Full installation of gate opener - co-z kit + wireless keypad
Vložit
- čas přidán 22. 08. 2024
- how to install co-z (generic) gate opener and how to program wireless keypad
I couldn't find a full video of an installation so hope this helps you guys.
Have a question? ask away
Thank you for taking your time to show us the basics. You are the reason that makes CZcams so Awesome!!
Thank you, tried to find a video with all the info that i needed but couldn't find one. So filmed from start to finish to help others 😊
David Tamayo wX
@@jrdaveblah thanks for the video on sliding gate open what do you do when you mount motor on the left side like your cause the book says that the default setting is for right side mounting ..
Nice of you to make the video. However, the adjusting rod at 6:33 installs horzontailly not vertically. The purpose of the device is it allows the owner to adjust the tension/slack in the chain as time goes on.
David, thanks for posting! After 5 videos, you are the only thoughrough one actually showing electrical connections, and programming the keypad etc etc. Thanks alot, will be installing mine today. One thing extra that would help, is to tell viewers how many wires and what size to run for the infrated safety sensors (I guess you didn't install them, mine came w/ a light which is easy to figure, and 2 infrated sensors one has 4 wires the other 2 I think). thanks again.
Thanks for the video, gave me some good information. I installed my unit, took me a couple of days. I was taking my time, but I also had to remove the old 19 year old Eagle 1000; I did not want to spend the $1800 so I bought this CO-Z. If anyone asked me if they can install it themselves, I would say yes if they are 1. Handy 2. Have all the necessary tools. Regarding the necessary tools, I had to use my grinder to custom make brackets for the magnets. I used a chain link remover because the chains that came with the unit were too small; I used my old one but had to shorten it some. I used my 3/8 powerful drill to drill down into the concrete. I had all the wrenches to use for the various nuts. I had special drill bits to drill into the gate rods, the magnate brackets I customized. So, unless you are handy type and have all the necessary tools I would hire some help to install it.
This video is exactly what I needed to help figure out this gate opener. I wanted to use HomeLink and found out that the built-in transmitter will not work and needs another 'homelink bridge' adapter. FYI for those that are looking to use this with homelink
If you used a 'homelink bridge', can you tell me which one exactly you used to make it work with a homelink transmitter
My 2004 F150 has HomeLink and I was not able to pair my remote unit to be able to use my truck's visor buttons. What am I doing wrong?
Excellent Video, very informative. I especially like the detail information on the circuit board and programming.
CO-Z should pay you for this - huge help, used this to install my own. Also great music.
Thank you for this - Super helpful! I'll be installing mine as soon as I can get a little concrete pad poured to anchor the opener on.
Thanks for this video
You help me to install my new gate opener. Full installed with no problems.. thanks so much for your time..
genious thanks for the simple explenation this save me a headache got all my remotes and key pads working owesome!
Great video, I’m right in the middle of this same install. Very informative.
This video has been so helpful thank you so much. My motor is very similar on the outside but the circuit board on the inside is exactly the same. I was having trouble with the dip switches. I now know what they mean. Thank you. Picked up lots of other great tips too 👍
My 1st unit I installed was 3 years ago. They have improved the circuit board connections greatly, like putting in the reverse motor switch, and the push button connections.
Thank you very much, I just installed mine yesterday based on your tutorial!!! 👍
Where did you find the instruction manual? Thank you
Hello just bought this unit… can you tell me if the power cable came with the unit and what other tools are needed for installation thank you
Wow what a great video I enjoyed watching it 🤩🤩
I installed two motors front n back of the hse (100’ ) synced two remotes to each motor . Why do both motors open at the same time if remotes were synced to each motor ?
Go in to each board and hold the learn button down for about 30 seconds and clear all the remotes. Then hit the learn button, and the big button for your primary gate on all remotes. Go to the 2nd control board and do the same except use the small button for your second gate. I got this done for 4 remotes. Your remotes are probably on the same big button so they use the same frequency. Each button has a different frequency so in effect, you could operate 4 gates with one remote. Nobody tells you this but I've spent some time in electronics while working for Pacific Missile Range.
Thanks for the Video. Does it come with a transformer? How did you wire the transformer to the cable that goes to the recepticle. The transformer I was looking at does not have ground connection . I would be using a 12-2 romex with TOPENS DPS180-U Waterproof AC 110V-240V to DC 24V Power Supplier. Any help would be appreciated, thanks
I just installed a CO-Z and everything went well opening and closing, but my delay timing to automatically close works opposite. It opens the gate after 30 seconds. Any suggestions thanks
I also have trouble with the open close function
There's a travel direction switch near the bottom and it's marked forward or reverse just change it
this video was phenomenal, thanks!!
Can i use regular 12/2 romex to wire this?
Thanks good information, I have a Viking vehicular gate operator model R-6 my question is, can I install keypad on this, thanks
thanks for the video. great info!
Thank you so much for this video! Most helpful I have seen so far. I just purchased a home and the previous homeowner only gave me one code (which I reset the way you did in the video). I can't do the second one since I don't know that code. Is there a way to reset both codes if one was lost?
Is the system still working good after 3 years ?
I install infrared sensor the motor don’t open the gate, the gate close de gate😮, what I did wrong?
Thank you very much, was very helpful
What power cord did u use any number
Thanks for the info. Very Helpful.
Do you mind giving some info im installing one just like yours everything works find except when I put pressure the limit switch dosen't stop
How do i connect the sensor, sensor wires are red, blue, green and white
Where can I find remotes for this? Do you have an idea? I have bought from Ali express ones that I thought were comparable, but they are not. Is has been an headache to find remotes for this motor
Amazon
Great video, i wounder if you can spare a copy of the manual? I am helping a friend who lost his copy.
