45 degree welding
Vložit
- čas přidán 29. 09. 2023
- Holwtoweldforbeginners#welder#welding#beginnerswelder#stickweldingthinmetal#weldingsquaretujnlbe#weldingtipsandtricks#stickweldingfabrication
Label:
Weldingtipsandtricks
Weldingtechnique
Weldingmethod
Weldingticks
Weldingmachine
Weldingprojet
Weldingskill
Weldingwork
Weldingcreative
weldingtutorial
Stivkwelding
Arcwelding
Weldingforbeginners. - Jak na to + styl
I’m convinced he just make videos to piss welders off
Was thinking the same thing.
Non c'è altra spiegazione
Well it’s definitely working!! 😡🤬😅😅🤣🤣
😂😅
Нарисовал полумесяцем, показал круговыми, сварил точками
Не сварил, а насрал
Рукожоп как ещё это назвать
😂😂😂
И почему твой коммент не в топе?
Chắc hẳn bạn mới tập Hàn
Show a technique with marker and done other... Why???
You make sentence stupid… Why?
What you're seeing here is completely flawed welding job.
Previous to tacking the 2 pieces together. A grinded bevelled edge on either side needed to be done, allowing penetration for the weld. Also the pen marking showed weaving which was not done in the video. The operator was simply stop starting. This process would fail a welding xray once tested.
To get you to comment. It’s a tactic used by these “creators” to force their channels into the algorithm. They’ll do something like the marker thing or mispel an esey word just to get someone to correct them or get out ragged by it. It bumps their videos bc they’re getting more clicks . Hence more views hence a few more dollars. It’s honestly sick. Like have you heard the video “yo guys …. Loook what I even found in my dads room…… is this a gloock?” Just mind melting nonsense. Hell I have made videos that takes hours and nothing. Made a video just now of a lawn mower running and it’s got 10000 views in an hour. They are making money by making dumber and dumber content. It’s bad
@@T.M....what you’re seeing is a guy who knows what he’s doing getting you to comment on his video for views . That’s all. He knows how I’m sure. He’s doing this on purpose
He actually show 2 different techniques then used the bullshit one
You, my friend, would make an excellent politician
Вообще в цвет👍
Hahahaha so nice
😂😂😂😂
😂😂😂
😂😂😂😂😂😂😂🤝🤝🤝
You demonstrated one technique with your marker then done your typical useless spot weld trash
I know nothing about welding. Care to explain a little more to me?
The type of welds shown in this video is a really bad technique from someone that clearly doesnt know how to weld. The weld has no penetration, so it wont hold up much force.
@@samv6767yeah I could excuse the tack welding to just stick the two together long enough for him to lay down an actual good weld. But come on
@@obiwanfisher537the proper technique would be to tack it like he did, then weld it as drawn with the marker in a single continuous weld.
The rods are encased in something to protect your welding bath from oxygen, leaving slack behind. That's what he removes in the end, but by not removing it every single time, some slack may get trapped leaving you with inclusions weakening the weld.
So tack, remove slack, thinner rod, less amperage, one continuous weld, remove slack, finished.
If some of my words are not the correct terms, I am sorry, english is not my native language.
@@derewe2094 Dunno, english is my second language, too. And on top of that I am not familar with welding terms anyway, but I think I got what you mean. Basically, he dotted the thing and created weaknesses like that, but he should have welded it in one contact.
Это не сварщик, это начальный уровень практиканта
👏🏽👏🏽🤣🤣🤣
всё так легко получается.
я делаю так же, но у меня не получается ничего.
@@YamomotoSC2TV пробуй полуавтоматом тогда будет проще и легче, по ролику видно что человек не опытный катит шва практиканта видно что не давно варить начал электродами.
Párese ,déjenlo ser 😊
Практиканта не обижайте 😂
Guys, he can’t do anything else because he can’t control the heat with every car battery in the village hooked together.
