Building
Vložit
- čas přidán 10. 09. 2024
- More repair videos on the links below:
Instagram page:
/ valeramoskalu
Freightliner cabin repair Video nr.1 Wall outer panel removal:
• Freightliner cabin rep...
Freightliner cabin repair Video nr.2 Side panel instalation:
• Freightliner cabin rep...
Freightliner cabin repair Video nr.3 Side panel installation:
• Freightliner cabin rep...
Freightliner Cascadia cabin repair Video nr.4 Interior assembly:
• Freightliner Cascadia...
More repair videos on the links below:
Ambient air temperature sensor testing and repair Volvo VN
• Ambient air temperatur...
Honda GX 390 oil change pony motor:
• Video
Meritor power divider removal and disassembly:
• Meritor power divider ...
Peterbilt Brake Valve Replacement:
• Peterbilt Brake Valve ...
Meritor differential disassembly:
• Meritor differential d...
Meritor differential removal Volvo Truck:
• Meritor differential r...
Hendrickson wide bushings replacement:
• Hendrickson wide bushi...
Eaton transmission and clutch removal:
• Eaton transmission and...
Volvo D13 Radiator replacement:
• Volvo D13 Radiator rep...
Carrier reefer unit exhaust manifold replacement:
• Carrier reefer unit ex...
Rear axle differential repair Volvo Truck:
• Rear axle differential...
#Hendrickson suspension bushings replacement:
• #Hendrickson suspensio...
Hendrixon Vantraax frame brackets replacement:
• Hendrixon Vantraax fra...
Truck frame ramps for RGN trailer
• Truck frame ramps for ...
Volvo D13 coolant temperature sensor change:
• Volvo D13 coolant temp...
Eaton Fuller Transmission Air Module Replacement:
• Eaton Fuller Transmiss...
Wear hearing protection.... jeeez.
Yes, I didn’t wear it in the past and now I’m stuck with hearing aids.
You are right, I should!
What kind of drill bits do you use and for countersink? And what kind of flush flat head bolt?
What’s the purpose these?
could you make me a set for a 2004 freightliner? if possible with more of a curved arch and longer so they are further down. more like the murry style?
Where are you located if I need to get the same thing done to my Freightliner
Tacoma, Washington State!
I live in pdx and would love to have some of these. How long is the process and what do you charge? I have a 2005 freightliner Columbia daycare.
450$ it takes between 5 and 7 hours! We are located in Tacoma Wa!
I have seen a lot of Fifth Wheel ramps bolted on and leaning to the side. I have seen Fifth Wheel Ramps welded to the frame, that seem to hold up better. What's the thought on this?
As a mobile welder I have only done weld on ones. I buy 2.5 inch OD tubing .25 inch thick and cut it across like how they did. Plate the end and weld it right on the frame. I’ve never welded it that close to the fifth wheel before but it all depends what kind of trailer is being loaded. The guy $450 to do these what a steal. I charge $500+ and only use tubing
It's illegal to weld on semi truck frame. They may put you out of service for that !
Tony C. If it's illegal to weld on truck frames why do they allow stretching truck frames by welding a piece in the frame? It's done all of the time
@@delbutler885 I have no idea and this stupid rule about frame welding make no sense because welding is behind the fifth wheel l so doesn't affect anything anyway
Nice to see talented work just wondering why your workers don’t use safety glasses
😎
Wears hood to weld but grinds with no eye protection....classic
I've owned many trucks with these and this is not how there done. These are ok for avg trailer. But not for detachable neck. I've pull cozad trailers and have for 35 years.
What king of ramps were on your trucks?
Valeriu Moscalu We keep the width of ramp as wide as the outside of fifth wheel. So the guide rollers don't hit the fifth wheel. We extend tho the plate. Sometimes weld a small plate on fifth wheel. Bend the ramp at rear of frame down so rollers can pickup if there low. Your base mounts are great and very strong. I put my plate in center and take ramps to it. Guys in California leave them back and slide plates all the time I live in extreme weather and never slide plate and don't cross state lines so I don't really care what's on front axle
Thankyou for advice🙋🏻♂️ appreciate it Sir!!!