Zodiac MX6 Pool Vacuum Setup & Review (In-Ground Pool) *AMAZING*
Vložit
- čas přidán 20. 07. 2023
- Purchase your Zodiac MX6 Here: amzn.to/3uAsxEU
Hey everyone! I wanted to show off how to set up the Zodiac MX6 Automatic Suction-Side Pool Cleaner Vacuum for In-ground Pools. It's been absolutely amazing for me and I would highly recommend it. It's super simple to set up and use.
Comes with:
Zodiac MX6 Suction Cleaner
32' of Twist Lock Hose
Flow Regulator Valve
Various Valve Attachments
Directions:
1. Attach hoses together
2. Attach Flow Regulator Valve to hose
3. Attach hose to Pool Vacuum
4. Fill hose with water from pool jet
5. Attach valve end to skimmer (It should hold it in place with suction)
6. Turn flow to main drain down
7. Increase/decrease flow with main drain valve or flow regulator valve to allow MX6 Vac wheel to spin 10 times within 20-25 seconds - Jak na to + styl
Thank you for sharing your experience with this pool cleaner.
i am ordering one on Amazon, thank you.
Thank you!
How do you use it in above ground pool? I cant find a good way to hook it up in skimmer
my MX6 has been working reliably for about 2 years.
But I have now replaced the rubber bands and the "differential".
I have now come across the information that the number of revolutions at 10 revolutions should be 20 to 25 seconds.
What happens to my robot if it has 15 revolutions at 22 seconds instead of 10? So about 50% more. What could happen?
Thanks
Just got one. Generally happy though it doesn't get up and down my steps. My pool is curved both in section and plan. This does seem to affect it's climbing ability. I'm surprised at the claim that it's good on low-flow pumps. I find it needs plenty of sucking power.
If it’s scrubs the wall, how come wall look bad?
When you say that the speed will be too high and it sits upright is that like almost pop in Willy I have the MX eight I just purchased a six but I found it to be on the back side lift it up like it’s popping a Willy. I’ve had it for about six years, just replace the controllers but it’s still going in circles
Mine too and I can’t figure out hoe to adjust it.
I thought that you should not attach it directly to that port @2:30 without it going through a skimmer basket. I attach mine to a skimmer cover but I don't know if this is the right way.
You’re right. Much better to attach it to the basket.
@@StephenFixesThings Very useful video regardless I have an mx6 that came with the house when I bought it. It has been giving me problems I just replaced the gearbox. It works fine for 10 minutes but then it stops. Maybe it is not getting enough pressure.
Do you keep your MX6 in the pool on the days you're not using it? I just installed mine today.
I usually pool it out and set it to the side. If it’s really really hot outside it’s best to keep it in the shade when not using or the hose can weaken and crack.
So i take it you don't need a pool man if you have this cleaner? Also, can you tell me how the pump looks while running this unit. Does it rake on air or are you not supposed to see any air in the pump basket for it to be working properly.
I’ve had no air going into the pump at all. Runs the same way as if it wasn’t hooked up. No pool man for us!
@@StephenFixesThingsok I'm going to try to go without a pool man. Right now I'm getting air in my pump when I vacuum and I bleed the air out but it returns. I think I need to blow my vacuum lines out.
@@HRTsAFyrewe've never had one. We used a Hayward kreepy for years, but it finally died. We've been cleaning our's for a year with just a suction hose and woman power.. meaning I go in the pool and walk around the pool cleaning it myself. Well that got old. So we just purchased this MX6, put it in this morning. It's moving well, but pops wheelies where the water is coming back into the pool from the pump. Most of the debris in the bottom is gone already. Which is a miracle. I did notice while it's not flat, it still able to suction debris. Our's is also 16x32. We're going to need 2 more hoses, as it only came with enough for 30 ft.
If you adjust the grey part with red tab, will that make it move faster?
Help! Why does my sweeper pop back pn back tires? Also often turns in circles 3 or 4 times
Mine pops up on the back tires some but normally comes back down. You may want to lower the suction on it some. I believe it’s supposed to occasionally spin in circles to switch direction. Mine does that too.
@StephenFixesThings thank you for responding! After using a snap on water flow piece that goes through the skimmer the vacuum seems to work much better! There was too much water pressure it seems, now it's working well.
Mine does too!!! Just purchased the mx6 I was havng to be replacing parts too often
Hello I thnk I figured it out!! So last night I went out and if you have any house on the surface of the water …. Then there’s air! Need to disconnect hose but leave it submerged in the water to take out air! Do that through out the house needs to be submerged completely! Thnx let me know if it works!!
Awesome! That's great feedback. Thanks for the helpful info!@@robdawg700
On the pump , do i place pump on Backwash ?
Nope, keep it on your normal filter setting
you leave the pump on filter. I've found if I need extra power I can put on Bypass, but then only leaves and debris will be caught in the leaf trap.
It's not a weight, it's a floater
You’re absolutely right. Good call out.
It's not a weight. It's a float, that attempts to keep that part of the hose vertical and therefore the vacuum flush with the surface at the bottom of the pool. BTW it looks like you have a problem with algae in the bottom corners of your pool. You would normally connect hose ABOVE the basket and NOT remove it, or you're gonna have to clean the filter at your pump. Not the way. Think of a drowned rat, or big piece of debris being sucked all the way from your pool weir to the pump. A blockage somewhere en route is gonna ruin your day.
Good call. I'm going to work on getting an attachment to pull it directly to the trap.