Oh shit😂🤙🏽💯
More precise current control can be achieved by utilising the fine current ajustment (fencing wire series resistor) feature on your new welding machine.This in combination with the two, three or four car battery selections, will give you the 50 or so O.C. volties you'll need to lght and re-light those pesky low hydrogen sticks that you all should be using for the more serious structural jobs like, repairing broken crank and cam shafts, truck axles and gear box input shafts to name a few.
😂😂😂
Motherfuckin HAAAAAAAAAAAAAA Comment of the century
Keine Qualität!Fusch!
Маркером показал одно, электродом другое, а как начал варить так вообще по другому делать стал
Hopefully in a couple years when actually welds he can think back and be like " did i really post this on youtube ? " 🤣🤣🤣
Imagine how good it could have been if you could only run a proper bead
That would be nice to see one continuous bead for once😱
Насрал
That would require knowledge of Amp settings, electrode type/size selection, and actual practice. I'm not a pro, but I know enough to conclude there are better ways than the "Tackmaster Flash" technique...
Ток убавь и чаще точки делай. Так чешуйки ближе будут, шов будет куда лучше, качественнее и красивее.
Он людей на комментарии байтит.
Братва, зашёл прокомментировать.а тут откоментированно
А если уони взять и ток 35 а то можно и слошняком с проваром даже 🎉
А то что провара толком нету? 😂
Нормально он сварил.
If the trick was "how to do an improper weld" then you nailed it.
Молодец студент, продолжай учится, скоро получится.
Вот уж чего чего, конечно же пускай учится, авось что получится...
у меня не получается даже прихватку сделать. электрод то прилипает, то не зажигается, то прилипает только к одной стороне. а тут раз два и готово. да как так то(( мне так обидно пипец
Прилипает и не зажигает, часто из 9а плохой массы, или слабого тока@@YamomotoSC2TV
@@YamomotoSC2TVпопробуй поменять электроды, может получится лучше, я тоже не профи, самоучка, но варю примерно как на видео, понятное дело что профи заварит практически любым электродом. И кстати, а аппарат инвертор?
@@roman_mehan8853 да инвертор. валик (шов) он как будто не вваривается в метал а колбаской накладывается, как будто слишком быстро электрод плавится а железяка не успевает проплавляться. и шов получается как бы не приплюснутый а высокий, выпирающий. еще и приплавляется то к одной железяке то к другой, хотя веду его по центру (как мне кажется)
Nice porosity.
It keeps water from building up! 😎
Actually wasn't any. Still a trash weld.
@jjjordan3881 Get some glasses son.
Slag makes a good filler too lol
When a beginner welder shows a beginner welder his trash!
Agreed! I don't know what's up with this start stop BS all over CZcams, but that's not how you weld. ITS TRASH! It's not gonna hold shit.
I'm 14 and do better
I’m still in my first semester of trade school so maybe I’m missing something, but why for the love of all that is holy can you not just run a straight fucking bead.
He would burn through if he ran a straight stinger as is. But he could switch from DCEN to DCEP and use a small diameter electrode with less amps and easily run a stringer
You show one technique but then decided to stitch weld instead... if your concern is blowout turn down amperage and use a smaller diameter rod. Stitch welds are viable on something only if it isn't expected to bare a load... so ornamental or artsy shit... but if that 45 is expected to take any pressure your going to want full penetration that comes with a full run of either a C circle or J hook... hell a slow zigzag will provide more penetration then a stitch...
Still didnt see any porosity pockets or slag deposits in your end result so theres that i guess.
Also good on you for brushing your work before beginning the weld... remember that prepwork makes all the difference.
Glad you're giving pointers, I'm sure it means a lot in this world(welding)
@@Loki_Dokie I like seeing people get into the trades ether for work or just to have the skill in one's own toolbox... I just want to ensure it's done properly because dispite something looking bound with a decent "cap" weld or being ground and sanded flush to look like one piece the area has the potential to be much weaker then the parent metal... and if that piece is to be relied upon could lead to critical failure which can lead to injury...
@@Rageofthemohawk ya definitely, I'm a lifetime supporter of life-long learning. I want to learn to weld but I'm not sure if going ultra cheap on the unit would help me learn at least for now.
