DIY Powerful Bass Amplifier 200 Watts Using C5200 and A1943 With NE5532 IC

➤ In today's video, the power amplifier using C5200 and A1943 transistors with 5532 IC. This circuit can be used for guitars.
➤ Powerful Amplifier 200 Watts Using C5200 and A1943 With NE5532 IC
➤ Copyright © by Share Tech Creative
➤ Follow me: / sharetechcreative…
➤ Follow Facebook: bit.ly/3eEHjNb
➤ 📺 Thanks for watching!
➤Schematic diagram:
photos.app.goo...
➤ Parts Required:
Transistor:
- 2SC5200 x 2
- 2SA1943 x 2
- TIP 41
- TIP 42
- NE5532 IC
Capacitor:
- 33p
- 0.0022uF
- 0.022uF
- 0.01uF
- 0.1uF x 2
- 1uF/50v x 3
- 47uF/50v x 4
Resistors:
- 0.47/5W x 4
- 10R/1W
- 100R/1W x 4
- 220R/1W x 2
- 820R x 2
- 1K x 4
- 1K5 x 2
- 10K x 1
- 15K x 4
- 33K x 2
- 100K x 1
- 50k x 3 potentiometer
- Aluminum heatsink
- Mica pads x 4
- Diode 4007 x 2
- Diode Zener 15V x 2
Power supply:
+35V 0V -35V / 10A transformer
#diyamplifier #amplifier200watt #sharetechcreative

[@Hoseinsaboorizadeh]

Perfect 😉🤩

[@ShareTechCreative]

Thanks

[@elderdonzky3353]

​@@ShareTechCreative ❤😊😮.

[@arthureschner9319]

Thank you for sharing. After building & testing, here is some info for you: Frequency response is not quite flat. Starting with bass & treble both at mid point: Mids down +-2v Rms, adjusting bass & treble pots can bring response closer, but midrange 1-5khz always down at least 1vRms. Also slight distortion on mid - high frequencies (from about 1khz up). Running +-38v, True Power Output = 100W RMS into 4ohm @ 1khz before clipping.

[@Uraim]

Nice info. Those youtube channels not testing out the amplifier real power with Power resistor connected, instaed of the speaker.
Distortion from 1Khz is not that good, isnt it?
Considering that you used +38V and -38V and the output was 100watt on 4ohm load, you got 20Volt on output which means that you had 26% efficiency which is not that good too.
I have built a way different amplifier, its a Quasi class AB amplifier, which is 2 NPN output transistor 2SC2235 (TO220 Package) on +45V 0 It can put out 35Watts on 8.1ohm load 16.9Volts. Amplifier efficiency is 37.5%. Frequency response is not quite flat, due the low frequencies until about 50Hz is -1Volt from the 16.9 Output. Otherwise very negotiable distortion. Its full diy amplifier, on prefboard and no ic used. Amplifier is tested on power resistor, 8.1ohm was a cold state of the resistor, on 21Celsius resistor temperature.
Mine and your project was cool too.
Have you did it all in air soldering, or in prefboard, or you ordered a dedicated circuitboard from circuitboard company?
I did it on prefboard.

[@cesarflores6756]

Exelente amplificador esta potente y sencillo si es apto para diseñarlo perfecto
Gracias, saludos desde GDL .JALISCO

[@joeyscott4299]

Awesome my friend !!! Just what the Doctor ordered ! Nice guitar amp . I can't wait to build one ! Thank so very much for sharing .

[@ShareTechCreative]

Thanks, my friend!😍

[@saktiakhmad37]

Beautiful voice..

[@abdulhamidabdulrazak5190]

I have been looking a powerful DIY Amp that can drive big woofers, midrange, and tweeters to create my own 3-ways DIY Monitor Speaker. Thanks alot SHARE TECH CREATIVE!!! Appreciate your 1 love guys

[@ShareTechCreative]

Sounds great!

[@sarvanahirwar7173]

Kya baat he sir aapke samjha ka tareeka bahut mast he

[@marlongrandettramos2316]

Hola, exelente su trabajo ,muy bien explicado y detallado lo felicito, una pregunta que voltage ya rectificado es 3l recomendado por usted, de antemano muchas gracias.

[@carlosalberty689]

Cara muito bacana esse projeto,,é e mostrado com os mínimos detalhe a montagem,, nós proporcionando uma excelente facilidade na montagem,, parabéns pro canal!!!!!!

[@wiliantejeda8213]

excelente saludos desde Colombia y Venezuela

[@ShareTechCreative]

Hello, friend!

[@libmananchannel]

Hello my friend! Thank you for showing me a wonderful amplifier!
Very interesting! Thanks for sharing! Have a nice day!

