Absolutely brilliant. Thank you. Saved me a load of time trying to figure out how to remove the switch. I just hope that the new switch has sorted my problem
Thanks! This was the problem with a family member's car, and your video helped. Didn't buy a new swtich however, as the issue is the wear in the plastic where it rotates. I put some electrical tape in the hole to make it wrap around the metal thingy that sits in there, to make a more tight fit. And it worked very good!
Thanks a lot for showing us how to change the ignition switch. I changed it today in my Micra K12 (my steering wheel is on the left). Was a bit difficult but I finally got it!!
Good video. As a further note to others...... I discovered a way to get to the two screws on the switch more easily. To the right of the ignition, on the Sport+ model, there is a piece of trim with a couple of switches and a little pocket. This comes out easily, thus enabling you to get a screwdriver in the right place to remove ignition switch.
I knew the ignition switch was on its way out and after watching this video i bought a replacement switch (and angled needle nose pliers) ready for when it did finally go (ebay £12.99 switch. Amazon £7 pound pliers). My top screw was hampered by the plate that releases and clamps when you adjust the steering wheel. Anyway as soon as both screws had a couple of turns on them I was able to get a finger from each hand in and spin the screws out. If you remove the switch panel to the right where the wing mirror switch is you can get round the back and with the right size scew driver get to that top screw. I only realised this when putting the screws back in but managed to fasten the top screw with an old small screwdriver that had a broken handle not ideal but easier than putting screw back in with pliers. Took me 1 hour 30. Good luck anyone trying this, fiddly but doable.
As the back screw is not accessible, I pulled the plug from the back, and exposed the red and white wires. Splicing a suitable push switch across these two wires means the switch will operate the starter, but only when ignition is turned on. The switch is mounted on the dashboard beside the headlamp height adjuster. Works every time - problem solved!
This worked for our 55 plate micra 👍👍👍 great video! Just had to buy the long angled pliers but I’ve got them in my tool bag for future… too tip to rough up the screw with mole grips before reassembly.
Great video this helped me replace mine and used the long nose pliers etc. Top screw very fiddly and it took about 2 hours to do. Thanks for the Video.
great video thank you! I'm going to have a go myself. I have been told that nissan know about the issue as it's a common problem but never did a recall. I hope my father fingers will work!
Just done the job with a very long cross head screw driver up from the footwell. It took longer to take the surround off and replace than to change the switch
Think this is the best approach. I used 6" long screwdriver and I reckon an 8" screwdriver with a narrow handle would have been easier. The handle was hitting the steering column.
Great video, just finished the job took me about 30 min, cost of "ignition cube" 22€ with delivery from eBay. It is easier than it looks, and car now working perfect. And if your hands are slim enough, you can manage it only with screwdriver, as I did. Thanks.
Thank you, very helpful information, my old switch was also burnt , so i cleaned it up and eventually got it back together and working, how well im not sure but could get someone out of trouble latter. cheers.
Thanks for this video! I just spent 2 hours sorting mine, it's done! ( And I'm a not particularly practical woman!) It would have been quicker if I didn't lose one of those tiny screws and have to hunt high and low in local shops to find a replacement! Don't drop it! They aren't very common! I didn't have long nose pliers, so took off a bit that also covered fuses on right which just gave me space to get a tiny screwdriver in place Grazed and cut fingers and knuckles though..
Wow :) we are glad we have woman watching and using our videos :) 2 hours is a right time to do that, keep working on your car :) and thank you for comment.
Just did this took me about 2,5 hours. On my car the steering wheel position lock was in the way of the back screw. You can remove the steering wheel position switch nut and clamps from the right side(not lever side) this gives a bit more room to remove the back screw. Made it much easier for me :)
Just did this. One point that might make someone's life easier - just remove the starter key barrel altogether. It is held to the steering column with one bracket and 2 flat head screws - undo those while supporting it (it is heavy). After you detach it pull it aside just enough so you can access the screws on the ignition switch. Replace the switch and put the barrel back pone - should be done in about 10 minutes tops.
As an update to my comment below, I still had some stiffness and clunkiness. I had bought a second hand injection switch from eBay and suspected that the one I'd bought and fitted also had a problem (especially as it's such a common one with Micras(. So I went for it and ordered a new nissan one from nissan parts eBay shop ( £50), I fitted it in 25 mins this time and it's now perfect! So, if anyone still has problems or if trying for first time, it's prob worth getting a new replacement rather than secondhand!
witam dzięki za film pomoglo,chcialem wymienic,pompe paliwa ,albo lancuch rozrzadu,czujnik walu,a rozwzanie bylo prostrze/hello, thanks for the movie helped, I wanted to replace, fuel pump, or timing chain, sensor shaft, and the solution was simpler.
