how to Upgrade Power amplifier?
Vložit
- čas přidán 13. 11. 2018
- electronicshelpcare.net/micro...
/ pins
electronicshelpcare.net/2sc52...
/ electronics-help-care-...
/ electrohelpcare
/ @electronicshelpcare
#2sc5200#2sa1943#transistordiagram# - Věda a technologie
For the circuit diagram please visit here
shorturl.at/FNS56
Hi. By increasing the number of transistors, you will not get an increase in output power. The output power depends on the supply voltage and current, as well as the output voltage of the amplifier.
Sir...can you help me.im planing to change the transistor value.of my sakura AV3022 from 300 watts to 550 watts.thank you.
Lets suppose he has a 70-0-70v 30 ampere transformer. It can run the 2 transistor board and will not burn it. In this case increasing the number of transistors will help, provided the driver transistors gives enough current to the base of the 5200/1943 transistors.
ice cold hes using a very thin wire for the output it cant handle even a hundred watts how much more with a thousand.
Yea. He said 50V. So it's completely voltage limited into 8ohm load. Even with 4ohm, it's only 300W.
Well it would hav perfomed better if the extra transistors were driven by 5200 and 1943 from the driver board
😁 THANKYOU, FOR ALL THE HELP!!!!!!!
क्या बात है जबरदस्त ट्रिक
Thanks 👌👍
Looks good but I think the wire on the collectors is rather thin to carry 20 amps you may have a lot of voltage drop, It should be at least 1.5mm².You need also 20A secondary on transformer and a larger capacitor bank. I do not think now the base drive is enough for all those transistors.
yeah man but adding more transistor is not suitable for every driver ,
each driver carry its own min and max watt so you cant add more if driver made for only 300watt
There a few issues with this
Problem 1 transistors in this configuration have no voltage gain
2 the driving board will have a current limit which you just exceeded
3 the current capabilities of the transistor derates with voltage drop so increased supply voltage will decrease the availability of current without excessive heat
4 the voltage gain is likely from an op-amp that has a maximum voltage supply
Agree
Should be normal that the transistors have no voltage gain but current gain?
Please visit for amplifier circuit diagram
electronicshelpcare.net
la electrónica me encanta
Mantap 👍👍👍🙏🙏
Why add useless transistor? It doesn't mean more transistor = more power? You need to upgrade the power supply and some modifications to the driver stage for stable operation.
I've watched all of your video like this...and can you plsss test it..if it is really good?
Very good DEMO 👌👌 thanks brother
Gaurang DJ Sound ODHAV Ahmedabad Gujarat
Just sharing the heat, but the power output willnot increase. dangerous too for output transistor, you need to put base resistor each and so that driver transistor will not be overload.
I seriously suggest you buy a fan and set up some type of fume extractor because you are going to have problems with your breathing if you breathe in too much solder fumes
Vi um projeto igual a esse o seu ficou bem melhor e mais organizado resistente parabéns
I would like to see the output on an oscilloscope, a 10 KHz sine wave would show a huge amount of crossover distortion because there's no biasing network.
Good point. I set up XOD at 11kHz 2Vp-p👏✌️🦅
I used all resistance in 2watt rating as u told there .
Sir pls make video on yiroshi driver board
Makasih kak sangat detail tutorialnya
hi , thank you so much for this video, please i want use 4 or 5 transistor 2sc5200, what I do exactly, and thank you again
Wait till you try it before you thank him 😜🙂
In addition, in the previous stage, transistors (drivers) must have good cooling.
Bro please send the circuit diagram of mono 200watts and stereo 300watts amplifier based on 5200/1943 and 200 watts amplifier for TDA 7294 .plz reply.
So there’s a 8 transistor versus one , but the capacitors kept the same in the drive unit. Seems fishy to me that it’s just this easy ....
no in actual assemble there some of the parts i think 4 parts need to replace it, its a secret idea .
Thank u so much🔈🔉🔊
For 50V amp output you need 2.5 Ohms speakers to have 20A current. If speakers are only 4 Ohms, you get maximum 12.5A current and 625W power.
Actually way less than that, amplifiers are rated in RMS, so with 50 volts p-p at the output, you have really only 17.675 volts rms/4 ohms=4.42 amps X 17.675 volts= 78 watts RMS
tanks nice sipled mind
make a video calling him to listen to !!!
