I really enjoy how the hatsan jet looks before the mods and love it afterwards its really what I am looking for. A video of how to fix the firing pin would be nice! really a video on all the mods I want that FPE
Hello Andrew. Unless you have access to a metal lathe then you will have to hope Hatsan will send you a new pin/exhaust valve. When mine broke, I made a completely different stem with a new delrin seal. Whole new specs. = better flow. A lot of people want to know exactly what i've done and sometimes, not always, but sometimes I do not like to give away fine details. Ideas run wild in this industry and I hate to see every secret discovered so soon. Enjoy the circus 💪
@@TheFowlerAirgunChannel I see thanks. is the suppressor an ancient Chinese secret as well? I have a jet 1 on the way and from what i found I need an adapter like 1/2 unf?
Did it break from being factory set or did it break after you modded? Really wanting to pick one up after they come back in stock but that comment worried me, and also saw someone else say that it loses lot of pressure after a week sitting idle, have you been able to leave it pumped for a period of time and did you notice that as well? Build looks awesome btw
It's holding air good for me but I also have a custom made valve pin in mine. It never leaked with the factory one however. I do believe that the valve pin is too narrow at the o rings which can not handle any more of a load than the factory released it at. I believe it could withstand a light tune but not much more. I thing it's more like a $200 piece in my opinion but I do like it. And thanks for the support. Enjoy the circus. 💪
@@TheFowlerAirgunChannel i ended up ordering a kral np03 refurbished for $220 i saw you had some videos of that as well seems that got higher fps so hopefully that was a good decision. Haven't got the confirmation email so hopefully my order went through and hopefully I don't get shipped a defective unit lol
I saw your other video on the Sortie right after I asked the question, so that answered it for me. Thank you for the response though. Not too many videos on this gun yet.
756?? How? I see you got a longer barrel on pyramidair from a previous post, and that it's a Kral, can you tell me specifically which it is or post the link? Additionally, I would very happily pay for an example of the custom pin/exhaust valve yours has. Anyway, love the content and subscribed. Keep it up!
Unfortunately Pyramyd doesn't carry this product any longer. As far as the exhaust valve goes, i would have to disassemble the gun to get a picture of that as I do not currently have one. It was a complete work over on the valve.
@@TheFowlerAirgunChannel thanks for responding! What am I looking for in a new barrel? Are there threads and dimensions I should know? If it is at all possible I would love to throw a 12 inch on mine as well, but i cant do any machining where Im at rn
There are better options for the money. But that depends what you're looking for. Its a great pistol for close in shots, not much more. A little inaccurate and a small magazine. Lets just say... I don't pick it up as much as I'd like to. 💪
@@TheFowlerAirgunChannel do you have any mod recommendations for the hatsan 135? I don’t want to diesel the pellets, but I need more power. 600-650fps would be ideal. I’ve pumped the piston back up to 150 bar
Great Job Steven. Your getting 25-26 FPE from that little rifle! Sweet. I hope you can get 40-50 yard accuracy too.
Pretty good energy for a small setup!
I don't know why, but I am fascinated by the 25 cal air gun. Watched 3 vids. Now subscribed. Lol
Sweet! Anything you'd like to know or see me do?
That's a really nice tune.
Thank you 💪
I really enjoy how the hatsan jet looks before the mods and love it afterwards its really what I am looking for. A video of how to fix the firing pin would be nice! really a video on all the mods I want that FPE
Hello Andrew. Unless you have access to a metal lathe then you will have to hope Hatsan will send you a new pin/exhaust valve. When mine broke, I made a completely different stem with a new delrin seal. Whole new specs. = better flow. A lot of people want to know exactly what i've done and sometimes, not always, but sometimes I do not like to give away fine details. Ideas run wild in this industry and I hate to see every secret discovered so soon. Enjoy the circus 💪
@@TheFowlerAirgunChannel I see thanks. is the suppressor an ancient Chinese secret as well? I have a jet 1 on the way and from what i found I need an adapter like 1/2 unf?
@@andrewfelldown yes. Male 1/2 unf to male 1/2 unf adapter. The moderator is a Donnyfl Tatsu 💪😆
Hello what did you do to it and is that a different barrel ?
Did it break from being factory set or did it break after you modded? Really wanting to pick one up after they come back in stock but that comment worried me, and also saw someone else say that it loses lot of pressure after a week sitting idle, have you been able to leave it pumped for a period of time and did you notice that as well? Build looks awesome btw
It's holding air good for me but I also have a custom made valve pin in mine. It never leaked with the factory one however. I do believe that the valve pin is too narrow at the o rings which can not handle any more of a load than the factory released it at. I believe it could withstand a light tune but not much more. I thing it's more like a $200 piece in my opinion but I do like it. And thanks for the support. Enjoy the circus. 💪
@@TheFowlerAirgunChannel i ended up ordering a kral np03 refurbished for $220 i saw you had some videos of that as well seems that got higher fps so hopefully that was a good decision. Haven't got the confirmation email so hopefully my order went through and hopefully I don't get shipped a defective unit lol
@@xisackxdid the Kral np-03 work out for you? Hard to find one at the price you paid. Like to have one myself. Take care man!
What do u think about the power,if you were s burgler ,wouldbit bother you to take a few
My .22 jet has 7 round mags. Where do you get the 10 round mags? Are they from the flash/flashpup?
This one is a Hatsan Sortie magazine I purchased from Pyramyd Air.
I saw your other video on the Sortie right after I asked the question, so that answered it for me. Thank you for the response though. Not too many videos on this gun yet.
756?? How? I see you got a longer barrel on pyramidair from a previous post, and that it's a Kral, can you tell me specifically which it is or post the link? Additionally, I would very happily pay for an example of the custom pin/exhaust valve yours has. Anyway, love the content and subscribed. Keep it up!
Unfortunately Pyramyd doesn't carry this product any longer. As far as the exhaust valve goes, i would have to disassemble the gun to get a picture of that as I do not currently have one. It was a complete work over on the valve.
@@TheFowlerAirgunChannel thanks for responding! What am I looking for in a new barrel? Are there threads and dimensions I should know? If it is at all possible I would love to throw a 12 inch on mine as well, but i cant do any machining where Im at rn
Which pellet is accurate with the stock hatsan jet 2. .25 cal please let me know thanks
Best pellet hands down are the FX 25.4 grain pellets. 💪
The speed means little if we do not have the weight of the projectile. Or did I miss something
It was likely a standard 25 grain pellet
Thank you
Kool... how much it weigh now?
Not sure. Ill weigh it tomorrow
Is this a good buy if you leave it stock? I really don’t want to waste $300 if possible.
There are better options for the money. But that depends what you're looking for. Its a great pistol for close in shots, not much more. A little inaccurate and a small magazine. Lets just say... I don't pick it up as much as I'd like to. 💪
The one I had was a pos out of the box. But I’ve had a ton of bad luck from hatsan. My 135 30cal was machined by toddlers I guess bc it’s junk as well
@WildKermit it's not just Hatsan. That is why I go over everyone of my airguns that I own. Many corrections are often needed. Unfortunately
@@TheFowlerAirgunChannel do you have any mod recommendations for the hatsan 135? I don’t want to diesel the pellets, but I need more power. 600-650fps would be ideal. I’ve pumped the piston back up to 150 bar
@@WildKermit Im about to get to sleep. Long day. I will get back with you tomorrow though. Have a good night 👍