CO-Z Automatic Motorized Electric Wire Stripping Machine Unboxing & Testing
Vložit
- čas přidán 5. 09. 2024
- Unboxing & Testing CO-Z Automatic Motorized Electric Wire Stripping Machine. The price for this CO-Z Automatic Motorized Electric Wire Stripping Machine is about 200$.
CO-Z Automatic Motorized Electric Wire Stripping Machine: amzn.to/3orV35w
On Amazon's website, this combo kit is listed as: "CREWORKS Automatic Wire Stripping Machine for 0.06"-1" Copper Wires, Motorized Wire Stripper Tool for 7/0-15 AWG Scrap Electrical Wire Recycling, Electrical Tool for DIY Cable Copper Wire Stripping".
All links here are affiliate links. If this video helped you, please consider using my links to support my channel, I will greatly appreciate it. Thank you.
For any of those that are new to motorized wire strippers, there’s a fairly common method of using them, and I think this will cover just about all of it. First of all, do NOT use gloves, as motors and blades have a tendency of yanking on them, pulling your body parts along with it into the destruction zone(ask woodworkers if they ever use gloves, and why not. Bonus for asking ones with missing fingers/appendages). Next, only strip wires 14awg and bigger(bigger the gauge, the lower the number), as smaller wires are just not worth the time it takes, nor the headache to try to get the machine to work on them effectively & efficiently. Then, group all similar sized wire together, so that you only strip that ONE size until it’s completed, then onto the next. Depending on how much wire per gauge you have, let’s say an even amount in feet per gauge, I would start with the biggest, then move down in sizes, as you will accumulate the most weight in the fastest amount of time. Use the hole thats as close to being the size of the wire, and still be able to slip through without much, if any drag/friction. Mount that infeed hole BELOW the blade height, so that the wire will be at an incline when it goes under the blade. With the motor OFF and the blade higher than the wire is big, feed the wire through the hole until it gets under the blade, then drop the blade down onto the wire. Then crank it just a bit more and test. Repeat until copper is able to be separated easily from the insulation, but WITHOUT the copper being cut up into pieces - you’ll regret it if it’s cut up, so go slowly. You dont wanna deal with copper splinters/stabbings. Make sure that the wire is tracking straight out on the outfeed side, as any deviation can lead it astray, “knocking” the wire out of line with the blade, which you’ll then have to rerun through. Happy scrappy hero pup!
It soes state for any gauge wire.
Youre an expert bruv lol tyvm
Literally cringed when he kept gloves on. Wanna keep all my fingers lol.
i have the one whit the breather cap and i put it on the front and oil came out do i have to put more on it ?
@armandocalderob4848 Sorry bro, i havent the slightest idea orf what breather cap you’re referring to. None of my strippers ever had such a thing
Wires twist sonic you hold it while it’s going in it might help. I know your not supposed to have to hold it but. And also out the wire on the channel then set the blade. When Turing the dial make sure it punctures the insulation.
Hi there is a certain way to use this wire stripper. You need to put the wire in from a lower angle. It takes some time getting use to it. I bought the stripmister.
Me also got the strip meister. The 250. Simple enough to operate.
Just do all 1 size wire, then go to the next size.
More like shit master
@@shaunlee8663 I reckon I can design a better one than shitmister....its not very good
@iffy9776 would it be too much to ask, if you would elaborate, instead of just telling people that it’s not good? I mean, really - how often have you listened to somebody’s negative review, and base a purchase (or lack thereof), by hearing them say just that one line, without any reasons whatsoever to back up your statement?
There’s a much easier way to strip Networking wire with itself vs destroying it in the wrong machine for the job
My mistake. The entire video is just how to use this tool improperly
needs better feeders, these do not have much grip. So I feed my wire from the back then around to the front, and pull up on it from the back, so it will ride the feeder and get better grip. After trying different things I found this to work best. Must be careful, fingers are better on your hand than in the machine. I was lucky, gloves took the hit and I still have all my fingers.
That’s an interesting angle, figuratively and literally. Thanks, i’ll test that out, maybe I’ll put mine back into use, simultaneously ran w/my Stripmeister E1000.
There is another video where the guy is using the screw on end off of a tube of caulking that he has cut to a smaller size for the smaller wire and it seems to be working for nhim. Just got mine tonight, have you to take it out of the box. I will let you know how it goes tomorrow.
12 days later….
Don't you all love looking for a video to explain something (I was looking to see about this machine because I found one for sale and know nothing about it) and there isn't 1 word spoken during the video explaining anything??!! I have no idea why people make these videos!!
Literally came for same reason. Still don't know if it's worth the buy. Want to see a scrapper review it
Sir ji ye modal kon sa je
did not strip #12 STRAND JUST SHREDDED IT
You obviously had the blade too low. I did it all the time with this exact stripper without shredding it
The first 5 minutes of this video is just him using the tool wrong
Why is it so noisy
Ok, I will chalk this up to you being a newbie. Read the instructions, first. Most of the failures were mistakes on your part.
Eth vaggalle.... Vayar kittilla...
Don’t like explaining things then
Well that set my mind at rest, meaning not to buy one. Cheers