@@Loki_Dokie weld honestly there are people out there that have learned on say a Hobart or other sort of harbor freight sort of set up and it does have some advantages as with the equipments quirks and Brakedowns you really have to get a keen understanding of the mechanics of your system... it may only like a particular type or diameter of wire or perhaps it doesn't like a certain amperage dispite that being within the factory limits... so it is one method of starting out. Personally I've gained most of my equipment from old timers that are getting out and retiring... typically it's good equipment in relatively good condition since they made a living with it, and it is usually what was considered high tier for the era... my opinion tends to land on get relatively good equipment since it tends to give you less trouble starting out... and the old adage holds true take care of your equipment and it'll take care of you.
You also need to decide what welding you want to start out with... personally I started out on oxy acetylene in a classroom setting and it's really good means of teaching basic touch control and even feeding control and manipulation... from there moved into wire feed and eventually found my stride and preferences in stick welding... I have my bias and I feel stick is the best everyman welding with the most versatility, but one should learn the basics of as many welding operations as possible to both understand the underlying principles and techniques... lastly prep work in terms of your material is vital... making sure your cut or bevel is clean and free of debris is good practice and gives you the best chance for success...
Какой божественный шов, позову детей посмотреть
🤣🤣🤣🤣
Довольно неплохой шов как для ММА сварки, чего Вы гоните?!!
@@user-gi6zr6gj1z шедевральный, я бы сказал
Зато меньше зачищать.
Качать электродом в этом случае не надо и немного чаще ставить точки тогда будет результат лучше ровнее и плотнее
Зачем вообще такой шов с отрывом варить?
@@kamentonточками варят тонкостенные детали, чтобы не прожечь дугой дырку. Короткие импульсы позволяют лучше рассеивать тепло, не доводя температуру до прогорания.
@@user-el2xc2su4s я понимаю. Но там шов поворотный, можно с обеих сторон низким током проварить.
Та и с одной без отрыва можно, если «придрочен» с аппарату. Нижнее положение же, зачем точки?
@@user-el2xc2su4s электрод двойка, ток подобрал и погнал в быстром темпе без отрыва.
Так понимаю, на любителя)
This welding Not good
I love how theres so many welding videos where they just do a series of tacks and call in a "crazy new welding technique that nobody uses"
Always weld from the inside out less distortion
I have no interest in welding or building stuff but I subbed to follow your journey because I’m genuinely interested in watching your growth. And to keep encouraging you and watch your back.
All of this guy's examples are how NOT TO WELD. Every time you stop, and start, slag is deposited in the weld. Also the melt doesn't penetrate the steel. Hold the rod close to perpendicular to get the heat to penetrate the steel.
Every weld this guy shows would get you fired at any competent welding company. If you weld something and ten years later it breaks and kills someone, YOU ARE RESPONSIBLE.
@@carpediemarts705 thank you 🙏 you’re the first to give constructive advice to him compared to others who know how but would rather tear him down instantly with critical comments rather than offer some valuable tips to help him improve. Huge respect and gratitude to you on his behalf. We need more helpful experienced individuals like you offering support and sound advice. 👍
@@homebuddhathe thing is these guys arent trying to get better. They'll purposely weld it stong just to get negative comments cause comments help him with the algorithm. This could even be someone elses video.
Hey, keep up the great work, you'll get there someday
Лучше бы научился сам и других, разделывать кромку свариваемых заготовок. Например, как делать V-образную разделку кромок, в качестве базовой.
এরথেকে ভাল আমি পারি তবুও সৌদি রিয়াদে বসে আছি কয়েক মাস ধরে
Wont hold, you cannot manipulate a stick weld consisting of ANY 60- rod and expect strength, also why not follow your original plan? Those jumbled tack welds had ZERO heat in them and you trapped so much slag doing it like that. You cleaned off your tack welds and still proceeded with this other technique. Shabby.
