You can use boat axles to move the motors to the front. This type of plane is best to use a long elastic band for take off power with a small hook on the front. EDFs kick in on 20m/s so run harder.
Positively amazing! Can you please do an E2-C Hawkeye next? I had an uncle who flew them in the navy back in the 80s. Thought it would be so cool to build him a flying model of one, but I can’t find plans for one online and am not nearly clever enough to build on from scratch!
This was another amazing build! I hope you try another one, maybe more powerful edf's? Maybe some aerodynamics improvements are possible? How about relocate battery or motor further forward instead of using ballast? I'm sure you have many ideas on what can be done to improve it, it would be awesome to see another version of B2 👍
Thanks, The problem is on Angle of Incidence, it has to be higher angle on the front than the rear. After this I equipped it with retract landing gear and ROG without a problem, you can see on the opening of RC Aircraft Carrier video czcams.com/video/8e1L6zYoTn4/video.htmlsi=lZPNvkwbNGD-lX5W&t=12
Interesting using water like that, if the bag bursts you lose valuable electronics, I’ve always admired how you show your failures and successes because that’s what scratch building is all about
We were impatiently waiting for the end of the project... You should cover with fine glass fabrics and epoxy resin to gain strength and hide the depron underneath. You have no other runways for take-offs, this terrain is dangerous. I remember a video where it ended badly... And could you launch a vote to choose the next model to make? Subscribers could participate and vote among 10 different planes. And your boyfriend is a great plane laner you should work with him every episode. 🤣👍❤
Hello julius,i love this plane i have build my version with a front motor,with folding propeller,i also use a soundmodule,with sound of a real spirit ,my compliments for your building and designs
@@JuliusPerdana hello julius,you have to wait for the maiden flight,until the wetter in my country (the netherlands)is better as soon as possible i let you now,regards
Hi Julius this is a great project! I use FT foam board to build aircraft, can you tell me the length of the fuselage? I have built your F4 Phothom with prop and will install a 70mm 12 EDF soon.
Hi julius!, what a build you got here!, Congrats! - It´s funny hear the same music as in "X-Jet channel" hehe. I wonder if you got some issues with two different brand ESCs. Very interesting how do you build the attach for the outer wings and the drag rudders, they where really useful in flight? - You will have to do something with that runaway / soccer field sonner or later...
Hey Julius another great build there, just a question, I don't know if I've asked this before, but have you thought about a 3d printer for making parts for your builds? I built a Cherokee from your plans and 3d printed the main undercarriage with sprung suspension, a prop spinnner and some scale fuel caps that doubled as c of g indicators, I've found it absolutely amazing what it can produce and with your design experience it could elevate your builds to another level even though they're excellent now..just a thought
@@ginopunsalan yes I certainly understand your point I was just curious but Julius is so skilled I don't think he could alienate builders even if he did use one
@@MickB235 he would totally alienate them because they would not be able to replicate what he does because he appeals to the budget builder who mostly can’t afford 3D printers and mills and lathes etc. that’s the beauty of his designs is you don’t need complex design or machinery yet if you want to incorporate it yourself you can.
@@madhukarjonathanminj2772 agree with you, just asking a question not saying he should do it to to restrict those without the means at the end of the day it's got to appeal to everyone
You can download the plans on the link below : paper-replika.com/index.php/rc-foam-project/b-2-spirit-bomber-rc-plane Join this channel to get access to perks: czcams.com/channels/64lnLfKm09f13iayaCOX0A.htmljoin Playlist : 00:00 Middle Section 02:35 Installing EDF 70mm 04:08 Making homemade landing gear 09:16 Taxi test 09:59 Continue building middle section 16:03 Outer wing section 19:45 Making drag rudder 22:38 Making cockpit and air intake 26:47 Covering with painted laminating film 37:58 Control surface and decal 41:14 Maiden Flight 42:17 Pusher prop configuration 43:36 Maiden flight #2
Hello julius,this is my build version from your plans,my version as a pusher propeller 4400 mah 4s lipo,and 2 speakers built in from an old television,driven by a soundmodule
Amazing skills!. Julius, the only thing I saw is that you where trying to take off with "spoilers" opened, the split airlerons where is the spoilers positions (1 up 1 down). Awesome work and how you fixed the setbacks.
no, it's because of the angle of incidence of the wing, it's easy to correct it, just make front landing strut taller. You can see on the opening on my RC aircraft carrier video, it takes off without problem.
Hello, I like very much your job, what kind of film do you use to covriing and other question is, only can fly with the drag rudders open? I thougth that only are used opening to drag the side you want to turn and then to fly right both closed
Recently discovered your CZcams channel, some brilliant builds, really inspiring. I have just moved to Indonesia, enjoying the sun. Can you recommend any sources for materials in the Jakarta area?
