How to Fix P2015 and P2016 Error Code on Audi A6 V6 3.0 TDI (2009)
Vložit
- čas přidán 24. 07. 2024
- How to Fix P2015 and P2016 Error Code on Audi A6 V6 3.0 TDI (2009)
If you're experiencing problems with your Audi A6 (2009), this video is for you! We'll show you how to fix the P2015 and P2016 error code, and keep your car running smoothly. This video is essential if you're having problems with your car's computer system. So be sure to watch it and learn how to fix your Audi A6 (2009) in no time!
Links
US - amzn.to/3LwTput
CA - amzn.to/45Zw4K4
UK - amzn.to/3ZnvgfM
FR - amzn.to/3LwWBGx
DE - amzn.to/3EJUNpJ
ES - amzn.to/3t2cPBa
#AudiA6
#V6
#3.0TDI
#ErrorCode
#P2015
#P2016
#AutoFixGuru - Auta a dopravní prostředky
10/10 video! il be fitting mine tomorrow thanks
good work continue
Good work man! Continue with A6 C6 (4F) 3.0 tdi stuff ... I had to pay over 500EURO and a lot of headache to change the motors with the actuators (the actuators I bought separately) ...
thank you bro , will do . This car is to return for brake pads and rotors too, and a lot of other issues .
Thanks alot for the video, I have 4 cillinder engine is it the same brackets i have to order?
it's a bit different , you can order them too if you follow the link
Hello i have the same problem where i can find the items as you work what did you install there ?? Thank you
hi , please follow the link , you will find it there
Please make a video on how to change/replace oil cooler with gaskets on this specific engine from this video : 3.0 tdi (mine is ASB) ... (I hear that's a pain in the rear end and + ... ) Mine leaks oil and coolant but only if I top the coolant to the level if it's at the limit it doesn't leak coolant only oil :( :( I have some very bad smells
I'll do my best , hope you will fix it soon
I will try to change the gaskets but if the oil cooler is damaged I will change it but it's a lot a work many say and not a lot if "how to" . Keep up the good work@@AutoFixGuru
Hi!
I got the 2015 and 2016 codes on a 2.7 TDI, and even P2004, P2006 which says like: intake manifold membrane stays open, the other says stays closed.
Is this a solution for it too? Maybe it is also dropped down like on your bank 1.
hi , it is perfectly possible . I think you should try this fix first , and delete errors . Drive around after that and see what will pop up , maybe nothing comes back after all . Sometimes because of one problem ECU makes more of them. Good luck :)
@@AutoFixGuru Yes, that will be the first, I've ordered the brackets already. Thanks for the quick answer.
Where is the link for the parts required
Thanks
please look in description
I replaced my actuator with no change, any advice on wiring and how that might be affected. I think everything ohms out to my ECU but then again I'm going to double check. Had a weird wiring issue with my map sensor at the wheel well where the connector attaches driver's side that cleared my flashing glow plug light
have you tried to scan for faults?
@@AutoFixGuru yes, the fault code is P2016
are the connectors in good condition ? sometimes they go bad too
@@AutoFixGuru Well the signal wires seem to be good but I'm going to back probe the ground side, just had an issue with that so it very well could be the issue. Will report back. Also fun fact computer probes they use for Arduino boards and bread boards work really well with back probing the ECU
👍let us know where you've got with it