Three round bursts on DSGs are a thing of beauty. Going to be doing an extremely similar build in my UTR45 soon, this was a great way to gauge about what I should expect out of it if I manage to do everything correctly.
@@wyshtechairsoft Waiting on mine from Shapeways. It's a 5T so ideally the inner barrel is around 130-140mm, found a 141mm. (5/16*425mm) On my 5T DSG I needed a needed a MS210 SP to hit 1.1j. Using a 3mm Tungsten rod to keep things solid. Can't wait for it to arrive.
@wyshtechairsoft My 5T DSG with my 39k Rocket brushless on 11.1v 35c 1300mah does 58rps, so maybe around 75-80rps? Heavily doubt it, but I can dream. I had PME with 5T 39k 14.8v so that's a no go. (Actually destroyed my piston. Ordered a new one from Airsoft Mutation)
Hi Scorpion fans! Thank you for the video! I have an issue with mine, the barrel is wobbling I think, and shots are extremely inconsistent. It is a long version and the barrel is perfectly placed into the silencer. Just for extra information, the barrel is almost protruding out of the silencer, that is how well placed it is. Now, I changed the hop up joint/rubber and even the barrel but I still face the same issue. I even tried with the original barrel but still, I face the same issue. What could be the cause and how can I fix it?
Hey man nice video, question: did you really need to do the motor and mosfet mod for DSG ? would this work on stock (motor and mosfet)? I would hate to be wasteful
Yes, this was because the Leviathan offers more quality of life improments and the motor is extremely efficient as its a brushless motor. Batteries last alot longer compared to using a High torque brushed motor.
I'm doing a long range build like a light light machine gun😅 400mm barrel with a custom angel thunder drum mag. My board fried so I just ordered a leviathan and some 16:1 gears as the middle gear broke a tooth. I have the cnc hopup, bb sping guide and short trigger already installed. Any recommendations for my mid range scorpion built for big outdoor games.
Put a full cylinder in and use .32g bbs. That'll increase your range for the outdoors. Short stroke the sector gear on the release side by two teeth. This will help with tappet plate timing, improve trigger response, and help prevent PME in case of a bb jam. Sometimes, this can increase the fps depending on if the tappet timing was off from the beginning. I got a video coming that will explain this in more detail using a SR25 as a reference.
That plastic spring fps washer is a bad idea on a dsg, could hold up to the m150/ 8/1 sector gear. M10 split washer are the same diameter for krytac and vfc is case anyw9ne is wondering
I do all the time. Pricing varies depending on your goals. I charge labor plus parts to reach said goal. Visit the link on Wyshtech Building you a gun in the description and fill out the form on the details of what you're looking to get done.
@@wyshtechairsoft thanks brother, honestly I’ve been wanting to dsg my evo for a long time and I was trying to find someone that has experience with this gearbox!
@Ryan-kx1pn certainly! I can copy and paste the build in the video into your Evo. The only other upgrade made on that Evo in the video was the hopup unit. I ended up installing a Maxx hopup in his Evo and it made life alot easier and more reliable when it came to adjusting the hopup. Not to mention hopup consistency was improved as well.
@@wyshtechairsoft honestly that’s exactly what I would want brother, don’t worry I wouldn’t have any intent on keeping the stick hop up😂, I would most definitely go for an after market one. I am getting all the internal parts in at the end of the year in about a month and a half, so all you would have to do is install, would that work?
Three round bursts on DSGs are a thing of beauty. Going to be doing an extremely similar build in my UTR45 soon, this was a great way to gauge about what I should expect out of it if I manage to do everything correctly.
Thats awesome! You should share your build in the Wyshtech Discord "community builds"!
Noice! Now I am not the only one!! My next goal is the TSG! Great work as always!
I wanna try my hand on a tsg some day. Hehe
@@wyshtechairsoft
Waiting on mine from Shapeways.