No wonder these kids come in and demand 30 an hour 🤦🏽♂️
I doubt anyone with more than 2 braincells follow this
It’s too cold, going to have lack of fusion and crack😂 Not to mention, you did something COMPLETELY different with the marker😂
As newbie I'm willing to test this out to see how well it holds. I enjoy the video nonetheless 🥰
Положи папин сварочный аппарат на место!
Если положит на место, то никогда не научится, пусть практикуется.
@@berluskoni009 не могу не согласиться с Вами, но стоит и теорию тоже почитывать, а не тыкаться мордой в ж...
Нормально он проверил тонкие трубы.
Every one of those little holes is a failure spot
This had me sick but couldn't contain it and threw up after seeing him leave the spatter around the toes of the welds
😮😅
Horrible
И похер что без зазора , главное сверху налил 😁👍🏻
Да ладно без зазора, шоф то кривой и прогрева металла нет, вот что важно. А варить без зазора допускается . всё зависит от толщины метала. и как фаску снять. но в его случае он насрал без провала.
@@Maxsell96 ну так фаска это и есть зазор тоже)) Понятное дело что жестянку можно без , но от 2 мм толщину уже надо делать зазор
Here's an awesome video of what not to do.
Маркером показывает одно а варит уже другое😮
Ты можешь таким качеством сварки только перед бабульками хвалиться
Никакого провара и прогрева
Для забора в селе пойдёт)
@@penguinkowalski3660 для одноразового бабки срубил и слинял. а найдут в деревне и прикопают.
Ignore these critical losers, even the greatest artists of time were apprentices first learning their craft until the mastered it. Keep learning. You have achieved more than they have with your own channel making your own videos. Keep doing what works for you. Ignore these assholes who have nothing better to do than to tear someone down to make themselves feel better. You’ll become a master welder and make amazing creations so don’t give up. 😊
Your words are touching and beautiful 😊 Thank God for keyboard warriors like you
@@nickmarangos2475 sometimes peoples reactions can be awful to ‘someone starting out’. Don’t let them distract you from ‘your learning and practice’. Stay focused. Practice makes perfect. Try finding blogs, forum threads and research google for welding tips & tricks. It keeps your motivation and inspiration up. You will improve and be amazing. Just keep going. In time people will admire and applaud your creations. 👍 💪
@@nickmarangos2475 I don’t think your grasp the definition of a “keyboard warrior”. Way to expose yourself.
@@TheNarrowPath84 lol Yes I'm truly exposed oh my God Thank you for making me laugh lol
Considering kids that show up high to shop class know better than guy it doesn't bode well for this fella
Варить не научился, но другим уже показывает своё мастерство в кавычках!!!😂😂😂
As a professional welder for 349 years I can confidently tell you that my dogs ex girlfriend can run a bead better than you
Bro draws a weave pattern then shows a circle pattern then ends up doing tack welds. 😂😂
I can see you have a good potential as a comedian, keep going 👌🏻
I think nonwelders just repeat what actually welders say. So many experts online anymore who comment from their race car beds. Keep getting better. I always find it funny when the OGs talk to much shit to the new guy. Just let’s me know how bad they were ragged on when they were an apprentice. They got goofed on bad. They wonder why they cant get any new blood into the trade and why people are so quick to leave the union anymore.
But like you realize this IS a bad weld right? Like im in hs and im in CTE and they literally tell you its a bad weld and show you why
I think need a little bit to improve about your bead
У меня с отрывом лучше получается, чем не отрывая дугу 🙂👍
Came here for all the pseudo-phd-chemist-engineer-welders comments with 198 years experience that have experience building, the Brooklyn bridge, the empire state, and the hoover dam.
That is not a good world
Your entire weld is filled with slag. Good job.
Nice idea👍🏻👍🏻👍🏻👍🏻❤
I really love my own course, welding and Fabrication, and am proud of it
The level of trolling on this one😂😂😂😂
..."Мне пофигу, лиж-бы, ваши размеры сошлись!!!"😂😂😂
Parabéns meu amigo continue sempre assim mostrando seu trabalho
Stacking dimes and doing time ive herd. Life of a welder. Hope to get my D1-5 someday and become a welder.