I love your work :) I'm planning to build F35, from your video and plans. F35 Lighting is one of my favourite Jet plane ever. :) Will you do F-22? (those are my other favourites :))
It’s beautiful… what’s its RADAR cross section? Seriously though, cool build. The real bird circumvented its (rather serious) stability issues and inability to recover from stalls by using a sophisticated, multi-redundant fly by wire system. Did you need to resort to similar measures?
Actually if you look closer, the landing gear door were open all the time, so it acted as vertical stabilizer, so I have a very good stabilization. If you see new my aircraft carrier video, in the opening when I successfully ROG the B-2, it's actually using retract. When I retract that LG, it's start to wobble, and immediately went for landing, it bounced on landing, zooming and stall, it's very unstable plane of without gyro or landing gear door open
The stability of this aerodynamically complex airplane is astonishing. You did a perfect job - congrats for the design
Thanks a lot!
the most beautiful, the most unexpected, the most fun project you will ever do!!
thanks
yes agree
bro is really genius, instead of buying some parts, he makes of his own. Appreciate it.
What a landing! One of the best I've ever seen (and I've seen a few).
Regards Mark in the UK
Thank you
Amazing detail in this build Julius.
Some times things don't go as planned, and thanks for sharing these lessons too. Overall a great success!!
My pleasure!
Wihh keren Bang, andai ada kontes/perlombaan RC Pesawat kayak diluar negeri, pasti Bang Julius auto menang, soalnya top top karyanya
With the setbacks you experienced, it must have felt amazing to get the plane in the air! Great work!
This is a fantastic looking RC model that even flies. I admire your skills building it, hat off!
Thank you very much!
Amazing build and also I can't help but find it funny thinking it probably has the same size RCS of the real B2.
hi Julius, nice work!
And now, to close the circle, the next one is.....B1 Lancer!
You are a genius Julius, I love your perseverance!!!!!
Sir you must have the most tenacity on CZcams
Great job!!
So nice of you
Semenjak tertarik dengan pesawat tempur ahirnya ketemu dengan cenel yg sangat menginspirasi ini, semangat terus om👍
terima kasih udah nonton jangan lupa subscribe hehehe
You can use boat axles to move the motors to the front. This type of plane is best to use a long elastic band for take off power with a small hook on the front. EDFs kick in on 20m/s so run harder.
Great job. I built a B2 as a slope glider and had some success sloping it. I wish I had put pusher motors on it after seeing your success
Very very difficult project! I salute you and your efforts! Lots of good wishes from the Indian Himalayas!👍👍👍👍
Thank you very much!
Great job Julius. once she was in the air she flew really smoothly.
really smooth
👽👽👽👽👽👽👽👽👽
Julius, you are an inspiration to our hobby.
Thank you for so many different builds.
Love your work.
WINGMAN
Good to see stable flight at last..great job.👌
Thanks 👍
I really like the water balance. Great job!!!!!
Keep up the good work all you need is sponsor you are super super talented brother.
I appreciate that!
Pemerintah harus bisa kembangin orang2 pintar seperti ini
Positively amazing! Can you please do an E2-C Hawkeye next? I had an uncle who flew them in the navy back in the 80s. Thought it would be so cool to build him a flying model of one, but I can’t find plans for one online and am not nearly clever enough to build on from scratch!
This was another amazing build!
I hope you try another one, maybe more powerful edf's?
Maybe some aerodynamics improvements are possible?
How about relocate battery or motor further forward instead of using ballast?
I'm sure you have many ideas on what can be done to improve it, it would be awesome to see another version of B2 👍
Thanks, The problem is on Angle of Incidence, it has to be higher angle on the front than the rear. After this I equipped it with retract landing gear and ROG without a problem, you can see on the opening of RC Aircraft Carrier video czcams.com/video/8e1L6zYoTn4/video.htmlsi=lZPNvkwbNGD-lX5W&t=12
OMG an aircraft carrier!
I'm learning lots watching your videos, I'd like to try to make some of your awesome models one day 👍
Respekt vor dieser Leistung und Hartnäckigkeit !!!
Anjay, bang Julius anda inspirasi kita semua yang suka mödel pesawat terbang.
Salam dari Jerman bang, terus berkarya.
Interesting using water like that, if the bag bursts you lose valuable electronics, I’ve always admired how you show your failures and successes because that’s what scratch building is all about
It burst once, after failed on the second hand launch with EDF, and it didn't reach the center compartment. So I did it again with double plastic bags
As usual Julius! You are just an incredible smart guy
I appreciate that! thanks
I should speed up my builts like this, impressive and the effort during maiden, great!
