GoPro BONES + Gep RC CineLOG 30 - Best new Quad for GoPro?

Sdílet
Vložit
  • čas přidán 13. 09. 2024

Komentáře • 18

  • @M4tactics
    @M4tactics Před 2 lety +1

    Thanks brother Thomas. Killer videos as always

    • @TG_Shreds
      @TG_Shreds  Před 2 lety

      Thanks dude! good to hear from you James!

  • @josephoconnor8763
    @josephoconnor8763 Před rokem +1

    I see the CineLog30 on Amazon. What is the difference between the PNB and TBS Nano RX editions? Does this have any impact on GoPro compatibility?

    • @TG_Shreds
      @TG_Shreds  Před rokem

      The difference between PNB and TBS is what receiver protocol you were using. PNB means that it doesn’t come with a receiver, and TBS crossfire is a type of receiver.. what controller/transmitter are you using? Will help determine what receiver protocol to use. They do not have any impact on GoPro compatibility.

    • @josephoconnor8763
      @josephoconnor8763 Před rokem

      @@TG_Shreds What do you use for a controler?

    • @TG_Shreds
      @TG_Shreds  Před rokem

      @@josephoconnor8763 I am using the Radiomaster TX16s with an external crossfire module

  • @Pict8kr17
    @Pict8kr17 Před 2 lety +1

    Great video! I have the 25 and looking to pick up the 30 for my hero bones. I feel it is a bit heavy for the 25. Any advice on tune? I’ll be doing mostly cinematic video tours outdoors and indoors if possible.

    • @TG_Shreds
      @TG_Shreds  Před 2 lety +1

      Great question, I tuned my rates so that my throttle isn't as responsive. I am not an expert on tuning and don't feel conformable recommending any tune settings. There are some great tutorials on CZcams for cinematic rates. I would give those a watch.

  • @bearer0975
    @bearer0975 Před rokem +1

    So I am trying to do this now. The voltage at the plug going from the cinelog 30 into the gopro is direct 4s battery voltage. can a gopro take 16.8 V?

    • @TG_Shreds
      @TG_Shreds  Před rokem +1

      Yes. I looked online and it looks like bones takes 5v-27v

    • @bearer0975
      @bearer0975 Před rokem +1

      @@TG_Shreds Thanks It is working fine now.

  • @yashalarif8342
    @yashalarif8342 Před 2 lety

    how to downstream the video with gopro hero 10 black bones

  • @officedroneescapes4874
    @officedroneescapes4874 Před 2 lety +1

    Nice video. Does it feel heavy in flight with the GoPro on? Could you still do light freestyle with the GoPro on? I fly a Cinelog30 with a Caddx Peanut. I'm considering an upgrade to the Bones but I'm concerned about the weight affecting flight performance; it still feels pretty light in the air with the Peanut(~30grams). Also what was your flight time with that 650 and the Bones? Thanks!

    • @TG_Shreds
      @TG_Shreds  Před 2 lety

      I personally don't think it feels heavy with the Bones attached. I can still whip it around and freestyle with confidence. That being said, I do notice a slight difference in performance when it's attached, but it's to be expected. I think you can definitely freestyle with it, but it will be nothing compared to a 5 inch ripping the same freestyle lines. I am averaging just over 3 minutes for cruising and just under 3 minutes when flying more aggressive with the 650s.

  • @flyfastmedia
    @flyfastmedia Před 2 lety +1

    How hot do your motors get? Do they at all? My cini 25 with this is scalding hot lol even with 300mah 4s

    • @TG_Shreds
      @TG_Shreds  Před 2 lety +2

      The motors get warm but not hot. I can touch them with my bear and after flight. It’s typically the VTX that gets the hottest for me. I have used a few different batteries but my favorite is 4S 550 mAh

  • @frangeech
    @frangeech Před 2 lety

    What are you getting for flight times on this setup?

  • @crazy3rdgen
    @crazy3rdgen Před 2 lety

    My cinelog 30 felt very nose heavy with a bones on it