Рисует маркером одно, а варит с отрывом, такое ощущение что он второй раз в жизни держит держак
Моя бабушка хохотала над сварочным швом, сказала что без зазора даже электрод в держак бы не поставила)))
And if it turned out like I drew it with the marker, there you go almost 😂😂😂
I like how he did three different movements
Que bien maestro para que se enseñan a superarse bien por usted gracias
Why is he doing small circles on a weld like this?
This guy drew a pattern for his tacks,, I seen it all now lord.
Вы бы хоть фильтр поставили или маску перед камерой, а то смотреть на всплески света не очень приятно и понятно.
I knew he wasn't going to do nun spectacular from his prep work 😂
Love your talent 😊
I love how they illustrated with a pen then with the rod then started the opposite way stack welding.....
Bro buffed it off like he was proud 💀
Turn down your amps and move quite a bit faster. Turning down your amps will lessen the over-spray and get rid of those bumps on the edges. If you move a bit faster, your Weld won't have those pores, maybe try a less aggressive rod too
Não sei se vocês já ouviram falar em "bosta de minhoca "🪱, é o que eu costumo fazer com minha máquina de solda.🇧🇷
Thấy bạn Hàn sao mà dễ quá. Mình cũng mấy lần tập tành, tự hàn, nhưng rồi kết quả = hư!!
I studied welding am gonna tell you that he's not that bad, however he needs more improvement to pass the test
Love the simple instructions
С такой под гонкой деталей, отрыв ваще не нужен и глаза меньше устают
I feel secondhand embarrassment right now
Zoʻr chiqibdi
Bros on 5 million amps while using 5/32 on a -2 inch gap☠️
Wow nice
Nice, I am going to try this one this weekend in my shoppe
Brvo❤
Thanks for your support💪
ไม่ได้เรื่อง ไปฝึกมาใหม่ไอ้หนุ่ม
LOL, he shows you his arc pattern and then proceeds to just stitch weld it lol
Bro tried to teach us but fell back to old habits 😂
Большое расстояние от точки до точки, шов не плотный, надо ловить момент когда ванна остывает и 1-2 мм ещё красная, от этой красной точки продолжать процесс сварки
Good job
why the marker squiggles..
Bro just did showed another technique with a marker. And proceeded to do another welding style that isn’t even close the the other😂
Your need a welders smoothing towel 😅
Dibuja movimiento para cordón y termina punteando jajaja 😅 un crack 😊
А ЕСЛИ У МЕНЯ ЭЛЕКТРОД "УОНИ",ТО ЧТО? МЕТОДОМ ПОЛУМЕСЯЦА НЕЛЬЗЯ ВАРИТЬ?😂
Kéo luôn khít vậy Kéo mỏng đẹp nhanh.
Tay nghề của bạn thật sự còn rất yếu. Nên hãy cố gắng học hỏi thêm nhìu điều. Mối hàn như thế này ở việt nam chúng toi không thể nhận được công việc.😎😎😎
หมามันยังเชื่อมเป้นเลยแบบนี้อ่ะ😂
Току меньше и без отрыва ёлочкой, можно даже без задержки по краям
Excelente demostracion ahora porque no les enseñas primero La máquina de soldar y que efectos asé
My stick welder identifies as a mig welder 😅😅😅
Nice even though he tacked it, it was still sporadic
He has the best tac welds I've ever seen. I mean damn, you can't (and they dont) teach that kinda talent. 😂😅
You drew and demonstrated how to run the bead without the gun then grabbed the gun and proceeded to weld absolutely wrong🤣
Experience alone wasn't enough. You need knowledges 😂
Nice
Super jest to pospawane łuskowo i elegancko pozdrawiam serdecznie inwertorowa spawarką czy transformatorową Pozdrawiam jeszcze raz twórcę tego filmu. serdecznie.👍👍👍👍👍👍👍👍👍👍👍