Have same issue with a micra I just bout n Galway .. she blue too lol.. bought a starter for it today but it starts sometimes so now I’m thinking it’s the ignition 🤨
I fixed this problem installing a button,i insert the key for turn on light and each other electronic device,but for start the engine i press the button,it's more easy
I just bought a Nissan Micra and the ignition is sticking.(Just like what happens in this video). I have been told I need the ignition switch, the back part. I assume this part you are fitting is the same one? If so, I have seen on ebay for £57 euros. Is that too expensive? How much do Nissan charge? Thank you
I dont have any a screw on my car. I got ignition problem and i tried to take out but i dis not got any the screw. Please could you tell me what kind of screw is it? I would like to order via online please help me
With my k12 the key Goes around juist richt but iT stil wont start, the previous owner had iT “fixed” by installing a start switch. Now u turn the key to on position and pres start button and iT starts. Not happy with this, i wamt iT to be original. Luckily i have that same part as what u uses. Now i juist hope the wiring is stil ok
Can you please help mine cranks but will not fire up? Fuel goes ok spark ok injectors ok what else can it be, car was driving fine for 150 miles switched the car of never started again ?
Hi, so... if you have a spark , fuel delivery , time check timing. Make some video with during try to starting the engine. And give me some car details .
FixYOURride13 my explanation was wrong but i meant glow plugs ok fuel feeding ok injectors ok, it only starts with deodorant or easy start as soon as you stop spraying goes of ????? What do you thing compression maybe?
@@ALKUKES ok so probably problem is in fuel supply system, tray turning the engine with open injectors fuel pipe supply and check fuel pressure. What car it is?
Sorry that's video was made 2y ago I don't remember the parts number but if you give me car details (vin number, engine kode, year) I try found parts for you.
simple soloutin for this problem is get a universal start stop button which costs you around £5 and 0.70p for 2 meter wire and take it to any garage they ll charge you around £30 to put the button in thats it your problem solved .then all you do is just turn the car on and press start button and car will start.am telling you this because thats what i did when i had same issue with my ignition barrell and every one was saying get ignition barrell which i couldnot find because scrap yards dont always have them and you have to wait weeks.
Hello I forgot about this video until a similar one came up on my video list and then yours, I managed to get the screw off in the end after 5 days of trying, thanks. My fiends car is still going with the new ignition switch.
Czesc, mja zona ma ten sam problem w swoim nissanie micra, mozesz mi powiedziec jak dokladnie nazywa sie ta czesc ktora wymieniales z tylu stacyjki?. Pozdrawiam i dzieki za film
Good morning. What is the proper name of the part on eBay? I'm having similar issues with my car. One minute it starts the next minute it doesn't. Thanks for the great video!! Cheers.
Hi i have a problem the first acc that turns the radio on is not working And everytime it needs the code to work cz radio wont work only if i start the car
Clear step by step instructions. Made a potentially difficult and costly repair easy. My ignition now starts first time every time. Thanks very much.
Absolutely brilliant. Thank you. Saved me a load of time trying to figure out how to remove the switch. I just hope that the new switch has sorted my problem
Thanks! This was the problem with a family member's car, and your video helped.
Didn't buy a new swtich however, as the issue is the wear in the plastic where it rotates. I put some electrical tape in the hole to make it wrap around the metal thingy that sits in there, to make a more tight fit. And it worked very good!
Thanks a lot for showing us how to change the ignition switch. I changed it today in my Micra K12 (my steering wheel is on the left). Was a bit difficult but I finally got it!!
Good video. As a further note to others...... I discovered a way to get to the two screws on the switch more easily. To the right of the ignition, on the Sport+ model, there is a piece of trim with a couple of switches and a little pocket. This comes out easily, thus enabling you to get a screwdriver in the right place to remove ignition switch.
Thanks for the tip buddy, that was a real time saver!
does the car in the video has that same trim you talked about?
I knew the ignition switch was on its way out and after watching this video i bought a replacement switch (and angled needle nose pliers) ready for when it did finally go (ebay £12.99 switch. Amazon £7 pound pliers). My top screw was hampered by the plate that releases and clamps when you adjust the steering wheel. Anyway as soon as both screws had a couple of turns on them I was able to get a finger from each hand in and spin the screws out. If you remove the switch panel to the right where the wing mirror switch is you can get round the back and with the right size scew driver get to that top screw. I only realised this when putting the screws back in but managed to fasten the top screw with an old small screwdriver that had a broken handle not ideal but easier than putting screw back in with pliers. Took me 1 hour 30. Good luck anyone trying this, fiddly but doable.