Thanks
We were impatiently waiting for the end of the project... You should cover with fine glass fabrics and epoxy resin to gain strength and hide the depron underneath.
You have no other runways for take-offs, this terrain is dangerous. I remember a video where it ended badly...
And could you launch a vote to choose the next model to make? Subscribers could participate and vote among 10 different planes.
And your boyfriend is a great plane laner you should work with him every episode. 🤣👍❤
Great job. Excellent talented model builder.
Congratulations 👏Félicitations from France 🇫🇷👍👌
Amaizing Om Jul...liat waktu prosesnya enak bingit..sekali lg videonya tak saia skip2x
Trimakasih om
I'm out near Whiteman, see them frequently, would love one !!
Big big Aloha from the island of Hawai eat you. My brother are magnificent, you are a genius, Aloha.
keren om 👍🏻👍🏻👍🏻 ditunggu built model su 57 felon 😁
If at first you don't succeed, try try again! Well done!
Exactly!
Great project. Great looking and flying aircraft. Congrats.
Excelente trabajo, es el mejor de todos tus proyectos amigo!!!!!!! Work excellent my friend, the best fly!!!!!👍👍
really nice work , it looks awesome , great job
Thank you! Cheers!
I love it, great skills, use Gorilla glue for more work time. Hot glue only where needed for tack holding.
That's inspiring for real mate...Nice job!
Thanks a lot!
that looks absolutely amazing, defined deserves a like
thanks
Mantap bro, ternyata membuat bomber B2 Spirit semudah itu..👍
Enak d liat nyatanya klo bukan rc bikin engine nya aja susah
21:43 I love the hidden push rods.
it deserves a paved runway, too bad seen it take off from such rugged terrain.
Hello julius,i love this plane i have build my version with a front motor,with folding propeller,i also use a soundmodule,with sound of a real spirit ,my compliments for your building and designs
do you have youtube video of it? Share please thanks
@@JuliusPerdana hello julius,you have to wait for the maiden flight,until the wetter in my country (the netherlands)is better as soon as possible i let you now,regards
I found this channel through IG such great work brother! Cheers 🍻
Welcome aboard!
Hi Julius this is a great project! I use FT foam board to build aircraft, can you tell me the length of the fuselage? I have built your F4 Phothom with prop and will install a 70mm 12 EDF soon.
Awesome plane and really good work. Congratulations!
Good job! Your an inspiration to the hobby.
I appreciate that!
Hi julius!, what a build you got here!, Congrats! - It´s funny hear the same music as in "X-Jet channel" hehe. I wonder if you got some issues with two different brand ESCs. Very interesting how do you build the attach for the outer wings and the drag rudders, they where really useful in flight? - You will have to do something with that runaway / soccer field sonner or later...
yeah, it helps on turning
Hey Julius another great build there, just a question, I don't know if I've asked this before, but have you thought about a 3d printer for making parts for your builds? I built a Cherokee from your plans and 3d printed the main undercarriage with sprung suspension, a prop spinnner and some scale fuel caps that doubled as c of g indicators, I've found it absolutely amazing what it can produce and with your design experience it could elevate your builds to another level even though they're excellent now..just a thought
If he started with a 3D printer then he will alienate rc builders who don’t have one. Right now, all of his builds are reachable.
@@ginopunsalan yes I certainly understand your point I was just curious but Julius is so skilled I don't think he could alienate builders even if he did use one
@@MickB235 he would totally alienate them because they would not be able to replicate what he does because he appeals to the budget builder who mostly can’t afford 3D printers and mills and lathes etc. that’s the beauty of his designs is you don’t need complex design or machinery yet if you want to incorporate it yourself you can.
as everyone else is saying,the beauty of Julius's designs are that they don't require expensive and sophisticated machinary.
