Cycloidal Curves_Cycloid_ Advanced_Problem 4
Vložit
- čas přidán 12. 09. 2024
- Download the Manas Patnaik app now: cwcll.on-app.i... A wheel of 50 mm diameter rolls towards the right on a horizontal floor for half revolution and then on a vertical wall in the upward direction for the remaining half revolution without slipping. Draw the locus of the point P on the circumference of the wheel. Take the initial point of contact with the floor. Name the curve.
My Affiliate Links:
My Samson Go Mic: amzn.to/2xgE0qR
My Wacom Writing Tab: amzn.to/2xh8FEv
Books I refer: amzn.to/2xe550a
amzn.to/2xgbJ3E
amzn.to/2jJOMmf
3 years have passed and this is helping us students in the quarantine period...thank a lot prof. patnaik
Knowledge lives forever...
Thank you so much sir!!!
Everything regarding EG I learnt by watching your videos and they were so helpful.
May lord shiva's blessings be with you forever!❤🙏
Such a great channel, for your info, this channel is now recommended in IIT Ropar by seniors as well as students for engineering drawing. Nice content. Appreciate it.
How long the horizontal lines should be taken???? You never explain that
Your wish
You can do upto the end of the drawing sheet😂
hii bro..grt work! able to understand ed in better way sitting at home
Thanks kunj for appreciating my work...
Do encourage your friends also to subscribe and learn from this channel.....
All the best in life....
Manas Patnaik sure sir👍
Kunj Chandarana
u were correct chandarana.
y such a good content has no views?
@@ManasPatnaikofficial already our lecturers are sharing your videos in classes sir
At 7:06 c5 as the centre what will be radius?
2.5mm
I don't get why this channel has only 9k subs while content being this good
Thanks Dugaprasad for appreciating my work...
Do encourage your friends also to subscribe and learn from this channel.....
All the best in life....
Ur teaching was awesome sir and ur clarity in voice tq sir
Hey Tejaswi.......Thanks for appreciating my work....
All the best in life
I have also started making lectures on engineering mechanics
Do check it out on my channel page...
Do share and recommend this channel to your friends and classmates so that they can also benefit...
Cheers....
Will it be the same if first half is in the vertical plane and second in the horizontal plane?
Sir how to convert 3dto 2d easily
sir i am getting the wrong p7 point and therefore a different curve appears from point P6 TO P8.Can you help me with that
Tysm my doubts has been cleared😊👍
Tq sir for ur efferts for doing such understandable videos...
My seniors recomended me to watch ur videos...i tooo...do the same work to do watch your videos to my friends & up coming juniors....
Sir your videos so conceptual I learn ed from your videos
Hlo sir awesome class it was so useful to me to understand the concept TQqqqQ so much such a wonderful video keep on teaching
Ur the best teacher i have never seen
Excellent sir:; you have an excellent talent of explaining it
Tanq sir
Thanks Raj....
Great work!
Thanks for uploading this video.
what is the radius for the arcs from c6 and c7 ?
A circle of 50 mm diameter rolls on a horizontal line for a half revolution andthen on a vertical line for another half revolution. Draw the curve traced outby a point P on the circumference of the circle
Q- cycloid ,diameter-50 ,rolling,starting point P farthest from ground ?
Hii sir thanks sirfor clarifing doubts
A circle of diameter 50 mm rolls without slipping along a straight horizontal line for half revolution; it slips for 25 mm and stops. Draw locus of point on the circle which is initially in contact with the directing line. Name the curve.
great work ur genius manas patnaik. Really y such a good content has less views.of all the drawing classes I watch in u tube this is the most suggestable .
Srujay..........Thanks for appreciating my work....
All the best in life
And do recommend this channel to your friends and classmates so that they can also benefit...
Cheers....
Manas Patnaik
ty for such a good content videos I will suggest my friends compulsory sir
Damn!! You're so Good 👌
Have fun Devansh....
All the best man
Yadi aap nii hote to 8th sem tk clear nii hota ed pass ho gyi mai ed me thankuu thankuuu sooo much
When the circle is in vertical motion, what is the radius of the arc with C5 as centre and so on? Is it equal to the radius of the circle or the distance between C3 and C4?
It is equal to the radius of circle i.e small "r"
Manas Patnaik Thanks a lot. Appreciate it :)
A point is moving along the curved surface of a cylinder with a uniform speed and parallel to the axis. The cylinder is rotating about its ads with a uniform angular velocity in anticlockwise direction. From bottom of the cylinder, point P is covering a distance of 129 in two rotation of cylinder. Plot the locus of P for two complete rotation of cylinder. Take cylinder diameter equal as 60mm. name plotted curve ? Sir can you please make video on this
please show how can we make a cycloid when a point is on a circumference which is about any distance from base ... how to make such cycloid .. please show the solution asap ....
sure sayyad....very soon i will be doing a tutorial on that
Thank you very much
In this video you have taken the starting point at the bottom of circle.wt about the cycloid when the starting point is at the top of the circle?
Sir how did the point P6 touched the 6 center line ? Because the radius b2in c3 and c4 is less than the actual radius.
