@@ImJoeTheCeo So, pardon the novice question then but.... If I'm towing 11K lbs on flat ground then the OD can be utilized with no issues. However when going up grades of any real note, OD should be in off position correct? 1005 F350, 116k original miles, E4OD will be gone through to include all mods for pulling things around. CAT and AIR both deleted. Based on I'll presume your knowledge in things, I'll presume the truck can yank 11K 5th wheel around with little to no issues? Or should I expect to run into something else? Cooling system completely re-done with dual trans coolers added on ( I'm not a fan of burnig down transmissions). I look forward to your detailed reply.
My 1986 OBS F-250 with the 460 did it with 3 cylinders at 60psi. The others were at 100 and 125. Right now it's got a new 7000.00 dollar 468 in it with Eagle H-Beam Rods, ICON Forged Pistons and 1969 429 DOVE-C Heads on it. The Intake is a Weind Stealth. I put a Comp Cams .564/.574 Lift Cam in it with 226/234 degrees duration at .050. 111 Lobe center. I just got it running and broke in the Camshaft. Now I'm putting in the 2nd valve springs. The best part of it is that the Truck only has 74,455 miles on it.
My 76 F 250 Hiboy I call it "The Beast" has a beefed up 460 when I started towing 8-9000 lbs it started breaking things . First my U joints I had to go with a bigger custom made drive line with bigger U joints then the it broke the rear diff. Here in So Cal going up the grape vine doing 60 pulling 8,500 lbs.trying to keep my foot out of trouble.
Sure sounds like a beast! What did u do to beef up the 460? A month ago or so I followed my buddy up the grape vine in my 460, he has a new HD2500 Chevy with a 6.4 or 6.2. Try as I might he kept pulling on me. I need a bit more power for sure! Still made it up tho no issues just a bit slower.
It was a few years back. I took out the stock 390 out to install the 460 (not offered in that year/model) it is a 4 bolt main 060 over, can't remember what pistons , stock crank. with roller rockers and cam (can't remember the duration and lift) I had the stock heads gone through a lot of porting on the exhaust, a Weiand Stealth Dual Plane Intake , Edelbrock Performer Series 750 CFM Carburetor, MSD distributor and a multi spark discharge module also a set of nickle plated mid length headers. So far It has broken my motor mounts , U joints and differential It has a pretty calm Idle though but it will light up 35 inch tires and it's suicide past 85 mph (old 4x4 suspension) it gets 13 to 3 mpg
I watched this video and immediately started having deja vu. That sure looks like highway 152! Then I saw the sign for San Luis Reservoir and it all made sense. I haven't been down that stretch of road for 12 years, but it's still very familiar. I think I have a very similar truck, but I haven't done any heavy towing with it. As others have mentioned here, turn off the OD, especially on grades. You might have to slow down a bit, but the truck won't be struggling as much. Mine has the 4.10 rear end. What's your axle ratio?
I am about to embark on a pretty crazy schedule of 460 swapping my 03 crown vic. Shooting to have a turbo kit ready for this summer. Plan being to tow my fun deck hurricane or some jet skis. Will be going through a bunch of mountain hills, so I am curious if the turbo will help. What transmission do you have? I have already sorted the braking kit out, so I will be able to stop with whatever the build is rated for.
It is amazing how much cooler it will run and use less gas at 3/4 throttle versus WOT. When towing with my diesel I rarely go full throttle and use 3/4 on the hills
That's how they burn up, pushing od button to off is the same switching it to tow haul mode on a modern truck, it increases line pressure, firming up the shifts and it downshifts as you slow to a stop adding engine brake effect, along with locking out 4th gear
Possible reason for a jump in RPM while only gaining a few MPH… transmission getting warmer. Hydraulic oils do not like heat. Torque converters are less efficient… engines spins faster with less torque moving to driveshaft.
@@joshfernandezthediycarguy443 just keep that tranny oil changed regularly.. the ring gears and clutch paper love clean, sticky fluid to hold onto. I’m a 7.3 guy now… but my father was a diehard 351/400/460 guy. In my 50’s now. Spent my younger days doing maintenance on the Ford lineup.. lol Glad you’re getting some good use outta the 460.!!
Don’t use overdrive when pulling anything you’ll get better results and better fuel mileage
Thanks for the advice! I'll do that next time!
Just what I was going to say OD is not for pulling.
@@dgun6924 then what's it for?
@@joshlower1its for normal driving to get better mpg. when you tow, you should not use OD on hilly areas. OD is fine on flat grounds.
@@ImJoeTheCeo So, pardon the novice question then but....
If I'm towing 11K lbs on flat ground then the OD can be utilized with no issues.
However when going up grades of any real note, OD should be in off position correct?
1005 F350, 116k original miles, E4OD will be gone through to include all mods for pulling things around.
CAT and AIR both deleted.
Based on I'll presume your knowledge in things, I'll presume the truck can yank 11K 5th wheel around with little to no issues? Or should I expect to run into something else?
Cooling system completely re-done with dual trans coolers added on ( I'm not a fan of burnig down transmissions).
I look forward to your detailed reply.
My 1986 OBS F-250 with the 460 did it with 3 cylinders at 60psi. The others were at 100 and 125. Right now it's got a new 7000.00 dollar 468 in it with Eagle H-Beam Rods, ICON Forged Pistons and 1969 429 DOVE-C Heads on it. The Intake is a Weind Stealth. I put a Comp Cams .564/.574 Lift Cam in it with 226/234 degrees duration at .050. 111 Lobe center. I just got it running and broke in the Camshaft. Now I'm putting in the 2nd valve springs. The best part of it is that the Truck only has 74,455 miles on it.
Things gotta be a beast!