@@madhukarjonathanminj2772 agree with you, just asking a question not saying he should do it to to restrict those without the means at the end of the day it's got to appeal to everyone
Muito show os modelos de avião que você faz sou fanático nisso e sou escrito no canal 👍😃
Amazing build 👍👍👍
thank you
Again, great job ! ✈🛩👍
You can download the plans on the link below :
paper-replika.com/index.php/rc-foam-project/b-2-spirit-bomber-rc-plane
Join this channel to get access to perks:
czcams.com/channels/64lnLfKm09f13iayaCOX0A.htmljoin
Playlist :
00:00 Middle Section
02:35 Installing EDF 70mm
04:08 Making homemade landing gear
09:16 Taxi test
09:59 Continue building middle section
16:03 Outer wing section
19:45 Making drag rudder
22:38 Making cockpit and air intake
26:47 Covering with painted laminating film
37:58 Control surface and decal
41:14 Maiden Flight
42:17 Pusher prop configuration
43:36 Maiden flight #2
Thank you so much sir but I have B2 BOMBER
very cool man you are my teacher haha
Please bro don't mind but really I have b2 link hear check for confirmation
czcams.com/video/zMRg4aL1mLE/video.html
Julius Perdana is my inspiration so not me
Gila, keren banget
Semangatnya itu sangat menginspirasi
Terus semangat berkreasi dan berkarya
Hello julius,this is my build version from your plans,my version as a pusher propeller 4400 mah 4s lipo,and 2 speakers built in from an old television,driven by a soundmodule
Wow, where I can look at it
Another awesome build. Great job!
Thank you 🤗
Kereen om 🔥🔥 project selnajutnya b1 lancer om dengan diy edf pasti keren
DIY EDF ga visible om, mending beli karena EDF susah dibikin DIY, yang beli aja kadang melempem kok, apalagi DIY
Amazing build! Congratulations!
Thank you!
Amazing skills!. Julius, the only thing I saw is that you where trying to take off with "spoilers" opened, the split airlerons where is the spoilers positions (1 up 1 down). Awesome work and how you fixed the setbacks.
no, it's because of the angle of incidence of the wing, it's easy to correct it, just make front landing strut taller. You can see on the opening on my RC aircraft carrier video, it takes off without problem.
@@JuliusPerdana thanks Julius, will have a look at it. Regards, Juan.
Next F22 om atau SU37 yang populer di masyarakat RC Aeromodelling
Hands on banget Jul 👍🏽
Good job,, thats incredible, its amaźing,,really wonderful!!
Thank you! Cheers!
@@JuliusPerdana wow..yore experience is very expensive,.salam satu anak bangsa
Much respect. Wow. Well done
Good job, Nice plane
Muanteb tenan om,,,,,,,, bravo om jul,,,,,,
Superb.You promised you would build c -130 Hercules
I promised, after A-10
Nice work 👏 👌 bro me also make this but not your size but my b2 bomber fly normally with out Rader and really u awesome
with the pusher prop conversion,is it possible to add retractable gear?
Hello, I like very much your job, what kind of film do you use to covriing and other question is, only can fly with the drag rudders open? I thougth that only are used opening to drag the side you want to turn and then to fly right both closed
could you make a pusher prop B-1 Lancer?
Bagus bang sukses selalu saya suka liat video anda
Pilotnya jago, mendaratnya enak banget....
thanks
Recently discovered your CZcams channel, some brilliant builds, really inspiring. I have just moved to Indonesia, enjoying the sun. Can you recommend any sources for materials in the Jakarta area?
It's in Ciputat, google Kurnia Sablon ciputat, thanks btw
Sukses terus om
Very very good job, i enjoy this video
Thank you very much!
Good build ,but make the nose wheel longer and it will give you a more positive angle of attack. it should take off the ground
yes that's also what I thought
Very cool 👍👍👍
Great job looks great!!
Come here from your post in 9gag
Witam jestem z Polski.Piekny model ale szukam pana planu A-10.Pozdrawiam.
Nice build again Julius!
Buen trabajo Juliuz realice también el me 262
Jose Om ini yg di tunggu2 🛩
Great job man N1
Amazing ! Great job !
great work
awesome man ... real fun
Again, another amazing project.
Thanks again!
I love your work :)
I'm planning to build F35, from your video and plans. F35 Lighting is one of my favourite Jet plane ever. :)
Will you do F-22? (those are my other favourites :))
It’s beautiful… what’s its RADAR cross section? Seriously though, cool build.
The real bird circumvented its (rather serious) stability issues and inability to recover from stalls by using a sophisticated, multi-redundant fly by wire system. Did you need to resort to similar measures?
Actually if you look closer, the landing gear door were open all the time, so it acted as vertical stabilizer, so I have a very good stabilization. If you see new my aircraft carrier video, in the opening when I successfully ROG the B-2, it's actually using retract. When I retract that LG, it's start to wobble, and immediately went for landing, it bounced on landing, zooming and stall, it's very unstable plane of without gyro or landing gear door open
Please, Julius, if I would be so kind. I would like to know the computer program you use to design aircraft
thanks
Awesome! Can you share the cutting plans? 😇
soon
Wow! Awesome job!
Sebelum nonton 'like' dulu aja. Sudah pasti suka..
thanks