Thanks! Nice Job! I am about to re-install my pads but I took them out many moons ago… so was not sure I remember how to do those two straps that go from the back of the helmet… your instructions were very clear… though my seem to be corroded closed… DOH!
Thanks for this video - most helpful! 😀 Fiddly job but your vid made the task much easier :0). Nice fresh C3 Pro lid, ready for the road again. 🏍 Thanks & Blessings, D
G8 video - thanks. My C3 Pro is old. Did the inner today following your instructions. Only issue for me is that the zippers are seriously corroded and non operative. So just had to remove the liner from the cheek pads and wash that. I wish I’d known about this sooner. My bad. Anyway - grateful for the steer from your good self.
Thanks for this. Just bought a C4 basic and there is nothing in the manual about removing the liner, which I need to do at least partially to install my Cardo system like yours was. One thing that is bothering me is those two straps at the back on mine don't appear to be attached to anything, which seems a bit weird. Yours appear to be stuck down pretty good.
I can confirm that its the same process with the C3 Pro ( the one with the double intake on the top of the helmet). One question though: What to do if the collar consists of the model with the built in control knobs for the Cardo communication system ? Dry clean?
Thank you for the confirmation. The SRC system replaces the original collar. I’d suggest that you detach the SRC collar and re-install the original one (hopefully you saved it!). Remember to be careful with the pins.
Thanks for the comment. The trick is to find the zipper and open it. You can then feed the straps through to fully remove the liner. Feel free to send me a photo of the issue so I can better understand where you are working. Send to info@pacmototours.com.
Thanks for the clear video instructions! Judging by the colour of the water I probably should have done this a while ago...
Yeah, right! I was a little surprised the first time I did it too. Thanks for the comment.
I appreciate the video. After washing and rinsing, I used a salad spinner to remove the excess water from the liner pads, and it worked flawlessly.
The salad spinner is brilliant!
Thanks! Nice Job! I am about to re-install my pads but I took them out many moons ago… so was not sure I remember how to do those two straps that go from the back of the helmet… your instructions were very clear… though my seem to be corroded closed… DOH!
Thanks for the feedback. Maybe a little wire brush and WD40 will help you open the zippers.
Thanks for this video - most helpful! 😀
Fiddly job but your vid made the task much easier :0).
Nice fresh C3 Pro lid, ready for the road again. 🏍
Thanks & Blessings, D
Enjoy the ride!
G8 video - thanks. My C3 Pro is old. Did the inner today following your instructions. Only issue for me is that the zippers are seriously corroded and non operative. So just had to remove the liner from the cheek pads and wash that. I wish I’d known about this sooner. My bad. Anyway - grateful for the steer from your good self.
Thanks for your comment. I wonder if some lubricant would free up the zipper?
I looked for this video to see how to remove the chin part…no luck. The rest is ok. Good job sir
I don’t think I’ve ever removed the chin part…
Thanks! Didn't realize it was this easy to wash!
Now you can have a clean helmet!
You saved my helmet. I would never found those zippers for the straps :)) Thanks!
I struggled and struggled the first time I tried to wash the helmet liner! Thanks for the comment.
Thanks for this. Just bought a C4 basic and there is nothing in the manual about removing the liner, which I need to do at least partially to install my Cardo system like yours was. One thing that is bothering me is those two straps at the back on mine don't appear to be attached to anything, which seems a bit weird. Yours appear to be stuck down pretty good.
I think those two straps are supposed to be screwed into the helmet. It may be a manufacturing defect.
@@PacMoto oh thanks for that. I better contact the seller
Thank you! Zippers!
Secret zippers!
Great video. The zip had me puzzled 😂
Yeah, it’s obvious once you know it’s there!
@@PacMoto yes newbie biker here feeling like a dumbass lol 😆
I can confirm that its the same process with the C3 Pro ( the one with the double intake on the top of the helmet). One question though: What to do if the collar consists of the model with the built in control knobs for the Cardo communication system ? Dry clean?
Thank you for the confirmation. The SRC system replaces the original collar. I’d suggest that you detach the SRC collar and re-install the original one (hopefully you saved it!). Remember to be careful with the pins.
thank for your great info... it's save my helmet... good job
Thanks for the comment!
Thanks for the video. very helpful
You’re welcome. Thanks for watching.
This was very informative, but I note that you didn't remove the chin padding - is this because it can't be done? Surely not?
Correct, 8Nm
How did the liner hold up? The label actually says just wipe it off and to not soak it
I gently hand wash the liner once a year, so this is the 5th time. No issue at all.
How do I remove the chin part? I can take out the small part. But how do I do the rest?!
Thanks for the comment. The trick is to find the zipper and open it. You can then feed the straps through to fully remove the liner. Feel free to send me a photo of the issue so I can better understand where you are working. Send to info@pacmototours.com.
Can I put it in my washer on 15' cold programe?
I think it is best to hand wash the liner.
I have washed the inner cushions on a 30‘ C program with a mild wool detergent. Came out perfect. The collar I have washed by hand.
@christopheicher2832 Excellent!
every thing is black can not see anything need more light on the procedure to be help full thanks for the try
Sorry about that.