Excellent video. There is a lot in it in a very short time. Great. Will try. I have my first Blynk test succesfully loaded yesterday. This will help me to progress further. Thanks
It is an excellent project, very complete! and above all by adding the IR it collaborates to not depend on the PC or the mobile. It was what I needed. Thank you very much brother!! My board for now only has 4 relays, a dht , and last night I added a PWM control to drive some RGB strips. I have the ultrasonic sensor which I will be adding soon. Thanks again. Greetings from Santa Fe Argentina!!
How you are powering the esp through vin pin or cable also how much power you are supplying then what is the source of power like laptop or lithium battery
Great project Ahmad! I never thought of using an ultrasonic sensor for water level. That will work perfectly for me. I also need a sensor for checking water leakage such as under a sink. Thank you.
Hello Mr Ahmad! Great project here. I just uploaded the IR code into my ESP32 but the serial monitor just keep generating something else and never responded to the presing of the remote. I'm using Bush TV remote or must it be that type (LED RGB) of remote?
Hello, I made the whole project but it has some problem after some minutes it starts turning on and off the relays itself, and some sensors like pir and ultrasonic doesnt work, what can be the problems . Looking forward to your reply Thank you for your amazing projects
Interference from other devices or electrical noise can cause issues with your project. Make sure that your project is shielded from interference, and try moving it to a different location if possible. make solid connection with quality wires
in my blynk console i am unable to add more datastreams. it is asking upgraded version. can uh provide me alternate method or any cracked version of blynk
Good day, I was able to install version 2.0.9 and when i uploaded the "get ir remote Hex" but it was giving me the direct Number I press from 1-4, I got 1,2,3 and 4 directly and rspectively,is it supposed to be so?
Sir actually I'm making my weather station for my village so i have to upload dht11 sensor readings to my own website and with if condition like when temperature is over 30C then readings should display high temperature on my own website so people can visit my website and check temperature (no weather station is currently in our village) so please help me sir i will be very thankful to you
In file included from c:\Users\User\Documents\Arduino\libraries\IRremote\src/IRremote.hpp:273:0, from c:\Users\User\Documents\Arduino\libraries\IRremote\src/IRremote.h:10, from F:\WIFI WATER LEVEL\ALL IN ONE SMART HOME\ALL_IN_ONE\ALL_IN_ONE.ino:115: c:\Users\User\Documents\Arduino\libraries\IRremote\src/private/IRTimer.hpp:1373:50: error: missing binary operator before token "(" #if ESP_ARDUINO_VERSION < ESP_ARDUINO_VERSION_VAL(2, 0, 2) ^ exit status 1 Compilation error: exit status 1 error showing can you help me pls
The error message you are encountering indicates that your ESP32 board is experiencing a reset due to the RTC watchdog timer (RTCWDT). This typically happens when the watchdog timer is not refreshed within its specified timeout period. Here are a few steps you can try to troubleshoot and resolve the issue: 1. Verify the connections: Double-check the wiring connections between the ESP32 board and any peripheral devices or sensors. Ensure that all connections are secure and properly configured. 2. Update the firmware: Make sure you have the latest firmware installed on your ESP32 board. Check the official documentation or the manufacturer's website for any firmware updates or bug fixes that may address the issue you're facing.
I am not very excellent with embedded systems. I'm still a beginner and an enthusiast. These steps are somewhat very technical to understand fully. But I think I installed the latest ESP32 board (2.0.6 I think)
Excellent video. There is a lot in it in a very short time. Great. Will try.
I have my first Blynk test succesfully loaded yesterday. This will help me to progress further. Thanks
thanks
It is an excellent project, very complete! and above all by adding the IR it collaborates to not depend on the PC or the mobile. It was what I needed. Thank you very much brother!!
My board for now only has 4 relays, a dht , and last night I added a PWM control to drive some RGB strips. I have the ultrasonic sensor which I will be adding soon. Thanks again. Greetings from Santa Fe Argentina!!
thank you dear. So nice of you
How you are powering the esp through vin pin or cable also how much power you are supplying then what is the source of power like laptop or lithium battery
Great project Ahmad! I never thought of using an ultrasonic sensor for water level. That will work perfectly for me. I also need a sensor for checking water leakage such as under a sink.
Thank you.
Great 👍
Excellent project sir thanks for sharing such a nice work 😊
It's my pleasure
I really like your very useful project, thank you.!
Glad you like it!
Super project 👍🏼
Quick question: how do you do that with the animated connection and wiring diagram 🤔
merci beaucoup BOSS
Good 🙋♂️👍👍👍👍👍
thanks
Thankyou Sir for your Video
Most welcome
Awesome project sir..
Thank you! Cheers!
Hello Mr Ahmad! Great project here.
I just uploaded the IR code into my ESP32 but the serial monitor just keep generating something else and never responded to the presing of the remote. I'm using Bush TV remote or must it be that type (LED RGB) of remote?
Did you follow the suggestions I provided?
@@AhmadLogs yes I did to the letter
how would you able to add more datastreams in blynk console
Nice project sir.. 👍👍👍
Thanks
Hello,
I made the whole project but it has some problem after some minutes it starts turning on and off the relays itself, and some sensors like pir and ultrasonic doesnt work, what can be the problems .
