Dodge Grand Caravan Transmission Replacement (62TE) Part 1
Vložit
- čas přidán 12. 09. 2024
- What the Title said.
Please remember, all content that we create is for educational purposes and may or may not be recommended by the Manufacturer. All Videos are "AS IS" We take no responsibility for any Damages or Failures.
* Chemicals can be Dangerous to your Health
* Power Tools is used Improperly can cause Damage
All comments are my Opinion and my Opinion alone, take it as such!
This was a awesome video to watch. Really enjoyed it.
Thank you for detail, it looks like a doable job in my driveway.
How did it go?
@@glennryan646 It turned out I only need engine mounts. There was no problem withmy transmision.
@@uccoskunharder or easier?
Great video!! both Part 1 and 2 were helpful! We just did the job on this saturday on a 2016 Grand Caravan SXT that had no reverse anymore and it took about 12 hours to the two of us, both fairly experimented with car mechanics. Not an easy job but not too complicated either. We had some serious concerns when we tested the car after adding transmission fluid, it was sluggish and the car ahs no power. The problem gradually went away as we added more and more transmission fluid. The car is now working fine however scanning the computer still returns a P083B code LC Pressure Switch Rationality error code and a P0792 Intermediate Shaft Speed Sensor "A" circuit range performance error (unrelated to the transmission). Note that we assembled the tranny back on the engine and had to remove it again because the torque converter was not seated all the way on the transmission shaft. You can tell because the tranny wouldn't come close enough to the engine for us to put the bolts back on.
Not a driveway job however (we did consider it and we backed out of this project) and went to a fully equipped shop with hoist and jack. It was a lot easier, this tranny with torque converter assembled is bloody heavy.
The isolation cover is to deaden the racket that the mopar shift solenoids make.
Very nice video
Nice video! My client's own had a similar issue so I bleed the clutch and still to no avail. I've even replaced only the kit inside the upper clutch but the problem of a sponge clutch and no gear still persist.
I've checked scrutingly for signs of leakage carefully while someone pressed the clutch, i found out that the down clutch nipple doesn't hold clutch hydraulic fluid! It goes out gently, and also the clutch fluid was replaced with a new one. Nevertheless, it's still very darkened in color. Please, how do I fix the issues?
Darkened fluid, soft clutch pedal, and a most especially the leak at the down clutch bleeder or nipple.
I've got the three bolts out of the right side axle. Can't get it to clear the power steering pump. Did you split the shaft to get some wiggle room?
I think using the chain hoist is better then a transmission jack. Did you find easier ?
Every time you can use a chain fall it it going to be easier in my opinion.
I've got to give that a try.
The chain hoist looks makes it look ez, I want to try that too
Good information
How many Hours take to this job finish
Well that depends on skill level and Tools.
thank you.
Did not show how to get torque converter bolds out
If you can't do basics that job is way above your head.
Hey guys, I’ve had a similar issue with my van (2001) 3.3litr v6 I noticed that when I was driving, the van was stuttering and it seemed like it didn’t want to drive nor break and I was only going about 35-45km.
I pulled to the side stoped and turned it off for about 5 mins then I started it drove normal for the first few seconds then it was stuttering again and wouldn’t go past 20-25km so then I turned it off and parked it, after leaving it turned off for awhile I started it and it cranked but then turned completely off in about 20 seconds , then the engine was stuttering and it seemed like it wanted to go but kept on stuttering the muffler was giving out some weird sounds…maybe bad fuel pump?
Transmission gone bad ?
….if anyone can point me in the right direction on what to do….I would grateful appreciate it
I have a question on the shaft which the torque of it goes on to the inner shaft that has the plane back of forth is that normal
I think I know what you are talking about. Yes there is some end play.
@@ralfsautomotive Meant to say the shaft the torque converter its a little loose on The nner shaft is supposed to be Loose it all
Tha k u
I set my new converter and there was some play too
How long does it usually take to do this job?
That is depending on tools and skill level
@@ralfsautomotive plenty of skill level and tools. I have to do this from the ground, just trying to get some information.
@@dealerauctionnightmare4689 if you needa ask, not much skill level.
What are the nifty clips? I don’t have them!!
What Clips? What time in the Video did you see them?
@@ralfsautomotive they want to secure the tour converter small plastic cover
@@ralfsautomotive do you have the part number for the port hole for the torque converter bolt
Thank you so much for this video. Saved me thousands.