It's a 5T so ideally the inner barrel is around 130-140mm, found a 141mm. (5/16*425mm)
On my 5T DSG I needed a needed a MS210 SP to hit 1.1j.
Using a 3mm Tungsten rod to keep things solid.
Can't wait for it to arrive.
Holy crap. How much rps are you going for?
@wyshtechairsoft
My 5T DSG with my 39k Rocket brushless on 11.1v 35c 1300mah does 58rps, so maybe around 75-80rps? Heavily doubt it, but I can dream. I had PME with 5T 39k 14.8v so that's a no go. (Actually destroyed my piston. Ordered a new one from Airsoft Mutation)
Hi Scorpion fans! Thank you for the video!
I have an issue with mine, the barrel is wobbling I think, and shots are extremely inconsistent. It is a long version and the barrel is perfectly placed into the silencer. Just for extra information, the barrel is almost protruding out of the silencer, that is how well placed it is.
Now, I changed the hop up joint/rubber and even the barrel but I still face the same issue.
I even tried with the original barrel but still, I face the same issue. What could be the cause and how can I fix it?
Are you asking about the inner barrel wobble?
I cut down a long shaft warhead to put into my Cyma Galil. It’s not too hard just need an angle grinder and a big deep breath
Ive had to do this. Haha. Were you able to get it to work in your Galil?
Hey man nice video,
question: did you really need to do the motor and mosfet mod for DSG ? would this work on stock (motor and mosfet)?
I would hate to be wasteful
Yes, this was because the Leviathan offers more quality of life improments and the motor is extremely efficient as its a brushless motor. Batteries last alot longer compared to using a High torque brushed motor.
I'm doing a long range build like a light light machine gun😅 400mm barrel with a custom angel thunder drum mag. My board fried so I just ordered a leviathan and some 16:1 gears as the middle gear broke a tooth. I have the cnc hopup, bb sping guide and short trigger already installed. Any recommendations for my mid range scorpion built for big outdoor games.
Put a full cylinder in and use .32g bbs. That'll increase your range for the outdoors. Short stroke the sector gear on the release side by two teeth. This will help with tappet plate timing, improve trigger response, and help prevent PME in case of a bb jam. Sometimes, this can increase the fps depending on if the tappet timing was off from the beginning. I got a video coming that will explain this in more detail using a SR25 as a reference.
Is that the soft air tpavp or the xpavp piston head?
Its a soft air POM Silent Piston head.
That plastic spring fps washer is a bad idea on a dsg, could hold up to the m150/ 8/1 sector gear. M10 split washer are the same diameter for krytac and vfc is case anyw9ne is wondering
It hasnt broken or show signs of stress.
Is it a reliable build?
So far, yes. This is my buddy's Scorpion that he uses now and hasnt had any issues.
@@wyshtechairsoft Nice!!! Is there a warranty that you give after building these guns in case they break down within a certain amount of time?
Do you build guns for people, if so how much?
I do all the time. Pricing varies depending on your goals. I charge labor plus parts to reach said goal. Visit the link on Wyshtech Building you a gun in the description and fill out the form on the details of what you're looking to get done.
@@wyshtechairsoft thanks brother, honestly I’ve been wanting to dsg my evo for a long time and I was trying to find someone that has experience with this gearbox!
@Ryan-kx1pn certainly! I can copy and paste the build in the video into your Evo. The only other upgrade made on that Evo in the video was the hopup unit. I ended up installing a Maxx hopup in his Evo and it made life alot easier and more reliable when it came to adjusting the hopup. Not to mention hopup consistency was improved as well.
@@wyshtechairsoft honestly that’s exactly what I would want brother, don’t worry I wouldn’t have any intent on keeping the stick hop up😂, I would most definitely go for an after market one. I am getting all the internal parts in at the end of the year in about a month and a half, so all you would have to do is install, would that work?
@Ryan-kx1pn I have all the parts already on hand as I also own an Airsoft store. All you need to do is send it to our store.