Great Video. The camera work is amazing and it was clear to see what you were doing. I plan on installing an intake system on my 2014 Lancer GT sometime soon. Still can't decide on this Injen one or the one from K&N.
I’m installing this on my lancer soon, but the issue I have is I have the 10mil screws for the bumper stripped off so it’s stuck there I’ll have to bypass this a certain way
YES, dont go over any flooded area, it will suck some water, also cover the wheelwell venting for those super heavy rain/ muddy time time there fore it doesnt clog the filter easily
@@pinipigcrunch ohh, because i reckon if you just change the pad filter to a K&N style (NOT CONE OR SHORT RAM) Just the pad from the oem to the K&N one it should be similar and safer and a bit cheaper, these cars aren’t 6-8cyl built Or especially turbocharged so i think unless you don’t either tune it or turbocharged it, it won’t be as beneficial I believe
Dam they don't make that easy! I had the 2008 Lancer GTS with the 2.0 it was alot easier. But there wasn't much you could do to make that engine faster.
![Mitsubishi Lancer 2.4L & 2.0L [#69-6544TS] Air Intake Installation](http://i.ytimg.com/vi/zqYtdNlo9QQ/mqdefault.jpg)
Great Video. The camera work is amazing and it was clear to see what you were doing. I plan on installing an intake system on my 2014 Lancer GT sometime soon. Still can't decide on this Injen one or the one from K&N.
So every time how to need service air filter..?
I’m installing this on my lancer soon, but the issue I have is I have the 10mil screws for the bumper stripped off so it’s stuck there I’ll have to bypass this a certain way
whats the volvo battery reconditioner do?
Does this fit a 2013 se lancer with 2.0L L4 engine?
where can I get a lift like that
Is it a lancer es or gts?
Anyone have a link to the intake system
i wonder how much more HP you've get with intake and exhaust system instaled
7hp
czcams.com/video/jGLNYWTQ6hc/video.htmlfeature=shared
Link plz
This the same setup for the ralliart turbo ?
No, its a different setup
Will this fit a 2017 Mitsubishi Lancer?
You have 17 me as well!!!!
Yup!
So you have to disassemble the whole bumper to clean the filter? Lol
Yes, or just remove the dirtguard (1 min job)
Will this effect going wet environments and mud / gravel type of areas?
YES, dont go over any flooded area, it will suck some water, also cover the wheelwell venting for those super heavy rain/ muddy time time there fore it doesnt clog the filter easily
@@pinipigcrunch ohh, because i reckon if you just change the pad filter to a K&N style (NOT CONE OR SHORT RAM) Just the pad from the oem to the K&N one it should be similar and safer and a bit cheaper, these cars aren’t 6-8cyl built Or especially turbocharged so i think unless you don’t either tune it or turbocharged it, it won’t be as beneficial I believe
Does it fit the 1.5 too??
czcams.com/video/jGLNYWTQ6hc/video.htmlfeature=shared
Dam they don't make that easy! I had the 2008 Lancer GTS with the 2.0 it was alot easier. But there wasn't much you could do to make that engine faster.
There’s a lot you can do to make the car faster lol most evo parts fit in the base model lancers
@@itstroy4145preach brother
did you tune your car for this intake??
No, but I did get check engine light on fuel/air too lean so it might be a good idea
@@justrandomcarsurbex3057 czcams.com/video/jGLNYWTQ6hc/video.htmlfeature=shared
@@justrandomcarsurbex3057Did you just reset the light?
do i literally have to move the tranny oil cooler just to install the cold air intake???
This is what im trying to find out because thats exactly where it is
@@AxelLopez-mx5ch you don’t have to, this is a different style of cold air intake, it’s placed differently
Niice but how can me buy this part
Just Google injen system for mitsubishi lancer