I have a 2009 traverse that had a po300 random misfire code. There was no power on the pink/black power wires at the even bank coils. The problem was the same one you described. I disassembled the fuse panel and found some corrosion on the terminals. I cleaned everything up, reassembled the panel and all is well. Hope this helps someone.
I'll keep that mind thanks. Hey got a question real quick. What did you use, or do to clear up the headlight assemblies? Got a Traverse also with the the same problem.
2011 Chevy Traverse 2 wheel drive starts but shuts off after maybe 1 min replaced crankshaft sensor as indicated on reader but still shuts off what could be the cause😢
Sorry that your car is having this issue but it could be that it needs a tune up or as bad as it need needs a new timing chain this car are known to have that issue. Good luck
i need some assistance…. i got p0304…. cylinder 4….. changed out spark plugs…. ignition coils since it has 200k miles, did a carbon clean up around the valves, basiclaly any maintenance that i needed and still has the code any suggestions? and it’s a 2017 chevy traverse 3.6L I have also switched out the ignition coils and ruled out defective ignition coils
Hey buddy sometimes changing the fluid and adding transmission additives helps it all depends what damage the transmission has also replacing the or cleaning the shift solenoids. good luck
I have a 2016 Chevy Traverse Lt AWD change d right front strut now I have service traction control and stability light on dashboard any help would be appreciated ty
You know I went to the shop me and my husband we got all that did they even scrape all that carbon that was built up still as of right now I engine light comes on and off and the shop now this was the dealer saying that we probably have to come back and get the cylinder 2 fix is crazy we did all that now don't get me wrong the car drive much better than it did real smooth but it's crazy cuz it's like we took it to two different shots nobody to know why the light was still on and you did all that engine flush change the oil fuel injectors all that
Okay now I guess we going to try to get the cylinder to fix and the dealer Chevy dealer said that's like $3,300 something dollars right there but also why that check engine light on the parking brake and the steering something about the steering comes on every since this started happening all them two lights come on and then the engine light started flashing but the light go away the engine light just be on
At first, I tighten up the bolts to verify that was the problem and it fixed it, then after I removed it to replace the motor mount under it. I have a video of that as well. thanks. @@tuckerbingo2491
Thank you bro , you saved me a lot of money and time.
Im glad my video helped you ☺️
I have a 2009 traverse that had a po300 random misfire code. There was no power on the pink/black power wires at the even bank coils. The problem was the same one you described. I disassembled the fuse panel and found some corrosion on the terminals. I cleaned everything up, reassembled the panel and all is well. Hope this helps someone.
Thats a great add on to this video, thank you!
Thank you Trent
I'll keep that mind thanks. Hey got a question real quick. What did you use, or do to clear up the headlight assemblies? Got a Traverse also with the the same problem.
I'll live you the link to the video where I show what I use, hope it helps thanks czcams.com/video/NEXIwC7oIuI/video.htmlsi=p9A3HP8JhA-HCUxs
Ok thanks!@edwinmartinez1756
2011 Chevy Traverse 2 wheel drive starts but shuts off after maybe 1 min replaced crankshaft sensor as indicated on reader but still shuts off what could be the cause😢
Sorry that your car is having this issue but it could be that it needs a tune up or as bad as it need needs a new timing chain this car are known to have that issue. Good luck
Thanks
your very welcome
i need some assistance…. i got p0304…. cylinder 4….. changed out spark plugs…. ignition coils since it has 200k miles, did a carbon clean up around the valves, basiclaly any maintenance that i needed and still has the code any suggestions? and it’s a 2017 chevy traverse 3.6L I have also switched out the ignition coils and ruled out defective ignition coils
I would do a compression test to see if that's the problem. did you do it yet? and did you try what I said in my video.
Clean your throttle body or replace it
Cleaned it @@kreshapier6471
If your top motor mount is out high likely front motor mount is out every time oil filter change oil get in it and ruins the rubber.
100% agree 💪🏻
Anyone has advice. 2012 chevy traverse thans slip.. would thans flushing help let me know ty
Hey buddy sometimes changing the fluid and adding transmission additives helps it all depends what damage the transmission has also replacing the or cleaning the shift solenoids. good luck
I have a 2016 Chevy Traverse Lt AWD change d right front strut now I have service traction control and stability light on dashboard any help would be appreciated ty
Check the wheel speed sensor wire on that side, maybe it got damaged.
Can somsome help me out is the front 3 1,3,5
Hey so the front cylinder are 2,4,6 hopefully this helps.
You know I went to the shop me and my husband we got all that did they even scrape all that carbon that was built up still as of right now I engine light comes on and off and the shop now this was the dealer saying that we probably have to come back and get the cylinder 2 fix is crazy we did all that now don't get me wrong the car drive much better than it did real smooth but it's crazy cuz it's like we took it to two different shots nobody to know why the light was still on and you did all that engine flush change the oil fuel injectors all that
Yeah, I did a lot of service to the engine and it turned out to be was the connection under the fuse box. that has to be tight.
Okay now I guess we going to try to get the cylinder to fix and the dealer Chevy dealer said that's like $3,300 something dollars right there but also why that check engine light on the parking brake and the steering something about the steering comes on every since this started happening all them two lights come on and then the engine light started flashing but the light go away the engine light just be on
@@edwinmartinez1756so did you remove the fuse box or just tighten bolts?
At first, I tighten up the bolts to verify that was the problem and it fixed it, then after I removed it to replace the motor mount under it. I have a video of that as well. thanks. @@tuckerbingo2491
Did you checked for loose connection on the fuse box like I explained in my video?@@nastassiabills5643