As the back screw is not accessible, I pulled the plug from the back, and exposed the red and white wires. Splicing a suitable push switch across these two wires means the switch will operate the starter, but only when ignition is turned on. The switch is mounted on the dashboard beside the headlamp height adjuster. Works every time - problem solved!
This worked for our 55 plate micra 👍👍👍 great video! Just had to buy the long angled pliers but I’ve got them in my tool bag for future… too tip to rough up the screw with mole grips before reassembly.
Great video this helped me replace mine and used the long nose pliers etc. Top screw very fiddly and it took about 2 hours to do. Thanks for the Video.
great video thank you! I'm going to have a go myself. I have been told that nissan know about the issue as it's a common problem but never did a recall. I hope my father fingers will work!
Just done the job with a very long cross head screw driver up from the footwell.
It took longer to take the surround off and replace than to change the switch
Think this is the best approach. I used 6" long screwdriver and I reckon an 8" screwdriver with a narrow handle would have been easier. The handle was hitting the steering column.
Great video, just finished the job took me about 30 min, cost of "ignition cube" 22€ with delivery from eBay. It is easier than it looks,
and car now working perfect.
And if your hands are slim enough, you can manage it only with screwdriver, as I did.
Thanks.
Hi , it's my pleasure, but if you wish Donated our channel pls jump to channel information, many thanks for any one euro ;););)
Thank you, very helpful information, my old switch was also burnt , so i cleaned it up and eventually got it back together and working, how well im not sure but could get someone out of trouble latter. cheers.
Excellent!! Far better than the button replacement!! Well done!!
Thanks for this video! I just spent 2 hours sorting mine, it's done! ( And I'm a not particularly practical woman!)
It would have been quicker if I didn't lose one of those tiny screws and have to hunt high and low in local shops to find a replacement! Don't drop it! They aren't very common!
I didn't have long nose pliers, so took off a bit that also covered fuses on right which just gave me space to get a tiny screwdriver in place
Grazed and cut fingers and knuckles though..
Wow :) we are glad we have woman watching and using our videos :) 2 hours is a right time to do that, keep working on your car :) and thank you for comment.
Just did this took me about 2,5 hours. On my car the steering wheel position lock was in the way of the back screw. You can remove the steering wheel position switch nut and clamps from the right side(not lever side) this gives a bit more room to remove the back screw. Made it much easier for me :)
Just did this.
One point that might make someone's life easier - just remove the starter key barrel altogether.
It is held to the steering column with one bracket and 2 flat head screws - undo those while supporting it (it is heavy).
After you detach it pull it aside just enough so you can access the screws on the ignition switch.
Replace the switch and put the barrel back pone - should be done in about 10 minutes tops.
Thanks man! I've managed to solve based on your video. Awesome.
I like your work in this video. Big up!
Today i replaced the startblok.
Used the same tools and it worked.
Thanx for the video .
Great video, thanx for your help👍
Cheers dude helped me no end ta!
Great effort thanks for your help
As an update to my comment below, I still had some stiffness and clunkiness. I had bought a second hand injection switch from eBay and suspected that the one I'd bought and fitted also had a problem (especially as it's such a common one with Micras(. So I went for it and ordered a new nissan one from nissan parts eBay shop ( £50), I fitted it in 25 mins this time and it's now perfect!
So, if anyone still has problems or if trying for first time, it's prob worth getting a new replacement rather than secondhand!
£16 delivered and new from Ebay
Thank you very much for this nice video, i wish you good continuation with more interesting video.
Great job I'm going to attempt at myself I've got the same problem thanks for posting 👍
witam dzięki za film pomoglo,chcialem wymienic,pompe paliwa ,albo lancuch rozrzadu,czujnik walu,a rozwzanie bylo prostrze/hello, thanks for the movie helped, I wanted to replace, fuel pump, or timing chain, sensor shaft, and the solution was simpler.
Cześć, fajnie że film się przydał, pozdrawiamy ;)
Great video saved a fortune thanks
Cheers mate, very useful guide👍
Nice idea to fix that problem.
Meantime a found part code. Thanks
can you share it with us?
love the video. subbed and subscribed.
