Hey everyone, sorry I never answered any of these comments. It’s been a while since I worked on the drone, so unfortunately I don’t recall how I ended up fixing it... I think HobbyKing still provides live help, so hopefully that could be a path to resolving it.
1) All you have to do is power off both remote and quad. 2) power on the remote with throttle all the way up. 3) press hold those two buttons and power up the quad (do not release the button until calibration gets over ) 4) with the button pressed on quad , lower the throttle all the way down 5) when you hear the buzz sound you are good to go...
you need to off the transmitter to while making throttle stick up you have to power transmitter and copter then power on transmitter and Quadcopter it works
Paarth Saini Well I has been a while since I fixed it, but if I remember correctly, the HobbyKing representative told me to calibrate ESCs, accelerometers and gyroscopes, etc as usual. Then, turn self level ON. Afterwards, let the drone take off and it should balance itself out, hence fixing the motor speeds. If this still doesn't resolve it, I highly recommend using the HobbyKing live support chat which pretty much garantee a good result. Hope this helps :)
Philip Becker Thanks slot for the help but mine worked when I did manual ESC calibration in which I had to calibrate each ESC at a time. Then I calibrated them all with the KK board and now at least three are working together because solders had come out. Thanks for your help. Will check if last motor also works. For doing manual ESC calibration you need to connect each ESC pin to recover throttle then power it on. A beep will come then another beap after throttle is at full. Then pull your throttle down. ESC makes another beap and calibration of the single ESC done. Then do it with all others and then calibrate them with KK board and done. Remember to remove all other Each pins and receiver pins from KK board when doing manual ESC calibration.
Hey first of all go to reciver test and set all the values of throttle rudder etc to zero by moving sticks of the transmitter after that put the quadcopter on a flat surface and calibrate acc after that calibrate the esc that may be helpful
that is not the way to calibrate ESC. Power off Flight controller, power on transmitter, move throttle to top position, hold 1st and 4th buttons of your flight controller and plug the battery wire to the board wire and you will hear 2 beeps and move all the way down the throttle stick and you will hear one more beep and leave the buttons until you should not leave those buttons. i hope this helps .
Hello sir, i built a quadcopter by kk2.1.5 but never flying it because i have facing a problem i.e when i connect battery to the quad and after esc calibration the motors are automatically runs without throttle and also witout arming.....so this is a big strange, what can i do plz help me
First off, you kk2 board is not secured to the copter. You need to glue it or secure it with a cussion in between the board and the quapter. It has to be basically part of the copter to read the g force values of the quadcopter. Second if this problem still happens, you need to reset the board and do the esc, calibration. Either individually or all at the same time. Do a search and you will find a number of videos about that.
Hey everyone, sorry I never answered any of these comments. It’s been a while since I worked on the drone, so unfortunately I don’t recall how I ended up fixing it... I think HobbyKing still provides live help, so hopefully that could be a path to resolving it.
Same here, one of the motors goes slow until goes off and the others just crazy
1) All you have to do is power off both remote and quad.
2) power on the remote with throttle all the way up.
3) press hold those two buttons and power up the quad (do not release the button until calibration gets over )
4) with the button pressed on quad , lower the throttle all the way down
5) when you hear the buzz sound you are good to go...
Are u saying about throttle pass
Thank you very very much bro. Your comment was a relief for me after weeks of failure.
My dron in 2 ESC red and 2 ESC yellow so what should I do?
I have also this. ..issue ... did it solved
you need to off the transmitter to while making throttle stick up you have to power transmitter and copter then power on transmitter and Quadcopter it works
how will hobby king will help for our problems i have the same issue
facing similar problem what should i do any suggessions?
Plzz hlp me. . I have issue with. ..my fcb it doesn't let my quad to fly all the motors are moving with different speed
Thanks
how to connect kk 2.1.5 to FS ct6b receiver
Help....my controller restarts when throttle is above medium
I think you should first press the two buttons and then power on the control board.
