Whitewall covers were on eBay, just search the Internet for 'portawall' or 'atlas' whitewall covers and there's some company's that sell different sizes as a set so you can do front and back wheels. Really easy to fit, search CZcams if your stuck and there's some tutorials and hints in places that sell them!! Hope this helps.
+Paul Goodey didn't change the jets, it really made a very minimal difference in the performance, I did read somewhere that one head is jetted smaller than the other but when I checked mine they were both the same so I left the carbs all standard.
+Paul Goodey I know the exhaust pipes are different sizes just where they come out of the head, the one nearest the back of the bike was smaller, most probably needs a bit more of a restriction, the only problems I had with mine idling was when I tried to start it with no air filter fitted, it wouldn't even tick over. Glad you like it.
Espen Sandum I went 2 sizes up on width of the tyre, that's the biggest you can go on the standard rim, can't remember the exact size tho, rear mudguard off of eBay.
Not Real just LED ones, rear ones from an American company called oznium.com front are just strip LED's off of eBay, both come with sticky pads on the back so they can be stuck pretty much any where.
peter alafe all off of eBay,,, pretty sure you can use the original front one and just cut it down,, mine was snapped so bought a replacement plastic one and shortened the metal frame that’s in side it so it sits closer to the wheel.
Yes removed the original and welded two tags to the inside of the frame to take the springs, seat bracket then bolted on under the same bolt that holds the tank on.
+Matt Blackk Wow thanks for quick reply! A real beauty you have made thats for sure! Something else I should know about the Shadow? I have a 125cc already, just want to build a bobber as a prosject
+xTrAx I used the shadow as it looks a lot bigger than a 125 and has a v twin engine so it fills up the engine bay nicely, you could cut the back box off and have 2 Seperate pipes but it would be very loud, up to you tho.
Sarders front one is the original cut down, I cut the metal bracket down that goes inside to get it closer to the tyre, rear is a plastic one off of eBay, I welded a bracket to the swinging arm to mount it so it's all ways in the same position to the tyre.
Petter Lerli eBay,, search for atlas or portawall I think they were called,, or search on you tube and there’s some tutorials on how to fit them and where to buy them.
Telman Ride it's the original exhaust, just cut 6" out the middle and welded the back bit back on but at a different angle then rubbed it down and painted in high temp paint and wrapped the front pipes.
Glad too see that! Was thinking of doing the same but was affraid of loudness, this sounds perfect considering the engine size. Did you fill the end tip with insulation and a perforated tube?
That’s a stunning machine! Well done 👍🏻
What a beautiful bike.
Damn indicators ! they are nice !
😍😍👌 que perfeição, apaixonei velho
jhon santos thanks very much. 👍🏼
Looks awesome 👏
Hi, nice bike, congratulations ! Please, where do you find the front and rear fender ?
Whitewall covers were on eBay, just search the Internet for 'portawall' or 'atlas' whitewall covers and there's some company's that sell different sizes as a set so you can do front and back wheels. Really easy to fit, search CZcams if your stuck and there's some tutorials and hints in places that sell them!! Hope this helps.
Lucky new owner..:)
Yes it's still for sale, the price is or nearest offer. It's still on eBay. Just search for Honda shadow 125.
*I would have went with an "8 Ball" on that gas tank! ...it is a piece of ART!
Cain tuckee64 yea but loads of people got that already, the whole point of custom is to do what ‘you’ want. 👍🏼.
How you get those white walls covers like that plz
Bonjour! très belle réalisation. J'adore vos cligno arrière pouvez vous me dire ou les avez vous trouver ??
Sais un anglophone il ne te répondras
pas
Nice.
What is the top speed on it?
Muy bonita
wtf. This bike is nearly perfect. What kind of risers are build on your bike?
Do you do builds to order?
Where did you bought all the parts for it.
Hi. the fenders where you bought them
Are you going to do another
0:20 to 0:24 is that jeremy Kyle's reflection??
Bikes now sold. 😢
what is the dimensions of front tires
Yes it's in Bristol UK. Also on eBay for next 28 days.
+Paul Goodey didn't change the jets, it really made a very minimal difference in the performance, I did read somewhere that one head is jetted smaller than the other but when I checked mine they were both the same so I left the carbs all standard.