[@ShareTechCreative]

Thank you too

[@Darrin-el8gf]

Works 🙂 thanks 👍

[@ShareTechCreative]

No problem 👍

[@honggam2752]

Very very nice music and video happy to see that thank you for sharing good 👍

[@ShareTechCreative]

Thanks

[@gustavoramonheredia8317]

Muy bueno excelentemente explicado la fuente de cuántos volts es y que amperaje Gustavo argentina

[@ShareTechCreative]

You see in the video description

[@michaeltacloban2727]

Nice simple circuit legit

[@ShareTechCreative]

Yes, thanks

[@Susu-enak-w9t]

Amazzing❤

[@LadyStrzygaDiscoversThePast]

Great job my friend 👍👍👍

[@sukadolan2727]

Amazing...👍👍👍

[@ShareTechCreative]

Thanks a lot 😊

[@sajeevsajeev7423]

Sir sir sir what's this... amazing amazing amazing wonderful wonderful wonderful wonderful.. working video is uploaded you sir... congratulations congratulations congratulations to you sir....

[@ShareTechCreative]

Thank you so much 😀

[@gafurjabborov9524]

Понравился ваш видио

[@leonelalvarado4879]

Buenas tardes! muchas gracias por tu aporte! es posible me puedas compartir el diagrama???

[@Bianchi77]

Creative video, thanks for sharing it :)

[@ShareTechCreative]

Thanks for visiting

[@michaelsingh7529]

I noticed the power supply had four capacitors, but no circuitry for the power supply system and the capacitor values.

[@wcmm1970]

great project, bigger sound, assemble inside a carcass of a quasar 1150 that i took in the old iron, just took advantage of the transformer, just needed to be stereo, or do another one like that and put the two together inside the same cabinet. congratulations.

[@ShareTechCreative]

Cool, thanks

[@pankajmakwana4009]

Super sar nice job

[@ShareTechCreative]

Thanks

[@zayanshaikh8454]

wow!!! amazing bro i subscribed you

[@ShareTechCreative]

Thanks and welcome

[@leguimcg7481]

Hola... Muy buen amplificador... Tengo una consulta.. Y para 12 v. Servirá??

[@tatangkurnia5047]

👍pantatis mantap btl dan menajubkn

[@ShareTechCreative]

Thanks

[@boscogustin804]

Gracias tiene buen sonido saludos desde Palmira Colombia

[@e21177]

Tiene la polaridad al revés ya que los transistores A son negativos (-) y los C son positivos (+)

[@bruceandrebazanbrito5932]

Como así ?

[@e21177]

Es que los transistores que llevan letra A son negativos y los C son positivos

[@gurjeetchouhan2833]

Good bass

[@agatamoura5591]

Perfect

[@ShareTechCreative]

Thanks

[@mr.nvpdiy]

Good work😎👍

[@ShareTechCreative]

Thanks ✌

[@jonessoares6896]

Great work sir keep it up and thanks for sharing

[@martinluviano5212]

Muy bien completamente distribuido y eficas gracias

[@IDEBELAJAR12]

perfect amplifier...

[@ShareTechCreative]

Yes, thanks

[@lorenzogandarilla2860]

Fregon tu proyecto felicidades

[@wcmm1970]

thank you very much

[@ShareTechCreative]

You are welcome

[@Tariqlhr9]

(12:30) Dear in the video you connect 1uf Capacitor to pin3 ( but not clear that is pin3) but down you wrote pin5. Please clearify the pin because I count the pins from both sides but it's not pin number 5. My amplifier is working perfect. The only problem is over heating. My amplifier is heating so much and so fast.

[@ShareTechCreative]

Pin 3 is correct.
It works well and you do it right!
The problem of overheating:
1 / You supply (30v 0v 30v) AC the highest for this circuit
2 / You increase the heating dissipation big because this circuit works very hot!
Thank you for your attention. Good luck.

[@Tariqlhr9]

Thanks bro.🙂
By the way how much minimum voltage that we can give to this circuit?

[@ShareTechCreative]

@@Tariqlhr9
(22v 0v 22v) AC minimum voltage

[@Tariqlhr9]

Bro can i use 4558 ic in place of 5532? Because Both ICs have same pinouts.

[@ShareTechCreative]

Yes can

[@wcmm1970]

hello, good morning, I could use the KA4558, because here you cannot find the NE5532

[@ShareTechCreative]

Yes you can

[@taekwondogtf5420]

Друг. ты молодец . Продолжай в том же духе. Россия тебя смотрит)) Можешь повторить один из старых Советских усилителей?

[@petercornell2002]

Interesting, what are your power supply voltages?

