Upgrading WPL B-1 With dual N40 motors
Vložit
- čas přidán 10. 09. 2024
- www.banggood.c...
I ordered this N40 motors for My WPL B-1 because this machine will pull big load behind it :D
While I wanted to pt it inside I noticed that they are not only longer but much bigger than N20 motors so My mount will not work and I design new N40 mount for N40 motors :)
i think it will also fin for N30 but I don't have that motors to test.
Motors that I have are slow to simulate heavy load behind car :P
Also one motor spin faster and You need to play a little with screws on gears to get better smooth spin :)
here I posted dual N40 motor mount for WPL/JJRC cars :)
www.thingivers...
Music:
00:07 - 08:49
Avalon - Midnight Stroll
/ avalon-midnight-stroll
08:49 - 15:54
The White Shadow - Everywhere (Original Mix)
soundcloud.com...
15:54 - 18:48
Brenticus - Progressive House
/ brenticus-progressive-...
you are one of the best rc vehicle modifier. cheers.all mods are awesome.thank you.
I'm not one of best because people do incredible designs on this cars and I just like to build not play :)
But that's nice :)
These have quite a bit of torque! I run a single n30 through a HBX transmission in my wpl based Suzuki samurai. It’s pretty unstoppable and climbs 45 degrees. This is an awesome conversion great job!! 👍😀
Yes but cheap drive shaft don't give me smooth ride so I wait for theme :)
Adrian202 RC 👍😀
Great informative video, thank you. I have just ordered motors and I am 3D printing motor mounts now. Great work. Subscribed.
THX :)
Hello there, if I upgrade my WPL B36 to 370 Motor do I need to change the Batteries too. If yes what Batteries should I'll use? Thank you.
No, You don't need to change batteries.
Standard batteries are weak (I don't mean capacity) so motor will never have full power but if You want to change battery to LI-PO You need to change all electronic because Lithium batteries need to have discharge protection to protect battery from over discharge that may damage cells
więc chcę znowu mieć wpl 🤤😣 ...
noga armii jest okaleczona 😂 ...
pilot jest spoko 🤩👍
najlepszy adrian202 RC
:)
Your videos are the best I've seen. Thank you, very very informative.
I'ts hard to find information on these motors.
I have the 1:24 deadbolt, and am trying to decide between dual N20 or dual N30.
In another video (i think) you suggested to get the 300rpm.?
Im putting a bunch of weight in upgrades, which motor would you suggest?
Thank you for your creations!
Awesome delivery!
Hey, i just realized that i confused you with someone else with regard to the 300rpm suggestion.
Can you still give me a suggestion on the rpm for a 1:24 deadbolt.
Also, do you know the torque difference between N20 and N30.
Im finding conflicting info online.
Thank you, much appreciated.
@@MrsRabbit8 N30 is longer so will be stronger but I don't have that car so i cant tell You what RPM will be better but remember that N20 and N30 motors are for different voltage so RPM will change depending on voltage but less RPM = more torque because motor turn in same speed but gearing change.
Also We found out that N20 fail over time so You may remember about that.
I wouls chose 6v 300RPM because 6v 200RPM is bit slow but have better torque
@@Adrian202 awesome! Thank you, I'll go with the 6v N30 at 300rpm.
My buddy says i should just use the one line to power both motors, but I'm thinking it will burn it up, so should go with a 5amp or 10amp esc... save the AE-6 Esc receiver combo from burn.
@@MrsRabbit8 This motors consume about 5A on stall so 10A could still be working fine but You can use two ESC with nor problem :)
Hi Adrian, just saw this video with N40 motor. Is 200RPM still recommended for crawler RC? Is N40 much better than N20? If so, I might just go with N40 motor. 😀 For 2S LiPo, do I go with 6V motor or 12V motor?
Also, the motor mount works with MN99S RC right? That’s the model I own. Thanks a lot!
They are stronger but much more slow, so I think 370 metal gearbox is better
Nice work
THX :)
Hey are you sure these aren’t called 050 motors I don’t know for sure but looked into it before and it is all a bit confusing.
You may right, site say it's 13GA050 but there is no other information :)
Adrian202 RC I think all N motors are the same profile just stretched. Common sizes are N10 N20 N30 and N50 and the number is approximately mm in length. Didn’t know you could get the n style gearboxes fitted to 050 motors till this video so thanks!
@@jons6125 I think it's just longer version of N20 but it's much bigger and stronger :)
Hi.nice work.is there a screw that speed can be adjusted.?
Sadly no, You adjust speed with remote.
I will replace that motors with one 370 because gears like to get stuck or break over time
@@Adrian202 bro thank you that u did not let me waste my money and time.
Bardzo fajne wolne przelorzenie. Ilu obrotowe sa te silniczki? 100 rmp?
150rpm jest dla 6v ale one działają na 2s więc jest coś około 200rpm
Trochę wolno ale sa mocne a teraz będę testował ten duży silnik z przekładnią i zobaczymy jak się sprawi :)
@@Adrian202 ja teraz kupilem.370 na przelorzeniu 100 rmp tego chyba nikt nie zatrzyma.
@@mietekmietek6712 ja chyba też zamówiłem tego 370 ale nowa maszyna tylko zawieszenie piórowe będzie miała niemetalowe :D
Does the stock wpl N30 motor holder fit this N40s?
I don't know size of N30 motors but I think they are just shorter version of N40 so if they are they will fit in this mount :)
@@Adrian202 hope it will fit... will try to get more info about the sizing... anyway all your vids are great! Cheers mate.... 🤙🏼🤙🏼🤙🏼
weight of truck?
With all that metal ?? Heavy as hell :D
Nice project 👍👍👍, btw How do you configure the safe button on the Winch function?
When switch is on second position than copy signal from joystick to aux chanel where is witch connected :)
You can also do the same on flysky transmitters :)
@@Adrian202 Can this method be used on tx devo10 & jumper T12?
@@3kpanama45 I don't have Devo10 and that's My oldest remote I have :)
Can you do a video of putting on a winch pls
Sadly I will not mount winch on any new cars :( Winch is heavy and need a lot of modifications to mount it so sorry can't do that :(
Wait ur polish
Yes, I'm from Poland
@@Adrian202 cool me too
What you doing??
About what You ask ??
@@Adrian202 look like you doing more than the motor but you not telling what or why you taking the reat end part
@@ericcxxxx All is in subtitles but people don't read it :)
There is another movie where I show why I put connector on back :)
@@Adrian202 ok I watch it again I see the subtitle. But I have a read disability so it hard for to keep up with it sorry
@@ericcxxxx No problem, I don't like to talk in videos and people always complain about that :)