lights are working, sometimes they're not. It's a little bit finicky. If we jiggle the connector, it usually works.Most of the time, this is caused by poor contacts inside your connector and that's usually due to corrosion.
You can see here that this connector is actually got some corrosion on it. And the plastic's actually starting to deform because once you get this corrosion on here, it's possible that you can still have contact enough to eliminate your lights and operate your functions. But this corrosion is going to cause extra resistance here, which is going to cause it to build heat. And as it builds up heat, you can see the plastic's deformed due to the excessive heat that it's caused. And eventually over time, that heat is going to cause further damage and fretting onto our connectors here.
And eventually, it's going to get so bad that we're not even going to be able to fix it.So to get on top of this, before it gets that bad, we want to clean out all this corrosion and we want to seal it up to prevent it from happening again. And that's why we're going to be using the Dielectric Grease here. Now there's a lot of different ways you can clean out corrosion. Usually something acidic like vinegar and water mixture works great. Or you can just go to your automotive store and pick up electrical contact cleaner to clean it out.
You can also use a bristle brush to clean it out. But you do want to be careful when using any brushes down here because if you spread those contacts apart, you may spread them apart too far to where they're not going to touch onto the terminals once you plug it in and then you need to replace the pins, potentially the whole connector.So we're just going to spray our contact cleaner in here. And we're using this contact cleaner because it is a quick-dry contact solution. Because we don't want any moisture or anything left behind. This is designed to dry out very rapidly so we don't leave any moisture behind.So we use the contact cleaner.
We still got a little bit of corrosion in there. So we're going to take our bristle brush to clean that up. Now you'll notice I'm not sticking it down in there, we don't want to spread those terminals out. So we're just kind of rubbing it along the top to get that corrosion out of there. A toothbrush works very well as well, if you've got an old one laying around. But if you don't and you need a bristled rush, you can get one just like I got here at etrailer.com. And we're just trying to get all that out of there.Now that all of our contacts have been cleaned up, we're going to take the Dielectric Grease and we're going to apply it generously to all of our pins here. So we want to try to keep out any moisture from getting in there. And we're not just using any grease. We are using dielectric grease because dielectric grease is specifically designed for this application as it does not conduct electricity so we don't have to worry about any of our contacts shorting out between one another. And then it has the other properties that grease has where it coats up the surface and helps keep out moisture, sealing it all in. So now that we've got that done, we're ready to plug it in to our trailer and hit the road. And we don't need to clean any of this up, we can just leave it there. We're trying to seal out moisture and dirt.On the other side here on our truck, it's a good idea to clean these pins out as well. So we don't want to transfer any of the corrosion that may be on these or the other ones, back and forth. And we can also put the dielectric on these pins as well, to help further seal up and protect this side.Now that we've cleaned up each end and got them greased, we can go ahead and plug them together. Now we discussed earlier about how the grease is non-conductive because that's what we want. We don't want any of our pins to be shorting out with the other ones next to it. But that doesn't mean that it's going to cause any issues with the connections between our connector here on our trailer and the one on our truck, because the pins are designed to be a nice tight fit. So when it goes in, we do get metal to metal contact as it pushes that grease out of the way. Now it's when during cleaning, if you do stick something down
Thanks you the information.
You're welcome!
www.etrailer.com/Accessories-and-Parts/LubriMatic/11755.html
YOu should look up the meaning of Dielectric and do another vid.
Great video thank you.
Glad you liked it!
www.etrailer.com/Accessories-and-Parts/LubriMatic/11755.html
Great video, very helpful...⭐️
Glad it was helpful!
www.etrailer.com/Accessories-and-Parts/LubriMatic/11755.html
I understood that the grease does not conduct electricity, so it shouldn't be applied directly to the mating surfaces (pins and sockets) of an electrical connection
Yes it should.
Has anyone used the dielectric grease on their 30a / 50a power cord ?
That'll work just fine to keep moisture out of the connection!
www.etrailer.com/Accessories-and-Parts/LubriMatic/11755.html
It's not stated though I ass-u-me you'd want to disconnect the rig's batteries first?
You do not have to disconnect the battery before applying the Dielectric grease but you can if you so desire.
www.etrailer.com/Accessories-and-Parts/LubriMatic/11755.html
@@etrailer Step 1 of the directions on the can of CRC he is holding states. "1. Do not apply while equipment is energized." Also couldn't the use of a wire brush cause a possible short if the battery was still connected?
Ya why???
wrong application, not to be used on metal contacts
This is why the dislike button is important
That's an incorrect application of dieletric grease. Do NOT apply to the metal parts or the holes leading to the metal pieces. Only the plastic.
Make a video
You're wrong. The idea is to seal out moisture and dirt. This is why you're using a non-conductive material.
@@Sometimes_Always great idea. Smear a load of non conductive material between two surfaces which need to be in contact to conduct said electricity. Dielectric grease has its place but not in the volume and method shown in the video.
@@marcaustinI’ve been using it the ‘wrong’ way all these years and never had issues.
@@Sometimes_Always He's correct. You seal out moisture and dirt by applying it to the mating surfaces, not directly to the contacts of a connector that is connected and disconnected often. Another use case would be car battery terminals, where the connection is made and left alone. You would not apply this to the terminals until AFTER making your cable connections, ensuring the dielectric does not insulate your electrical path. SOURCE: AM ELECTRONICS MAN