Its equal to going to CLG sir superb use full thank u sir
sir in question it was given to name the curve??? sir and also can a circle rolls on vertical wall
Thank you sir your videos are very helpful
❤❤❤ my tutorial question 😃
what to do when a circle rolls without slipping along a straight line for half revolution and it slips certain distance and stops and it is asked that to draw a locus of a point on the circle which is initially contact with the directing line plz anwer.
Please some one tell that when we marks arcs from p5, p6,p7 whats is length of that arc???
+TEJAS THAKRE
It remains same i.e the radius of rolling circle itself......
Manas Patnaik oh it means radii of circle.....?
It's really amazing sir🤩🤩..
damn, i wish u were teaching where i study.understood each and everytghing
Sir y can't v divide the circle into 12 equal parts?
From c5 c6 c7 how do we decide that arcs are clockwise or anti clockwise in direction..
Can we draw 1.5 revulation
I want to know what happens when it rolls down
Sir is there anyway to send question to you and please make one video on Spiral and in hypocloid case when d= D/2. Thanks for so many good videos Sir.
Thanks Udit.....i am planning to make a video on spiral asap.
Thank you sir
sir what about the conditions of epicyloids and hypocyloids
it helped, thank you sir 🎈
Thanks for the appreciation Sid...
All the best and do spread a word about this channel with your friends and classmates so that all can benefit.
Due to online class i don't know how to use mini drafter so pls help me sir to understand it in proper way 🥺
In question they asked name the curve.What is the name of curve
Thank u sir for your efforts
Sir How to cut curve.
, amazing to learn e d sir 😘😘thank you u most
If initial contact at top then how to draw cycloid
Thanks 🙏 sir
Well explained. Thanks
Thanks for appreciating my work Ande....
There are whole lot of projects i am working on right now....
So consider subscribing and do let your friends know about this channel so that they can also benefit...All the best.....
Sir it is useful.would you give your contact?
Sir I needed some reference for half horizontal and half inclined 60°to the surface
Pratham....well thats something which can only be demonstrated...
It cant be explained in words.........
but sir,we how we know that in which direction we have to make arcs for c1,c2......
Well we just assumed that the wheel would travel upwards after first half revolution.
You can assume that the wheel would travel downwards after first half revolution and carry out the whole process again. The curve that you will get will be slightly different.
Thank you so much sir
thank you sir...
Samyukya.............Thanks for appreciating my work....
All the best in life
And do recommend this channel to your friends and classmates so that they can also benefit...
Cheers....
why don't we divide a circle into 12 equal parts
12 parts take more time thats y
Draw a Problem of isometric
Thanks a lot sir
awesome vid :)
Thanks Sameer for the appreciation
All the best...
And do let your friends know about this channel so that you all can benefit...
U ll succeed one day
+Ruman Mulla
Thanks for your encouraging words Ruman....
All the best in life....
how cycloid look like when point is at top of circle
All half information ur giving it's not very clear
How to draw revolution in downward direction wall
Try to work it out yourself Archit...
I am sure u can....
@@ManasPatnaikofficial hiii sir mene try kiya par draw nahi ho pa raha he ,,..
Nice sirrrrr
different problems on cycloid itself
Do it practically sir
I we divide circle in 8 parts then we also have to divide tangent line into 8 parts or not?
Tq so much
Thanks a lot AAGVPR for appreciating the content...
Do check out Engineering Mechanics also on my channel page...
All the best...Have a great time and CHEERS...
Thankuuuu soo much sir
perfect 😍😊😊
Shegaon chi kachori chai Ani mag pahe chamatkar chonga
ty bro.....
For downward
U can try it......
Subjectwise Playlist:
1. Engineering Drawing/Graphics (English): czcams.com/video/WG6H2pISUzQ/video.html
2. Engineering Drawing/Graphics (Hindi): czcams.com/video/SB83cUaAiCM/video.html
3. Engineering Mechanics / Applied Mechanics: czcams.com/video/Z4WN2Z9okfs/video.html
4. Mechanics of Solids / Strength of Materials / Mechanics of Materials: czcams.com/video/Co4YlavCpeQ/video.html
5. Theory of Machines: czcams.com/video/Co4YlavCpeQ/video.html
6. Machine Drawing: czcams.com/video/iFCnFUR9Gdc/video.html
7. Engineering Drawing for Engineering Services Prelims: czcams.com/play/PLIhUrsYr8yHwFTNav_k3EEIvztQEQHilU.html
8. Physics for Class 11: czcams.com/video/0fejUC79LZY/video.html
9. Manas Speaks Series: czcams.com/play/PLIhUrsYr8yHz9g5V7Lw_BA5UXbAbgVyf0.html
10. Channel 2 Link:
czcams.com/channels/_aqx41HWeOebfL6FqBYU6Q.html
Tq sir
Wangachi bhagi and gaap gaap Shira khai beta Ani fakala han video madhe to
Thank you sir
Hi Pratyush.........
I am sure these videos are helping you learn the concepts...
All the best and do let your friends know about this channel so that they can also benefit.....