Thank you!
Hi, thank you. Any chance you would be an amazingly generous soul and publish a video of you turning the pages on the manual?
I will if i find the manual
Hi , can I be able to hook it to a wired open close switch
Easily. It's marked on the circuit board.
very useful installtion video !!
Fantastic, thank you.
Podrias suvir un video con paneles solares?
What size are those anchors?
Hi , what is the keypad you used , do you have any link from where you bought it , I bought one but it didn’t work and when I’d try to program it it wouldn’t work and when I’d want to use the actual remote it wouldn’t work and I’d have to program the remotes back
Can you program this to the cars opener?
Can you wire a button to operate the gate? I would like to have one in the house. I know I could just get another wireless remote but I would like a wired one.
Yes. The manual shows the push button connections.
Your the man!
Where is that forward /reverse switch? My gate opens after 15 seconds instead of closing
Have the same issue, dip switch 1 is supposed change from right side to left side motor install...I tried it but didn’t work. Will try changing cable U & V see what happens per instructions on manuel.
Hi, just got mine. When first powered the motor starts straight away is that correct/what do I do?
thanks
Hi Guys,Can I have the measurement from the motor plastic cover to the farthest end of the middle sprocket bearing?
Hi, have you installed a Vervor gate opener?
Does this system work with another remote control such as Genie Universal Series?
I am looking into that as we speak. Please let me know if you found any good results? Thanks
I have this same one but was wondering if i can install led light onto this?
Yes. I recall they have a warning light connection. Should be able to use that, but, really? An LED?
Moved into a new house where the previous owners did not leave us the remote controls for the Py600Acn gate. I went to Home Depot and bought 2 Genie universals. I’m having trouble programming. Are they even compatible?
leva peace no they are only compatible with the co-z remotes that you can purchase on eBay and Amazon
Did you install a sensor?
No but you can. Just look at your manual
@@jrdaveblah I haven't bought it yet. How's it holding up? Would you recommend it?
How did you attach the keypad to the piece of wood? Also, do you know how to change the batteries on the back side of the keypad? Please let me know. Thank you! :)
I typed this before getting to the end of your video to see about the battery replacement.
At 4:21 you show part of the page for the control board wiring. Do you know where I can find that? We don't have the manual but need to find that page describing the control board wiring.
I dont have the manual but i have found the same one but with different brand names on them on google
Do you know if I can order the harness and computer alone?? Mine got burned but motor and trans is still good. THANKS
No i dont. I got mine from Amazon plus the warranty
Can you send the link to where to buy the whole system?
I get them on eBay
What size concrete drop anchors are those?
Good job bro
How do you program the remotes?
Bracket that holds chain to gate should be horizontal NOT vertical
Im having trouble with mine. It keeps opening up on its own, any help is truly appreciated.
You probably have a timer for it to close after a few seconds and your reverse switch might be on the wrong position. So when your gate is close, your motor thinks thats its actually open and then tries to close it but ends up opening it instead. Try checking your reverse switch. If you pause the video at 5:34 you can see the reverse switch on the bottom right side of the screen. To the left of the white relay under the brown and yellow with green line cables.
What do you when the motor is on the left side of gate cause the book says that the default is a right side mounting ? Do have switch wire or something thanks
Manual says to switch motor wires U and V, and there is also an SW1 to change direction.
U and W. Sorry but it is not V.
I got it it has a a switch
Awesome
what kind of wire did you use?
Great video. Any chance you can do a video on how to add an enforcer photoelectric beam sensor?
I would but i didnt buy the sensors
Can you install two keypads on this unit ? One on each side of the fence ?
I would assume so. think of key pads and remote openers as just devices that send out a signals. the gate opener can remember many signal devices . also i forgot to mention that the 1 key pad can open 2 different gates or the same gate with 2 different codes. this is helpful if you have renters because you always have the master code and can change the 2nd code if renters change.
15amp breaker or 20 amp ??
Replacement fuse how to
Como conectar a batería de carro con panel solar
So you split the power from an outlet?
You can but i have it on its on a breaker with lights on the same circuit
Have u had any problems with the gate opener so far??
No problems yet
How much is the cost of the machine
They are 2 to $300 on eBay.
hello , i Have a question . How do I set up automatic close in 15s ?
See video at 5:15
Were you able to program a car gate opener to this unit? Or does it only work with the remotes? Thanks
I have not tried it with other remotes but the frequency does matter
David Tamayo ok thanks for the quick reply.
when I use the key to make it manual to open my gate it wont move when i try to open my gate manually
For the one in the video i turn the key to unlock the handle, then you flip the handle open towards you
@@jrdaveblah thank you mine was stuck with debris that's is why I couldn't pull it towards me all the way
Hard to see the learn button
My wire are black white and brown? Can't get it to turn on
Mine runs on 110v electricity which is 1 hot, 1 natural, 1 ground wire. If your electrician is trying to run it on 220v electricity make sure that your machine can take it. Mine did not and the motor burned making me buy another. The colors dont make a difference but the way you wire it does
And how does it go on the breaker u have any idea
@@jesssevela5133 hot wire goes on the braker. White (neutral) wire goes on the neutral bar. And your green ground wire goes with the other ground wires and sometimes along with the white neutral wires
@@jrdaveblah i only have red and black wires where can I hook up the ground? Ty
How can I disprogram the control
Hold the learn button down for about 30 seconds to clear all remotes. I think that is what you are trying to do.
Is it a 110v or 220v system?
110. The listing on Amazon says 110-220 but i hooked up my 1st motor on 220 and it burned right away.
Why give assembly information when it available in manual we need information how you assimilate the manual information to your installing situation
Gate