Can I ask you would this be capable of welding aluminium sheet 2-3mm thick? I was going to make a HHO welder but this would save me some time but need to see someone try this out. Thanks!
I have some questions that I have not been able to get answered by the manufacture. Can you assist? I need to know how hot the flame is at the tip, how long I can run the torch on one charge and how much heat is put off the sides of the torch? I would appreciate any help I can get. thanks
Just an update, after basically abandoning it since the video was filmed, I used it for about 3 hours tonight without a hitch. The alcohol does seem rust coloured but actually use was great for it. Polished about 500 4" squares....
Senua Osipov варить если с добавлением в бутылку всякой хренотени для понижения температуры пламени пожалуй можно-а резать лучше всего просто с простой водой в бутылке-лично я вообще иридий сплавлял в шарики по 4-5 грамм из кучи "отрубей",добытых из свечей зажигания-и рений он тоже кстати плавит на удивление неплохо-а у него температура плавления около 3180 градусов!
Just an update, after basically abandoning it since the video was filmed, I used it for about 3 hours tonight without a hitch. The alcohol does seem rust coloured but actually use was great for it. Polished about 500 4" squares....
Can I ask you would this be capable of welding aluminium sheet 2-3mm thick? I was going to make a HHO welder but this would save me some time but need to see someone try this out. Thanks!
I have some questions that I have not been able to get answered by the manufacture. Can you assist?
I need to know how hot the flame is at the tip, how long I can run the torch on one charge and how much heat is put off the sides of the torch? I would appreciate any help I can get. thanks
Just an update, after basically abandoning it since the video was filmed, I used it for about 3 hours tonight without a hitch. The alcohol does seem rust coloured but actually use was great for it. Polished about 500 4" squares....
how do I get rid of laser cut lines?
My machine drop the pressure too fast
Do you know what will be the solution?
Thank You
I just got one of these, I have a question about the alcohol? What type to use and how much?
I need the same help please, what alcohol Do y use please
Im like ur computer sir
It is possible to use isopropyl alcohol instead of methyl? Also using bidestilled water instead of destiled water?
I use Denatured Alcohol
Скажите пожалуйста, железо тонкое можно варить и резать? Tell me please, iron thin you can boil and cut?
Senua Osipov варить если с добавлением в бутылку всякой хренотени для понижения температуры пламени пожалуй можно-а резать лучше всего просто с простой водой в бутылке-лично я вообще иридий сплавлял в шарики по 4-5 грамм из кучи "отрубей",добытых из свечей зажигания-и рений он тоже кстати плавит на удивление неплохо-а у него температура плавления около 3180 градусов!
Im like ur video
Where is this Machine available in India
My name rizwan
Im acrylic fabricator.
Im working Qatar
you do realize the entire video is out of focus-right? but you posted it anyway??? mediocrity wins again ! YEA!!!!
Just an update, after basically abandoning it since the video was filmed, I used it for about 3 hours tonight without a hitch. The alcohol does seem rust coloured but actually use was great for it. Polished about 500 4" squares....
Is this essentially the same as a carbon clean machine ?