It doesn't work like you think. The current at base will be divide to other transistor so you decrese the performance.
It doesnt mean 50 x 20 = 1000 watts that your gonna get 1kw its more 900 watts or 850 cuz of the internal resistance of the transistors so if you want 1kw i recommend 75 0 75 volts 25 amps
y cuantos voltios recomiendas para 300 vatios RMS de potencia?
@@GamePlay-gz4ep Meu amplificador tem 250w e uso 63 volts. Talvez sirva para 300w.
Nice
no audio test?
olá vc pode passa para mim esta modificação deste amplificador ,se der obrigado ,gostei mesmo.
Very very very very very very good bhai
Good job 👍🏻👍🏻 🇮🇳 Kuki 14|08|2022
On porew amplifier you needest bigger ampere and tranzistor output its also need no modification of the original circuit driver resisotr. Power outage didoes clamp down to 4A menwelll power transformer CLIP dower so 4 tranzidstor output in 4 and 8 OHMS of 500W darlignton MOSFEPT cikruit.
It this circuit need dual power supply and the output rms power increases ????
Yeah Dual power suply (+) 55v ( - ) 55v and GND
dual and huge transformer ( more than 1000/1200 VA .)
how can you achieve higher wattage if you use same driver transistor, it could not drive those 16 transistors, the power output it should be in darlington pairs
50v wistand or not your board
cables demasiados finos, deben colocar calibres mas gruesos para que soporten tanta corriente.
nice video bro
Those heat sinks are not big enough for 1000W To get more power you need a higher voltage
+/- 70 volts min. you also have to drive the power transisters harder, more volts, heaver wire #12 or #10. There are more things that need to be done.
Nice video
Mene bnai thi ye pcb good sound
modul kit power socl 504 socl 506 👍👍👍 from indonesia JOSS
1000w on tight wires.
You must need fat wires
And just like that, you don't need to upgrade any of the supporting circuitry????
I wonder how long this will last?🤔
no need to upgrade the pre-amp, upgrading the main drive or power amp is enough.
बहुत सुंदर, आपका यह वीडियो देखकर एक बुधु से भी बुधु आदमी इंजीनियर बन जाए,
good night, how many volts does this audio card support?
Nice bro
Sir please show the performance 🙏
- предоконечные управляющие транзисторы как минимум надо на радиаторы установить.
hi sir..what kind of soldering iron you are using?
May i ask you.. Is that only one channel amplifier? How to put left and right speakers?
It's having heat up on 12-0-12 5amp only . What the problem it is . Heat sink also connected and good quality and quantity
Bro power output will be less
What is heating up? Transformer or transistors?
Check the OHMs of your speaker
with many pairs it improves the damping factor and the sound is more beautiful.
the improvement is more evident by doubling the power capacitors.
is it making sound good , after adding more transistor ,
i have one question , since my system is for 200watt and there are 4 transistor ok
so i dont mean to increase the i am not going to increase power
only if i added 6 transistor means 4+2=6
then will it increase the sound qaulity , i dont care it is ok if i am getting 200watt only from 6 or 8 transistor ok only thing is i want better saund qaulity
Please guide me about Amplifier design softwere and
Good video
Daisy chained collectors ! Ha ha ha, bloody hilarious !
I would like to hear about the amplifier when it does not give any noise
Hi
I just build the same circuit based on the same diagram but I have a problem. I used the same components except the BD139 becouse I had only BD140 in stock.
Could this be the reason that at low volume levels the amp distorts but at higher levels its playing fine?
Please let me know if you have something in mind about that. Thanks
Please visit for circuit diagram
www.pinterest.com/electrohelpcare/pins/
Can i use this amplifier for PA Systems like outdoor program?
Yes you can
Hi. Great video. I have a question: It's possible to decrease power in a power audio amplifier, doing the opposite? Might have some troubles if I remove some pairs of transistors a in power monoblock to decrease power?
How buy this circuit board ...... Please reply
Helo bro plz tell me why use .47 ohm resistance in between emter and speaker
Amo eletronica
Hello Sir Goodday!Which one is better toshiba transistor or njw transistor?
