BISSELL Power Force Helix Bagless Upright Vacuum 2191 Complete Disassembly, Cleaning, and Repair
Vložit
- čas přidán 13. 08. 2023
- In this video, we'll look at these three Bissell Powerforce Helix 2191U and 2191 Vacuum Cleaners I picked from the trash. We'll see what the common faults are as we completely disassemble and repair one of them.
SHOW YOUR SUPPORT
1: Become a Member on Locals: theguitologist.locals.com/
2: Donate via Paypal: paypal.me/guitologist?locale....
3: Buy Merch: bit.ly/GuitologistMerch
4: Send in Viewer Mail. (Contact Me for details at bradlinzy@gmail.com )
5: Purchase an ad! (Rate sheets available upon request at email above.)
6: Buy something from a sponsor and tell them I sent you.
7: Stand in the middle of the street naked screaming "LONG LIVE THE GUITOLOGIST!" Then when the cops arrive, tell them about my channel.
SUBSCRIBE TO CHANNEL 2: bit.ly/Guitologist2
#repair #restoration #vacuumcleaner
This has given me a sudden urge to take a look at my vacuum 😂. These fix it videos have been great. Thoroughly enjoying them!
This is a really great video, as I have a couple of factory refurb Bissels where replacement motors are unobtainium - and one is absurdly loud. I may need to get into there.
And for those watching, there have been several PC cleaning videos lately on other channels, where when compressed air was forced through the case fans, the fans spun so quickly that the motors burned up. I had no idea. So, it might be a good idea to not allow motors to spin too quickly when cleaning.
deep cleaned mine just now and forgot where that small circle filter went! thanks!
Brad, I found myself holding my breath watching you beat that filter. Ugghh.
I'm coughing just watching this
Best video I've seen on many home DYI repairs. Our Bissell just dead stopped. Broken wire exactly as in this video. Soldered up and runs again. The detail how all that parts disassemble is a huge help.
You have saved my sanity. I tore my vacuum apart because it kept kicking up dust when turned on (we stupidly used it to clean up plaster filth) and I couldn't find where the two rectangle filters went. I have been searching for nearly an hour for my model being torn apart so I could find it. Naturally it came off in one of the first steps so I had to disassemble the whole thing again, but at least the filters are in their proper place again. Thank you!
Thank you so much for this video dude. I was absolutely losing my mind. Trying to figure out what was wrong with this darn vacuum! Turns out it both needed the filter cleaned, and the belt needed to be replaced! You saved me a heck of a lot of money❤❤❤
Awesome! Glad I could be of help.
Reminds of some people that treat their vehicles the same way, never check the tires or fluids. They just put gas in and go. And then complain to high heaven 😜
I was thinking the same thing😂
Good eye spotting the broken wire on the brush. If only you had a vacuum to suck all of the crud out of the impeller... ;)
Amazing how my Bissell Powerforce Helix Turbo model 68C71 looks the same on the insides. The powerhead is exactly
the same design and plugs up ocassionally. It must be taken apart to clear out the rug pieces, hair and dirt debris. The
tower part has plenty of filtering and must be cleaned out with soap and water on the foam filters and let dry every time
unlike the ones you got there Brad which someone never did. Amazing how the motor housing was so dirty. My filtering
set up is designed differently in the tower section so that doesn't happen. Great job showing it working again Brad.
Thoroughly informative and enlightening Brad thanks for the content.
I need to go look at my vacuum.
That was fun thanks for pushing record :)
i have been using the shark machine for about 5 years now. i am impressed with their machine. i do have a bissell carpet shampoo machine it does a good job but i think it is a bit fragile , and could be built a bit better , thumbs up for the Fixologist
Brad just killed the grass under his fence.
Nice one Brad, long live my Henry hoover.
I need to clean the motor on mine! I never thought about doing that!
Crazy! I _just did_ finish the cleaning of my Bissell Powerforce! Nasty dusty dirty, I used a small car detailing brush to dig into the grooves behind the cannister. The filters were washable too. I think the *bag* type are a better cleaner design.
i hate the noise of a vacuum cleaner. i do have a carpet sweeper which isnt the same, but its nice and quiet and picks up a lot of dirt. this video reminded me i need to clean it out.
Wow that was caked! If this doesn't make people wanna clean theirs out too idk what will
I know, right?
Ty so much 😊
You’re welcome 😊
As a fellow human I am concerned about your lungs and urge you to wear a mask when dealing with these bacteria laden machines.Who knows what might be residing in those dust particles. Love the video and the insight it brings, we do need to learn more about the appliances we use, and it it begins with understanding how they work. Great sentiments, and the musical interlude didn't go un-noticed nor did the beautiful salvaged rug.
Just cleaned my shark vacuum filter, thanks.
The impeler nut is reverse thread.
That filter was "Caked"!
This is why Dyson's are actually worth it, very interesting engineering and much more healthy. Check them out!
My wife has a Dyson and I HATE that thing. The design of the wand is the worst POS I've ever laid hands on.
I can't even talk about my vacuuming issues lol
I'm gonna talk about them. Ok?
Nice music in this one.
1:14 I'm looking for the way to take apart that interior turbine for cleaning.
The metal fan case usually is just pressed onto the plastic housing, often getting a flat bladed screwdriver in between the edge of the metal fan case and the plastic housing will start to pry the cover off. Once the metal cover is removed you get full access to the impeller fan for cleaning it out. The nut holding the fan on may be a reverse threaded nut, holding the belt spindle with vice grips while undoing the nut should work, and the fan will remove.