Looking forward to your reply
Thank you for your amazing projects
Bro plz help can it be done by mobile phone using arduino droide
Interference from other devices or electrical noise can cause issues with your project. Make sure that your project is shielded from interference, and try moving it to a different location if possible.
make solid connection with quality wires
how about adding a gsm 800l. there isnt any wifi where i could use this great projekt.
great idea
Thank you and good job.
Ithink if we dont have any wi fi how we use sim800L for internet?
yes, it is possible
@@AhmadLogs may you tell me how ?regards
@@rampage_xdit lot of changes will be required in the code. I don't know how. but it is possible it required some time
very good
Thank you! Cheers!
in my blynk console i am unable to add more datastreams. it is asking upgraded version. can uh provide me alternate method or any cracked version of blynk
Good day, I was able to install version 2.0.9 and when i uploaded the "get ir remote Hex" but it was giving me the direct Number I press from 1-4, I got 1,2,3 and 4 directly and rspectively,is it supposed to be so?
no no its not bad. it is just fine. you just use the same in the code.
Sir, can you please upload the code? It will be very helpful for us beginners to understand.
Great project
♥♥♥
thanks
sir ... ESP-32 face reconization attandance systerm ... with googleseet and second project connct with web server ... mysqul detabce banaiye....
soon
ماشاء اللہ
thanks
Top ideia 👏
thanks
Sir plz help missing binary number before token "(" ye error bta raha hai kya karu
Can the sensor activate the relay, Sir for automatic and manual swicth,?🙏
no sensor will activate any relay. but you can activate a relay by making change in the code.
I'am beginner sir..i canot change the code.
@@diaryiklanlucudiarylancu8367 will try soon
Hello sir i can use esp32 no core
hi bro
What library you used
for what?
@@AhmadLogs for IRremote library can you send link you use in this project?
Shall i upload the same code to esp8266 board?
no
Bro how can i upload this program by using mobile phone plz help
not sure
working with esp
8266?
not sure
Hi sir
Notifications is free?
Thanks
Yes 100% free
Hi sir how can we upload these live data to our website live please help sir
Like publically on our website
to send live data to free website is not as easy. you need to buy premium plan for website to do live
Sir like getting widget data from blynk and live uploading to our website
@@balbirsinghheer1370 you can upload it to Firebase. What is the reason behind this? why you want it?
Sir actually I'm making my weather station for my village so i have to upload dht11 sensor readings to my own website and with if condition like when temperature is over 30C then readings should display high temperature on my own website so people can visit my website and check temperature (no weather station is currently in our village) so please help me sir i will be very thankful to you
add a nicer manual button, sir
Noted
@@AhmadLogs use wifi manager sir
In file included from c:\Users\User\Documents\Arduino\libraries\IRremote\src/IRremote.hpp:273:0,
from c:\Users\User\Documents\Arduino\libraries\IRremote\src/IRremote.h:10,
from F:\WIFI WATER LEVEL\ALL IN ONE SMART HOME\ALL_IN_ONE\ALL_IN_ONE.ino:115:
c:\Users\User\Documents\Arduino\libraries\IRremote\src/private/IRTimer.hpp:1373:50: error: missing binary operator before token "("
#if ESP_ARDUINO_VERSION < ESP_ARDUINO_VERSION_VAL(2, 0, 2)
^
exit status 1
Compilation error: exit status 1
error showing can you help me pls
just update your ir_remote library
It's still not working brother
@@Techno_lazy001 yes
It kept on giving me these:
"rst:0x10 (RTCWDT_RTC_RESET),boot:0x33 (SPI_FAST_FLASH_BOOT)
flash read err, 1000
ets_main.c 371
ets Jun 8 2016 00:22:57
rst:0x10 (RTCWDT_RTC_RESET),boot:0x33 (SPI_FAST_FLASH_BOOT)
flash read err, 1000
ets_main.c 371
ets Jun 8 2016 00:22:57
rst:0x10 (RTCWDT_RTC_RESET),boot:0x33 (SPI_FAST_FLASH_BOOT)
flash read err, 1000
ets_main.c 371
ets Jun 8 2016 00:22:57"
The error message you are encountering indicates that your ESP32 board is experiencing a reset due to the RTC watchdog timer (RTCWDT). This typically happens when the watchdog timer is not refreshed within its specified timeout period.
Here are a few steps you can try to troubleshoot and resolve the issue:
1. Verify the connections: Double-check the wiring connections between the ESP32 board and any peripheral devices or sensors. Ensure that all connections are secure and properly configured.
2. Update the firmware: Make sure you have the latest firmware installed on your ESP32 board. Check the official documentation or the manufacturer's website for any firmware updates or bug fixes that may address the issue you're facing.
I am not very excellent with embedded systems. I'm still a beginner and an enthusiast. These steps are somewhat very technical to understand fully. But I think I installed the latest ESP32 board (2.0.6 I think)
@@teachtechnorobotics It is fine if you are using the version 2.0.6. you just flash you esp32.