Brother ! Adding more transistor how i can increase circuit voltage . like 60-0-60 or 75-0-75 ac from transformer
Nice vaia
Pero si el ingeniero hizo la placa para esos dos transistores. Como le vas a sumar más carga y voltajes?? Tenés que hacer todo de cero.adelas esos cablecitos no soportan la carga de 1000watt .se le ponen cables pijudos de 2 milímetros y tipo alambre para que no hagan resistencia en su trayecto
Phuhghggggje8777u788+09uhnnbj poi+00009999iiiiiiygyhjhuujnmk.
oh super.. 1000W amplifier can use 50 0 50 V 20A Transformer... its up to 20 kilogram waight
Hlo bro I've made this small mono circuit but 1943 has much heating on slower volume. And sound also didn't be strengthened as volume turned up. Help plz
Show us the drawing of the circuit..
It sounds like you have put components in the wrong way ie small input pair or not correctly set up the biasing..
Because this is not correct. This is not the way to increase power. Increase heat sure but you will need to look for another video that correctly shows how to achieve the goal that this video is saying it is achieving
¿Y la fuente de poder? De algún lado deben salir esos ampers de más. No será de la fuente que ya tenía...
Hi sir, can you share your power amp driver pcb layout and component placement guide please
electronicshelpcare.com/transistor-circuit-diagram-2sa1943-2sc5200-2/
@@electronicshelpcare thanks a lot sir godbless
link open kiyu nahi ho raha sir
El. Siguiente. Saludos
do you have a video to test the sound
👍👍👍
i think this circuit can use maximum 35-0-35 ac voltage. is this correct ?
i have a question how low it can handle term of impedance of the load.
he doesn't increase the voltage but the ampere is high if he is correct
can he go at .25 ohms like 2 dual voice coil 1 ohms each coil
note speaker do not have steady resistance it can go higher or lower when playing
nice video
Can you check the power supply and sound quality of your upgrade amplifier?
Hlo plz help and answer all the problems
Ciao...ho i finali e tutto quanto il resto ed un alimentatore switching da 500 wstt a 65 volt duale...come posso fare per poterlo usare von questo circuito riducendo il numero di finali?
you make that broad how many watts?
i have my 200+200 watt board but after seeing you, your board is made for that much watt, man i can see each resistor is 2 or 1 watt ,
but in my system there small watt resistense and also only three big transistor and remaining 7 transistor are so small and you have 7 big size , and also the size of capacitor is also big
so i know you cant add more transistor in any board untill and unless we know the min and max watt capabilities of that particular board with input volt and amp
He cannot achieve that desired power, because he uses small wires and the driver is original not an upgrade.
bro kisi bhi board me kar sakte hai kya extra mosfet add
Good
Sube de voltaje.. muestra el vídeo como funciona..de sonido..
Thank you sir
Top
Thanks
Whats the reason for using 2sc5200 and 2sa1943? Why not use only 2sc5200 x 2 or 2sa1943 x 2?
why you joined two output of the transistor using 0.22 ohm resistor? (NPN & PNP) positive & negative together....??? its short circuit bro. i don"t understand.!!!
Can I use any paper when separating heatsink and transistors?
Please visit for circuit diagram
www.pinterest.com/electrohelpcare/pins/
have you measured the current on the driver transistors?
Luk Luk. - your question is right. The more adding output transistor, the more bias decrease given by the only one driver transistor..
@@shiernanpapin85 can you explain what bias is and what dco is
Bhai amplifier ke fen Ko ripear hota hai kya or kese
SUPER
Why you dont use Resistor for basis of transistor??
In put koto volt DC
nice
MEU AMIGO. VOCÊ ESTAVA INDO BEM. AI VOCÊ REROLVEU POR UMA PLACA. QUE NÃO SABEMOS ONDE ENCONTRAR. AI COMPLICOU TUDO. E VOCÊ NEM TERMINOU O PROJETO. METEU OS PÉS PELAS MÃOS E CAGOU TUDO. INFELIZMENTE É DESLIKE.
A placa é um amplificador de 100w, o que ele está fazendo é um upgrade para 1000w acrescentado mais transistores (leia o título do vídeo), essa placa encontra-se até no mercado livre ou nesses sites chineses de compras. O projeto está finalizado, é só colocar a alimentação e falante.
Super