The fans get clogged up like that if the vacuum has been used with the pre-motor filter not in place is someone has it out for cleaning and forgets to put it back in again, all the dirt will go straight from the cyclone separator in the dust cup into the motor fan, and the result is a clogged fan, no airflow through the fan and it overheats the motor. That overheat situation may be what caused the wire to the carbon brush holder to break, and rendered the machine unusable- probably for the best really as it would have had no suction at all in that state and would have continually tripped the thermal cutout.
The pre motor filtration is pretty poor on these, just a simple sponge filter is not really going to do much for stopping fine dust penetrating it, and the exhaust filter is non user accessible so once that gets clogged its going to cause repeated overheats of the motor.
Its almost as if Bissell designed it that way so the user would have to chuck it out and buy a new vacuum - built in obsolescence.
Drivebelts for the brushroll often stretch out over time, getting too slack to drive the brushroll once it encounters the resistance of carpet, and the brushroll will stall out with the belt simply slipping on the motor drive spindle.
You did a good job on that poor machine though, probably the most attention it's ever had in its life.
I hate these plastic vacuums lol.. Ive always used a Kirby. They last forever and have way way way more suction than anything on market besides like one other commercial floor cleaner lol.. fully adjustable height and auto transmission. You can buy a clapped out one used and rebuild em for cheap. Family member of mine threw away our G5 because they didnt understand how good it really was lol.. after breaking about 5 other crap ones I ended up getting another Kirby lol..they are tanks.
I left my mom's working Kirby behind after she passed in 2019. I don't have any rugs so I didn't need it. I tried for 30 days to give it a new home but nobody wanted it because "it's too heavy". She had all the attachments for it and never used 1 of them, just swept the carpets with it. The next occupant got it with the house.
I always clean my filters
Is that the new rug?
Decades ago, when I was a younger lad, I was asked to take a Rainbow Vac demo by a friend who'd get a discount on the one he was buying if I agreed. I had the demo guy come to the place where I worked which was an old print shop. The carpet in the front office was so bad that he refused to dirty his shiny new Rainbow vacuum on it.
LOL I used to have an old rainbow vac like 20 years ago..and it was 15-20 years old then lol.
Would it be practical to build a portable metal box for your air compressor to cover it incase it were to explode so shards don't go flying everywhere and hurt you or someone.
great job Brad now that vacuum cleaner totally sucks! 😁
I think somebody ran a Bissell vacuum with no filter. That’s how the dirt went into the motor impeller
I just saw your video….my vacuum (2191 model) is making a super high sound that I can not figure out. Already cleaned the filters and changed the belt and roller. Can you recommend anything?? Thanks
Tear it apart like I did down to the motor level. See if the motor impeller is clogged. Probably something stuck in there, or just covered in too much debris. Might also need to be oiled.
How do I replace belt/
I keep straight and curved forceps in various sizes, to clean out things like that 45:00
VacLab has the same vacuum cleaner
Cat litter dust did my motor in😢 same make and model
I prefer bag type vacuuums, change the bag, done. The only design flaw was the owners.
I agree. I'll use a very old Kirby or Hoover instead of a Bissell Powerforce Helix
Dire Straits - Hoover Mover! 👍
how long should you wait for filters to dry before using?
Put them in front of a running fan for 12 hours or wait a full day.
Brad I hope you are wearing a mask! You are even choking me just watching you knocking all that filthy crap out of those filters!
Halfway through your video, watching you wash the filters.
FYI if you don't want to use so much water, just stick them in a bucket of nice soapy water, squeeze the Living daylights out of them, soap 'em up again, rinse.' em, then Place clean filter in front of your a/c - heat vent in your house to dry them quickly
Now. Gonna try to tackle the problem of no suction in the old filthy vacuum I found. After a thorough washing of the top part and the collection bin, separator and filter, it still has no suction. I even washed out the hose, but to no avail.
So, back to your video to see what I can learn
Edit... well, it looks like it's more than I can bite off into. I probably have inherited the same clogged motor parts that you found when you took it apart, and I'm just not capable of doing things like that. Unfortunately when I take things apart, I could never get them back together LOL so, I still have no section then we'll probably just throw away my machine. It only cost about $56 and it would not be worth it for me to get it serviced by a professional. Thank your figure video I wish I could have learned more, and had the confidence to do what you showed. So thank you anyway
We take our vacuum apart all the time. With 2 dogs we have to clean it.
I've tried to fix a few of these up, but I was never successful, no way to even save the motor out of these,it's all part of the frame right.
🤣👍🇺🇲
isnt just the amperage the only real diff in suck machines?.....
The sparks from where the brushes are they shouldn’t be their while running been there all the time means it needs new brushes as it’s worn down to the spring and the spring is rubbing the armature you should only see sparks from the brushes on start up
Creating suction is a dirty job.
Commercial every 5 minutes. I hope YT is paying you the big bucks.
This might be one of those times you want to use a mask.
They have legitimate uses. This would be one of those.
HEPA Cakes 🤢
I have the power force Helix by Bissell and I have two of them sitting right here in front of me and they're both pieces of garbage. My brushes will not turn the ends are supposed to spin around and they're not spinning around I'm going to have to throw both of them in the garbage and the other one is less than a year old it's a piece of crap I will never buy this vacuum again!!
I wish you could get to the point as much as you like to talk about other people because this video is way longer than it had to be. Just do it.
Eww Brad. I really like your videos, but this one is nauseating. I'll still finish it though.
Damn so you judge someone’s by their vacuum? Mine is just as dirty as the blue one which is what I have but I have chinchillas who use dust to bathe so it gets dusty. I’m not where near dirty.
If I looked at your vacuum I'd be able to tell you owned a small pet like a chinchilla.