[@ShareTechCreative]

Power supply: (-42v ; 0v ; +42v) DC

[@SHakilAHmed-uk1um]

যা যা ব্যাবহার করা হইছে, তা কিনতে গেলে ১০দোকান খুজতে হবে🤔 তারপর দাম অনেক বেসি লাগবে, এর চেয়ে রেডি করা বোডের দাম আরো কম হবে❤

[@wcmm1970]

I can use other resistors, like dividing between the transistors. other projects.

[@ShareTechCreative]

Yes, you can

[@wcmm1970]

@@ShareTechCreative
thank you very much ️.

[@wcmm1970]

hello, I didn't find the resistors of 5wx047ohms anymore, I can put 2 of 10wx0.47 and didivdir for the 2 transistors

[@Herman-xq1wr]

Thanks brother,!!! Very impresive

[@ShareTechCreative]

Thank you

[@zeeshanawaan5351]

That's a perfect amplifier for me , thanx alot for this amp,
Very well work

[@ShareTechCreative]

Glad you like it!

[@jozsefbodor333]

👌👌👌👍

[@carlosabreu2644]

amigo, que recomienda en cuanto a calidad y rendimiento. un amplificador de esos clase D que estan usando mucho en videos, ohh hacer uno con transistores 2sc5200 2sa1943

[@proaudioteknik7460]

Mantapp jadi terinspirasi,😀😀😀😀😀😀😀😀

[@akuahmadyani5919]

👍🏻👍🏻👍🏻the best thanks🙏🏻

[@ShareTechCreative]

Welcome 👍

[@severinonazario8596]

Muito bom parabéns

[@ShareTechCreative]

Thanks

[@bkmobile6037]

How many volts of battery power

[@wijayasirimadawanarachchi5261]

GOOD

[@sabinianovillena2510]

pls. demo with power supply to complete DIY on that amplifier sir...can?....perfect diy

[@ShareTechCreative]

Please wait

[@ShareTechCreative]

I'll be back as soon as I can. Thanks

[@peteronel4051]

Fantastic amp could you show circuit diagram difficult to work if the cell phone regards Peter South Africa

[@edyjayamusik779]

Nyimakk lorr👍👍👍😍😍🙏🙏☕☕

[@yameteeoniichan2501]

Sir i made this circuit and the sound is really good but the transistors gets extremely hot when its on ideal could u help me please

[@ShareTechCreative]

It works hard so it gets very hot, please increase the size of the heatsink

[@sapchanel2239]

super

[@ShareTechCreative]

Thank you

[@antonioteixeiradasilvianor1552]

Muito bom

[@ShareTechCreative]

Thanks

[@yourethebest7345]

Why you made output using Collector configuration? Output using Emitter configuration is best wattages

[@davidjose4540]

Eu ver. Esquema amplificador

[@wcmm1970]

hello, I didn't find the resistors of 5wx047ohms anymore, I can put 2 of 10wx0.47 and didivdir for the 2 transistors

[@niyonsabaandre3519]

Good

[@ShareTechCreative]

Thanks

[@sureshchathuranga9731]

Good job 👏👍

[@sureshchathuranga9731]

In put 12v how to amp

[@sureshchathuranga9731]

Big capacity how uf capacity

[@ShareTechCreative]

Thank you! 😃

[@craneelektrisyan5530]

Sir thanks for sharing, can i also request sir for pcb lay out hehe thank you sir more blessing to come.

[@gustavoramonheredia8317]

Pregunto y disculpe mi ignorancia , la fuente de 35 mas 35 por diez amperes es cinco por cada polaridad o sea cinco amperes negstivos y cinco amperes positivos

[@ShareTechCreative]

Yes can, including some due to heat generation

[@gustavoramonheredia8317]

@@ShareTechCreative un millón de gracias sr,

[@wcmm1970]

hello, good night, I would like to use 2 amplifiers in one, I use the KA4558. 1 just this normal, more wanted to use 2 stereo, u would have how to help

[@ShareTechCreative]

Yes, you can

[@wcmm1970]

the resistance of 820ohms is heating up a lot is black, I can change it to an 820 1w

[@ShareTechCreative]

Yes right

[@wcmm1970]

the resistance of 820ohms is heating up a lot is black, I can change it to an 820 1w

[@ladjkaoz]

great project.
do you have any porjects for a unit of about 150+50 the amp unit went bad on one of my Pioneer monitors and im planing on remplacing the original amps with some chines class D off from ebay, but i saw your video and I like it better looks like a more solid amp. also it can be fixable on the long run Vs the chines amps.