I want to add aomw more power but keep it as reliable as I can... thinking intake, headers a bigger exhaust
Sounds mighty nice.
Depending on the axle ratio, that truck was only rated to tow maybe 9k or 10k pounds.
Where can I find the axle ratios?
@@joshfernandezthediycarguy443
Usually on a sticker inside the driver's door jam. Then look the codes up online.
Another great video cuz! Keep it going!
Yessir! Thanks for the support primaso!
My 76 F 250 Hiboy I call it "The Beast" has a beefed up 460 when I started towing 8-9000 lbs it started breaking things . First my U joints I had to go with a bigger custom made drive line with bigger U joints then the it broke the rear diff. Here in So Cal going up the grape vine doing 60 pulling 8,500 lbs.trying to keep my foot out of trouble.
Sure sounds like a beast! What did u do to beef up the 460? A month ago or so I followed my buddy up the grape vine in my 460, he has a new HD2500 Chevy with a 6.4 or 6.2. Try as I might he kept pulling on me. I need a bit more power for sure! Still made it up tho no issues just a bit slower.
It was a few years back. I took out the stock 390 out to install the 460 (not offered in that year/model) it is a 4 bolt main 060 over, can't remember what pistons , stock crank. with roller rockers and cam (can't remember the duration and lift) I had the stock heads gone through a lot of porting on the exhaust, a Weiand Stealth Dual Plane Intake , Edelbrock Performer Series 750 CFM Carburetor, MSD distributor and a multi spark discharge module also a set of nickle plated mid length headers. So far It has broken my motor mounts , U joints and differential It has a pretty calm Idle though but it will light up 35 inch tires and it's suicide past 85 mph (old 4x4 suspension) it gets 13 to 3 mpg
I say it did great especially with bigger tires!
460 will handle anything so long as u got the cooling system and gearing to match
Truck is tough for sures!
Ok 460 was a champ as expected
It runs buttery smooth at 162k! Hope it gets to double that before I get any real issues!
@@joshfernandezthediycarguy443 would you know a good power combination for 460efi power
I watched this video and immediately started having deja vu. That sure looks like highway 152! Then I saw the sign for San Luis Reservoir and it all made sense. I haven't been down that stretch of road for 12 years, but it's still very familiar.
I think I have a very similar truck, but I haven't done any heavy towing with it. As others have mentioned here, turn off the OD, especially on grades. You might have to slow down a bit, but the truck won't be struggling as much. Mine has the 4.10 rear end. What's your axle ratio?
Ah gotcha! Will do and thanks for the advice!
What were the RPMs?
My 96 f250 7.5 5speed pulls like crazy uphill, I rarely have to take it out of 5th gear.
Is that while towing tho?
I got the c6 transmission behind my 460... The true Godzilla is the 460
changing to larger dia tires changes the gear ratio, try pulling that weigh same hill w stock tires.
Ah, I got it! No wonder she was struggling a bit! Thanks for the tip!
GOOD VID JOSH!!!! PUSH THE OD SWITCH,AND NEVER COMPLAIN ABOUT FUEL IN A 7.5L/460.LOL
Thanks for the encouragement! Glad you guys are enjoying the content. All in all the truck drives extremely well.
Wooooooo boy , get some .
Whohoo yep!
I am about to embark on a pretty crazy schedule of 460 swapping my 03 crown vic. Shooting to have a turbo kit ready for this summer. Plan being to tow my fun deck hurricane or some jet skis. Will be going through a bunch of mountain hills, so I am curious if the turbo will help. What transmission do you have?
I have already sorted the braking kit out, so I will be able to stop with whatever the build is rated for.
No way! Man, that's an awesome plan! Send some footage when done!
Let’s see more videos of your obs f350 and all that you have done to it .
Will do thanks!
Awesome footage bro, reminds me of towing my forest river Evo with my 99 2500 suburban thru the cajon pass. What mountains were you driving thru?
Thanks! I really appreciate that! 152 up towards los banos! How did the burlan do up the hill!?
It is amazing how much cooler it will run and use less gas at 3/4 throttle versus WOT. When towing with my diesel I rarely go full throttle and use 3/4 on the hills
How much weight were you moving?
Not that much had a bike in the back random items in the tool box and the camper. I'd guess about 5k lbs
I'm getting probably 3-4 mpg, what I can tell you is umm I'm not really picking up any speed 😂
Lol your new 2500 is on a different league, my friend!
🫣Waooo sorpresa 🫢 🎉 Hola 👋🏼 sobrino no savia qué tenías videos en tú canal. Te mandó saludos y un fuerte abrazo 🤗
Hola tia gracias!
what was the mpg?
I've been getting about 9 mpg towing. Almost 14 unloaded
That's really mind blowing considering the new v6 Tacoma get about 18
Better than having payment on these new vehicles
Heck yeah!
maybe turn off overdrive
If his foot is on the floor he ain't in overdrive.
That's how they burn up, pushing od button to off is the same switching it to tow haul mode on a modern truck, it increases line pressure, firming up the shifts and it downshifts as you slow to a stop adding engine brake effect, along with locking out 4th gear
Possible reason for a jump in RPM while only gaining a few MPH… transmission getting warmer. Hydraulic oils do not like heat. Torque converters are less efficient… engines spins faster with less torque moving to driveshaft.
Ah gotcha! I did the grapevine a few months back, hauling the same rv it did the same thing. Just kept pulling like a freight train tho!
@@joshfernandezthediycarguy443 just keep that tranny oil changed regularly.. the ring gears and clutch paper love clean, sticky fluid to hold onto.
I’m a 7.3 guy now… but my father was a diehard 351/400/460 guy. In my 50’s now. Spent my younger days doing maintenance on the Ford lineup.. lol
Glad you’re getting some good use outta the 460.!!