Jeep Chrysler dodge passenger side no heat or AC on one side how to fix gear/blend door actuator.
Vložit
- čas přidán 13. 07. 2020
- This is how I fixed my Jeep grand Cherokee passenger side that had no AC on just that side. Common issue on other Chrysler dodge vehicles. Can be no heat or air conditioning on either side. Ask questions in comments or let me know if this helped you.
Great video. Thank you for posting. Made the entire process very easy. Took less than an hour.
Thanks for feedback. I appreciate it.
Thanks for the post. Been dealing with this problem for awhile. It worked!! Great tutorial. My knuckles got banged up but it was worth it
Thank you for posting!
Oh my God you just saved me $1000!!!. Did it myself in about well I’d say less than an hour.
great video thanks
First off… thank you, I really appreciate your walkthrough and it helped me get to the actuator…but I am still having an issue. My 2011 Jeep Grand Cherokee started blowing room temp air on the passenger side…driver side is fine TG, but I’m in Florida and it’s too hot to have AC issues! So I checked the blend door actuator and yes…the plastic gear broke off at the stop…and even though I didn’t need it I decided to replace both the actuator motor and the gear with new OEM parts just to be done with it for under $50. So I believe I installed the parts correctly, it can only go in one-way right? Before I installed it tho, I manually tested the door first and it moves freely…I also tested the motor and let it dangle while I powered on the car…I tried holdingon to it to see if some resistance would stop it like the gear stop is supposed to do right? Wrong…that motor did not feel like it was going to stop, or am I missing something here? Shouldn’t it stop with some resistance? Anyway…I really had no other alternative other than to just install and test it …and so I did just that and I’m pretty sure I installed it correctly…it can only go in one way right? I slipped on the gear to the inner gear 1st…with the large tooth to the large gap…then adjusted the actuator/stem to line up and screwed it down. I’m wondering if this is the point where I didn’t line it up correctly somehow. So after installing the actuator/gear and removing battery power for 30 min to recalibrate…I cranked it up and all I can hear from the actuator was a loud clicking noise like the plastic gear just sheared off the stop again! I don’t think I need to pull it off again to figure that out as its exactly the same…cold air on the driver and room temp on the passenger side. I’m puzzled as to why when I crank up the heat on the passenger side that works with no problem…it just doesn’t get cold when I crank it down! I don’t wanna give up yet my bruthas…any help would be appreciated….thx again
Pro tip for the non pro: change the cabin air filter while you have access to it, super easy. Fabrese makes some good smelling one now too. Haha.
Great tip with using the right angle Torx ratchet, saves time instead of having to remove the bottom vent pipe
Pat, last year I referenced your video to replace my driver-side blend door actuator, very helpful! This time I have an issue with my mode door actuator and was hoping you knew if it is located on the driver or passenger side? At 3:33 in this video I see there's another "pink dot" up and to the right of the passenger blend door actuator. Is that the mode door actuator?
Hi sorry for my english when i plug back the big black part that think turn only one ways they dont suppose too turn two Side
Thanks a million replaced the gear, disconnect the battery, still nothing switched from hot to cold while I had my hand on the gear to feel it move and it felt like it finnaly popped in place cold air on both sides thanks again . Noticed you have a aftermarket radio iam about to tackle this install would be a great video,did you keep your steering wheel controls ?
Sweet congrats, it's a good feeling to knock it out yourself. So I didn't do this specific one as the jeep came with it but yes steering wheel controls work. Typically there is an extra part you would purchase to keep that functionality and highly recommend it. I alway miss them controls when I don't have them in my other cars.
My dealership replaced my entire leather dash because it was recalled under warranty for delaminating, after it was replaced my driver side stopped blowing cold air. Could they damaged actuator when replacing the entire dash? I have a feeling they will tell me they couldn't have broken it.
I'm so glad I found your video! All the others I found were tearing out the dash completely. I do a lot of my own repairs but stuff around the heater core/ventilation is not my strong suit.
Just for clarification, does the passenger blend door control the rear air flow as well? Thanks again for the great video! I'll be tackling this in the next week or so.
Honestly not positive about about the back seats but I would think so. Happy to hear it helped you. I have another one on driver side issue and it's a little different if it's that side not getting temp watch that video..
@@patmedina1960 Passenger side is the issue right now. Drivers side is working fine. Thanks again!
@@A-AronEggleston experiencing this issue on my 2012 now, back is blowing cold when heat is on, just the same as passenger, so while I'm assuming that you fixed yours already, it's likely on the same module.
The rear, if it has controls, is a separate unit. Replacing the passenger side gear that’s stuck on heat and the AC works on driver & rear. This video definitely helped the process.
Is this gonna be generally the same for a 2016 chrysler 300?
Mine makes a clicking noise for 8 or 9 minutes on start up. Til I get the part can I disconnect so I don't have to listen to the racket? Will I still be able to use my defrost?
AC blows pretty even on both sides but not as cold on passenger side
Does the position of the gear on the actuator matter? It came off as I was pulling the whole thing out.
Swapped it out with success from this video but the heat on my passenger side doesn’t get as hot as my drivers side. Did I miss something or should I try resetting the battery again?
Well, 2011 grand jeep Cherokee constantly blend door gear is been broken.(right/left) what I notice is a soft tar residue material on blend door I believe is the culprit. Any opinion please. Thanks.
Interesting, I wonder if that's something getting to hot in there and it's makes the plastic soft or even melt? Maybe that tar makes things slip out of place. I don't remember seeung a lot of tar in there. Not sure what they did but the new gears I put in held up for quite a while and just sold that vehicle with everything working.
Why did you remove the bottom and side panel? It did not seem like they were in your way. Did I miss something?
With put the gear on the actuator, do you have to put the gear on the actuator a certain way. Do you have to change the temp before putting everything back together?
So I believe it really only goes in one way within a range and then the recalibration by pulling negative battery cable (explained in my other video on this topic) takes car of where it needs to be.
@@patmedina1960 D
Ok video was vey helpfully done but after replacement of the gear still getting hot air from the passenger side. What did I do wrong ? Any info would be greatly appreciated.
So I would try a couple things. First probably less likely is to do a recalibration of it by disconnecting and re connecting your battery, (I explain this in other video about the same issue but driver side so see that in on my channel), if that doesn't work I would check that little module the gear is connected to is broken on the inside (that is what was broken on driver side for me, there are little gears in it that get messed up). If that doesn't work confirm you are getting power to that gear with the wires that go into it via a multimeter if no power maybe a short or fuse or some other electrical issue. Good luck.
How long did this job take you entirely? I’m debating on whether to do this at home, versus taking it to the local mechanic.
My blend door lever was broken as well. How can I change blend door lever also? Thanks in advance
So I haven't seen that in "newer" jeeps but I have seen it in the older ones and actually have a video on how a fixed an old one. On those there was a private seller selling fix kits.
@@patmedina1960 thank you for the reply. I havent seen any video on that. I really appreciate if you share it and the name or web site of the fixing kit seller. Thanks
@@marslan1 sure, go to my videos I don't have many and I dhoengowni fixed this issue on my 99 but Google "jeep actuator door fix" and you will find a lot of info. It's common on older jeeps.
How do you calibrate the actuator?
Great Question
Did you have to line up the gear in the correct spot or no
Yeah, kind of. If slips right into the part that holds it one way it so hard to mess that up.
How do you Reset Battery?
Pull the ground wire on battery for about a minute. I have another video for the other side that explains that a little bit. It's under the seat.
Good video but do not need to pop out those 2 little bottom plastic bottons.