[@prashananushka1336]

Perfect ... diagram please

[@adryanarnulfodiazdelgado1594]

Buenas noches el transformador es 30 por cada lado en total seria 60 voltios

[@ademirpinheiro3943]

Quero passar um informação para as
pessoas que estao montando este amplificador, ir traçando um esquema logo na soldagem dos componentes. Nao fica dificil de fazer.
Daí fica mas pratico fazer este protótipo
Abraços , saudaçao de Brasil.👏👍

[@yatinparmar6122]

Sir it is a prayer to you, give PCB layout with each diagram. I will make each of your amplifiers.

[@wcmm1970]

how to unite 2 of these amplifiers and one, using the KA4558, would help

[@ShareTechCreative]

You remove the first Opamp and make the opening for the other channel

[@KOLEJ22DrogaPrzygody]

Hello great video like 👍👀

[@ShareTechCreative]

Thanks for the visit

[@patrykoles4567]

How about low frequencies distortion on high volume? Looks like circuit is "simple".

[@rodrigoantonio612]

buen video no tienen el video de como hacer el amplificador de cuatro transitores 5200 1943 pero para colocarle parlante de 15 si estan amable porque yo tengo uno de dos transitore y quiero agregarle dos mas pero no se como es el diagrama te lo agradesco

[@franciscojavierpinedamunoz2186]

Excelente video entendible por favor ayudame con esto como manejar el tema de los ohmios esn cado de querer un ampli estereo

[@jhayzonnazareno6273]

Gud day sir. I like this diy project. i want to build this in real pcb but i have no diagram. Can i request your circuit diagram? Thank you. From Philippines

[@anyeljosepinalesubiera7007]

buenas saludos broh, es sobre la fuente de alimentación; eso se puede hacer con una fuente de 18 o 24 volt ??? o tiene que ser con esa que usaste obligatoriamente?? ooo se puede conectar los capacitores con la fuente dc

[@asrulgores2611]

The teacher if resistor 0.47 5watt in change that 0.25 5watt Will be safe also.tq

[@ShareTechCreative]

Yes, can

[@asrulgores2611]

@@ShareTechCreative ok tq

[@prathambhatnagar]

At 4:42 u have connected opposite as u have mentioned?

[@ShareTechCreative]

Yes, keep looking at the two diode notation

[@prathambhatnagar]

@@ShareTechCreative thank u

[@ddverum7242]

If you a potensiometer for the mic, which route do you take, please guide?!

[@manuelfonseca9937]

Quiero preguntarte si puedes hacer un amplificador con transistores D 2395?

[@adalbertogarciagonzalez2721]

Saludos brod una pregunta ke fuente de alimentación o ke voltaje usa este amplificador gracias de antemano saludos

[@ShareTechCreative]

Usar Fuente dual (-42V . OV . +42V)

[@danikusumachanel.3082]

Malaysia

[@ashishtomar8303]

sir aapne esme jo supply di hai wo kitne volt ki hai aur transformer kitne 0 kitne ka hai.
plz sir batayen.

[@ShareTechCreative]

Power supply:
+35V _0V_ -35V / 10A transformer
czcams.com/video/14K0Pup260Q/video.html

[@ashishtomar8303]

@@ShareTechCreative thank u sir😊

[@irphankhan6478]

33p kahan pr lagana hai
Please tell me

[@ShareTechCreative]

Parallel with 100k resistor

[@r.kstatusworld2008]

Bhai 2.1 home theater circuit low price me btao pls bhai reply

[@prasundas2226]

One 1943 and one 121 transistor use for one channel is possible...? I want stereo amp only for 2pcs 1943 and 2pcs 121 transistor...please make ....this Thanks...

[@Vicky_entertainment784]

Gujb

[@marcosluizsouza1794]

Better

[@ShareTechCreative]

Thanks

[@reynoldprincipe6966]

good job 👍 like awesome but don't show the voltage.

[@ShareTechCreative]

See in description

[@Jeferson_Alemao]

can I use the 4558 instead of the 5532??????

[@ShareTechCreative]

Yes right

[@frh69]

De cuantos voltiod es la fuente de alimentaciin

[@ShareTechCreative]

Power supply:
DC (+35V 0V -35V) / 10A transformer

[@tonixsswing2093]

Can u give all the parts list,,,,so i can start making ur best amplifier

[@ShareTechCreative]

Check description

[@Vicky_entertainment784]

Transistor ka bass ka sound fattta kiyo hai

[@anyeljosepinalesubiera7007]

I will use Source DC or just AC?

[@thevabhas7225]

Upto maximum dcv can give... Sir.

[@kevinbeats1030]

whats the max voltage for this curcuit? can io use 42 0 42?