MS03b. [Siemens Motion Control] TIA Portal Technology Object (TO) Configuration [4/10]

#TO #TIAPortal #MotionControl
Next: MS03c • MS03c. [Siemens Motion...
Playlist: • Motion Control
MS01. Video Series Open Speech
• MS01. [Siemens Motion ...
MS02. 9 Common Questions About Siemens Motion Control
• MS02. [Siemens Motion ...
MS03a. Single Axis Control - Project Introduction
• MS03a. [Siemens Motion...
MS03b. TIA Portal Technology Object (TO) Configuration
• MS03b. [Siemens Motion...
MS03c. Reset, Power, Home, and MoveJog Instructions
• MS03c. [Siemens Motion...
MS03d. Move Absolute, Relative, Velocity, Stop, and Halt Instructions
• MS03d. [Siemens Motion...
MS03e. Download Axis and Program into PLCSIM, OB91 Buffer Overflow Solved
• COM18. ModbusTCP Clien...
MS03f. Online Axis Test via Axis Control Panel
• MS03f. [Siemens Motion...
MS03g. Rotary and Linear Motion Control Online Test
• MS03g. [Siemens Motion...

[@selimalan8145]

Very useful channel. Thank you for being such a channel
Greetings from Turkey

[@electricalautomation]

Thanks Buddy, Welcome!

[@hamzajmili92]

Thank you for this effort

[@electricalautomation]

Thanks! Welcome to my channel!

[@maza6357]

Thank you for great videos

[@electricalautomation]

My pleasure! Thanks! I am working on the encoder/high pulses counter of S71200. Those videos are coming soon!

[@AnimSparkStudios]

Great effort

[@2tan90]

thank you

[@electricalautomation]

Welcome! Enjoy!

[@richardbanda2817]

Great explanation and that you. Would you perhaps have a video of setting up two synchronous axes?. If so, may you kindly direct me to that please.

[@electricalautomation]

Hope this video would be helpful czcams.com/video/hie46Yd37uI/video.html

[@TheGreen18]

Great Videos
Is it possible to Axis that is not from Siemens with the TO?
For example Beckhoff?

[@electricalautomation]

99% the Motion control and the servo drive will be the same brand. The key reason is the communication fieldbus protocol as well as the telegram. If you do have to cross the brand, most common way is to use analog output to control the drive speed and read the encoder use the encoder module.

[@marcshiftsolve2947]

Is it possible to use s7-1200 cpu instead of s7-1500 cpu's? and as well as to use stepper motor rather than servo motor?

[@electricalautomation]

You can view the video, it is using the DC motor, but the idea is the similar MS04a. Setup Positioning Axis via Analog Output, DC Motor, and Encoder
czcams.com/video/Od4cqjMst4Q/video.html
MS04b. Program DC Motor Positioning Control via S7-1200 and TIA Portal
czcams.com/video/WNVbgi67HfQ/video.html

[@elnursucayev6625]

Thank you. very useful lessons. Please show how you can instal all tia portal version on one PC

[@electricalautomation]

They can be installed together. You'd better install from the lower version V12 to V17 higher version one by one. It is not recommended to install multiple versions of WinCC Professional in one system. Regular Step7 and WinCC advanced should be no issue.

[@elnursucayev6625]

@@electricalautomation Thank you very much

[@michalkall9206]

Hello, I cant see in my TIA portal option for Virtual Axis, u know where can be problem?

[@electricalautomation]

Are you using S7-1500 PLC? Which revision of TIA Portal are you using? I assume you are using S7-1200 PLC or old revision of TIA, they don't support virtual axis.

[@EngOmar-kz9qv]

Thank you very much for your effort .
in simotion scout i was using _LineModule_Control function block to enable 36KW SLM infeed but now i am using TIA PORTAL V13 and i don't found this function block .
Please how can i find and using this function block ? .
Regards

[@electricalautomation]

Simotion is different system comparing with T-CPU or S7-1500T. In TIA Portal, power up a Axis need to use "MC_Power"

[@EngOmar-kz9qv]

@@electricalautomation
if i want to enable 36KW smart line infeed, also i have to use
MC_Power ?

[@electricalautomation]

@@EngOmar-kz9qv No, sorry, MC_Power is used to power up axis. For the Smart Line Infeed enable, maybe search "xx Infeed xx" FB, the "Linemodule" may be changed to "infeed"