Thank you :)
Great video saved me 140 euros
Great helpful vid and i replaced mine following your vid. A few months later and the new part has sldo failed. Bad design i think. In we go again😂
Sorry to hear that
@@FixYOURride13 turned out to be the starter motor this time👍
well done great video what size engine do you have and is that right 181.000 on the clock the engines must be good
Hi, thanks, forgive me, I don't remember, but 100 % petrol.
Have same issue with a micra I just bout n Galway .. she blue too lol.. bought a starter for it today but it starts sometimes so now I’m thinking it’s the ignition 🤨
I fixed this problem installing a button,i insert the key for turn on light and each other electronic device,but for start the engine i press the button,it's more easy
what colour cables did you use wire up the button ?
Спасибо!
I just bought a Nissan Micra and the ignition is sticking.(Just like what happens in this video). I have been told I need the ignition switch, the back part. I assume this part you are fitting is the same one? If so, I have seen on ebay for £57 euros. Is that too expensive? How much do Nissan charge? Thank you
I dont have any a screw on my car. I got ignition problem and i tried to take out but i dis not got any the screw. Please could you tell me what kind of screw is it? I would like to order via online please help me
Vielen Dank
With my k12 the key Goes around juist richt but iT stil wont start, the previous owner had iT “fixed” by installing a start switch. Now u turn the key to on position and pres start button and iT starts. Not happy with this, i wamt iT to be original. Luckily i have that same part as what u uses. Now i juist hope the wiring is stil ok
Can you please help mine cranks but will not fire up? Fuel goes ok spark ok injectors ok what else can it be, car was driving fine for 150 miles switched the car of never started again ?
Hi, so... if you have a spark , fuel delivery , time check timing. Make some video with during try to starting the engine. And give me some car details .
FixYOURride13 its 1.5 dci 2007
@@ALKUKES you tell me "spark ok" you check an found the spark in diesel engine ???
FixYOURride13 my explanation was wrong but i meant glow plugs ok fuel feeding ok injectors ok, it only starts with deodorant or easy start as soon as you stop spraying goes of ????? What do you thing compression maybe?
@@ALKUKES ok so probably problem is in fuel supply system, tray turning the engine with open injectors fuel pipe supply and check fuel pressure. What car it is?
Hi, Could you please provide me the product code for the switch that you changed?
Sorry that's video was made 2y ago I don't remember the parts number but if you give me car details (vin number, engine kode, year) I try found parts for you.
simple soloutin for this problem is get a universal start stop button which costs you around £5 and 0.70p for 2 meter wire and take it to any garage they ll charge you around £30 to put the button in thats it your problem solved .then all you do is just turn the car on and press start button and car will start.am telling you this because thats what i did when i had same issue with my ignition barrell and every one was saying get ignition barrell which i couldnot find because scrap yards dont always have them and you have to wait weeks.
Hi, someone like separate start botton, onother like original set, that all in this story 🙄
I can't get the one screw out using pliers can u give any advice please
shazad1977 ,hi, you have to removed steering column , sorry
Hello I forgot about this video until a similar one came up on my video list and then yours, I managed to get the screw off in the end after 5 days of trying, thanks. My fiends car is still going with the new ignition switch.
Thanks for the video can someone tell what’s the part name thank u
Hi, as in the title, - ignition switch -
Czesc, mja zona ma ten sam problem w swoim nissanie micra, mozesz mi powiedziec jak dokladnie nazywa sie ta czesc ktora wymieniales z tylu stacyjki?. Pozdrawiam i dzieki za film
Witam ta część to "Ignition switch " Pozdrawiam ;)
@@FixYOURride13 dziekuje
Good morning. What is the proper name of the part on eBay? I'm having similar issues with my car. One minute it starts the next minute it doesn't. Thanks for the great video!! Cheers.
Hi, it is the " ignition switch " :)
@@FixYOURride13 thank you. I think I'm going to install a push button switch brother. You all be safe as the world combats COVID19. Take care!
Hi i have a problem the first acc that turns the radio on is not working
And everytime it needs the code to work cz radio wont work only if i start the car
Hi, check Acc fuses in all fuse boxes in the car.
@@FixYOURride13 thx
How many kilometers does this vehicle travel with a tank of gasoline?
Hi, it is not my car, so I have no idea, sorry
Putting the screw back in looks like a night mare, anybody found a cheaty way of doing this? Im thinking a tiny cable tie may do it.
Hi,you can dropped down all steering column 🤘
I used a piece of multi-stranded copper wire wrapped once around the screw.
How i start man
Hi, you ask about ?
I have this problem but unable to do what this bloke did wish come fox mine
10:48
Good job man! it works for me no problem now, 🫡