+Paul Goodey I know the exhaust pipes are different sizes just where they come out of the head, the one nearest the back of the bike was smaller, most probably needs a bit more of a restriction, the only problems I had with mine idling was when I tried to start it with no air filter fitted, it wouldn't even tick over. Glad you like it.
would it be possible to find a weld on hard tail kit for these bikes ?
Vidar Mathisen it might be? I have never seen one personally, you could just take off the shocks and weld in tube?
no esta en venta?
Hi! Did you run original rear tyre? And that rear fender, is it about 5" wide?
Espen Sandum I went 2 sizes up on width of the tyre, that's the biggest you can go on the standard rim, can't remember the exact size tho, rear mudguard off of eBay.
150/90 15. Is the tyre size, I used a whitewall maxxis, hope this helps.
Thank you, it helps. I will try to find that rear fender you used, i like the look of it. Great bike by the way! 🙂
I know you said the bike is sold but what indicators are they?
Not Real just LED ones, rear ones from an American company called oznium.com front are just strip LED's off of eBay, both come with sticky pads on the back so they can be stuck pretty much any where.
What is that handlebar holders called? those where the handlebar is attached?
Handle bar risers are 4" high, from eBay, company called M and P in Wales. They take 7/8 handle bars. Drag bars are from the same company.
Matt, what was the lenght of your shock absorber?
Pretty sure they were the original ones. Can’t remember swapping them out.
Pls pls buddy where did you purchase both fenders from I am in need of a set like that.
peter alafe all off of eBay,,, pretty sure you can use the original front one and just cut it down,, mine was snapped so bought a replacement plastic one and shortened the metal frame that’s in side it so it sits closer to the wheel.
Matt Blackk you are the best bud. Really appreciate your reply. Thank you
How did you do it with the seat? Did you just remove the original one and then what? :)
Yes removed the original and welded two tags to the inside of the frame to take the springs, seat bracket then bolted on under the same bolt that holds the tank on.
+Matt Blackk Wow thanks for quick reply! A real beauty you have made thats for sure! Something else I should know about the Shadow? I have a 125cc already, just want to build a bobber as a prosject
By the way. Could you make the exhaust split by taking of the end? If you get me
+xTrAx I used the shadow as it looks a lot bigger than a 125 and has a v twin engine so it fills up the engine bay nicely, you could cut the back box off and have 2 Seperate pipes but it would be very loud, up to you tho.
+Matt Blackk Ok. Thank you man :)
Hi do You think Can i put 160 /90 rear tire on this Motorbike ? Is it fit there?
I don’t think so,, I think you can only go up 2 sizes from original, my tyre was a 150/90
It's still for sale
How u did your fenders? Did u gut originals?
Sarders front one is the original cut down, I cut the metal bracket down that goes inside to get it closer to the tyre, rear is a plastic one off of eBay, I welded a bracket to the swinging arm to mount it so it's all ways in the same position to the tyre.
Thank you for answer, have a nice chrismas buddy :)
Where did you buy the whitewalls?
Petter Lerli eBay,, search for atlas or portawall I think they were called,, or search on you tube and there’s some tutorials on how to fit them and where to buy them.
How much $
Hi . what measures do the tires have?
christiam reyes rear is a 150/90 15 maxis whitewall and front is standard with the whitewall cover fitted.
Hi! Good job👌🏻✌️
hello, no problem to install a 150/90 without modification?
good on the road, I will put a 150/90 shinko777WW (white wall)
The bike sold for £2000.
just bought one, im thinking i should do what you did.
In norway it would go for 4000 pounds. Maybe more.
Can you build another ?
In belgium this goes for up to 3000€
where did you buy exhaust ?
Telman Ride it's the original exhaust, just cut 6" out the middle and welded the back bit back on but at a different angle then rubbed it down and painted in high temp paint and wrapped the front pipes.
Matt Blackk oh i see thx for the answer
Glad too see that! Was thinking of doing the same but was affraid of loudness, this sounds perfect considering the engine size.
Did you fill the end tip with insulation and a perforated tube?
What exhaust ?
Standard one, but I cut it down , turned the end slash piece and then welded it together, also removed the back baffle.
I give you 2500 € on the chopper
yellow light destroy entire bike
It was just a yellow film you stick on and you’ll be happy to know I took it off after a couple of weeks.