Your help is very much appreciated, but luckily I was able to resolve the issue with HobbyKing. :-)
Philip Becker how? i have the same issue.
Use an arduino to calibrate the escs
Can you help I am working on this since a month and I am having same problem
Paarth Saini Well I has been a while since I fixed it, but if I remember correctly, the HobbyKing representative told me to calibrate ESCs, accelerometers and gyroscopes, etc as usual. Then, turn self level ON. Afterwards, let the drone take off and it should balance itself out, hence fixing the motor speeds.
If this still doesn't resolve it, I highly recommend using the HobbyKing live support chat which pretty much garantee a good result.
Hope this helps :)
Philip Becker Thanks slot for the help but mine worked when I did manual ESC calibration in which I had to calibrate each ESC at a time. Then I calibrated them all with the KK board and now at least three are working together because solders had come out. Thanks for your help. Will check if last motor also works. For doing manual ESC calibration you need to connect each ESC pin to recover throttle then power it on. A beep will come then another beap after throttle is at full. Then pull your throttle down. ESC makes another beap and calibration of the single ESC done. Then do it with all others and then calibrate them with KK board and done. Remember to remove all other Each pins and receiver pins from KK board when doing manual ESC calibration.
Hey first of all go to reciver test and set all the values of throttle rudder etc to zero by moving sticks of the transmitter after that put the quadcopter on a flat surface and calibrate acc after that calibrate the esc that may be helpful
Philip Becker which motor are use and which battery are use please please tell me🙏🙏🙏🙏🙏🙏🙏
@@AbhishekMishra-re9zc 1200 kva motor and 2400 mah lipo battery is quit good
that is not the way to calibrate ESC. Power off Flight controller, power on transmitter, move throttle to top position, hold 1st and 4th buttons of your flight controller and plug the battery wire to the board wire and you will hear 2 beeps and move all the way down the throttle stick and you will hear one more beep and leave the buttons until you should not leave those buttons. i hope this helps .
Sir when I did esc calibration the kk screen went off. Only lighting with no text in it. Please help
Miko Dragneel see my channel it has a video on how to solve it
It won't calibrate with a fault. No esc feedback no cal
I have the same problem
Hello sir, i built a quadcopter by kk2.1.5 but never flying it because i have facing a problem i.e when i connect battery to the quad and after esc calibration the motors are automatically runs without throttle and also witout arming.....so this is a big strange, what can i do plz help me
Nihar Ranjan Mahali
May be it's because your remote needs to be calibrated, use trimmer in your remote to control sensitive
Thanks for your suggestion but now i am using sp racing f3 flight controller
I am using ...kk.2.1.5 but it doesn't work...it doesn't flying..all the motors are moving with different. ..speed .and doesn't fly
@@polu871 seme problem brother👦
Change the ESC then it might work
First off, you kk2 board is not secured to the copter. You need to glue it or secure it with a cussion in between the board and the quapter. It has to be basically part of the copter to read the g force values of the quadcopter. Second if this problem still happens, you need to reset the board and do the esc, calibration. Either individually or all at the same time. Do a search and you will find a number of videos about that.
I have the same problem bro. Have u solved it. Pls reply bro
Unfortunately its been too long since I worked on it... Sorry, really wish I could help :/
I am also facing the same problem.
@@musafirkc now I have solved it bro. Trim using transmitter
@@praveen6740 help me
The esc was damaged
How to test that
Becouse the flight controller is rotated please it straght . Your drone triying to yow becouse the flight controller is not straght a line
Hii same problem I am facing have u got the solution
Hello
@@adithyaadiga8736
May I help you
@@lalittiwari2679 bro did u no the soln
@@adithyaadiga8736 yes
@@lalittiwari2679 yes say how to do it
your problem are setting in the remote throttle to the minimum that all motors are start all together my youtube channel itam my fashion and gigs
bhlyaaaaaa. chi