Amazing BC547 and 555 IC led chaser
Vložit
- čas přidán 26. 08. 2024
- Amazing BC547 and 555 IC led chaser
• Amazing BC547 and 555 ...
#Amazing BC547 led chaser # 555 IC led chaser #Amazing BC547 and 555 IC led chaser
Like Share & Subscribe Please Thanks All
Speed control 👍
Ok got it. Change both caps to 220uf 10v works great !!! This solves last led being dim, sequence is speeded just a little bit by cap on timer. paly around with the caps to get flash speed you want. Also you can discard the 4007 diode. Works fine without it.
Прекрасное видио. Спасибо! 👍👍👍👍👍
Навесная схема бегущих огней на 5-ти транзисторах. Набор деталей почти минимальный!!!
Very very nice
Good
Best offluck
احسنت تقسيم التيار كان منتظم ابدعت فى التصميم ولاكن انت انسيت حجه وفيه فكره جديدا ولى هيه التصميم والاطار وبداع فى تقسم الايظاه وهكى المقطع يخد وقت واكثر مشاهده اعجبنى
Nice. Your initial cascading circuit reminds me of something I designed on a bar napkin at 2 AM many years ago. My circuit had a different purpose and it was critical that it be integrated with a larger circuit by 8 AM. Fun memories.
Another good idea would be if only one LED would switch on for a second, then it switches off and the next starts...and so on. Great work there!
The 555 timer could run slower with a larger value capacitor. With 1/2 Watt resistors and RED LEDs you could fashion a car turn signal.
Aetila Look at the CD4017 chip.
Use variable resistor to controll chasing speed of led
Mạch này tui học rồi, dễ làm lắm
Neu minh su dung 100 hay 2_300 led thi sao,dau ss duoc k nhi
@@TaiNguyen-wj1fx xài cách khác, nội mà mắc mấy con đó chắc mua cho khỏe
Điện 12v khi qua ic 555 chỉ cho ra khoảng 5v hay 6v gì đó thui
@@tranvanquy6528 xài áp dc 3 _5 v à, đâu ai cấp 12 xì khói luôn sao
I love Your "printed circuit board free" construction.
LivingCoolness That’s called “point to point” construction.
'
good nice LED project...
try add use a speed control from slow to fast
Buenas noches amigo. Excelente trabajo. Tengo una pregunta. Me soporta tiras led de 30 CM aproximadamente a 12vcc?
Sir please mention all components in the comment. It's really amazing video!
Ppl really need to get in to small ic I can make one strobe, zig zag, flicker or solid on a board smaller Than that 9v battery and run off 3v . Programmable as well. What I started doing years ago was when I found something that interests me I'd buy two of the items one I took apart and learned from and a lot of times I do have to ask someone who knows, trial and error. The 555 is cool but way to much work to many parts and room taken up. I started with stuff like this and by no means am I kicking it. It's a good learning experience and circuit. But wouldn't you like to build the same or more advanced the size of that 9v and a whole lot less parts? Good job on the circuit and it is important to learn and teach. No disrespect intended.
Good job dear.
Can we increase the numbers of led?
Can we control the chasing speed of led?
Good project all the time. &very very clear.... Thanks
Last led dim but works. I am still tinkering with it. If solved I will post resolution.
Estaría bueno que dejes la lista de materiales que usas .
very good，If you can provide a formula to change the flashing time of the lamp is the best
Change the 555 capacitor to find the speed you want.
Easy, you go and farm your land and leave electronics to the clever one's.
Muy bonito el circuito, pero..... por diossss Aprender a soldar que me duelen las retinas de los hojos al ver la tecnica que usais
A mí me duelen las retinas al ver como escribiste "hojos", todos tienen sus defectos, antes de hacer el comentario mejor subí un vídeo explicando cómo utilizar la soldadora y el estaño...
Big thanks, good idea, спасибо!😉
Excelente, gostei muito.
Obrigado pelo exemplar.
P
Great Vidio...
Thà dùng thanh ghi dịch đỡ tốn linh kiện hơn
Хорошее изобретение, можете подсказать нужны моргалки на 24v. На прицеп,а то устал покупать, плафоны есть
Wow
Спасибо! Очень доходчиво и всё просто! Thank you!
Ok
Parabéns pelo vídeo muito bom já vou me inscrever
Era isso que estava procurando! Parabéns e obrigado!
Cara vc sabe que parte só circuito da pra usar um potenciômetro?
Прикольная схема, но желаю автору поскорее узнать про существование флюса и научиться паять красиво и надёжно
Good idea
¿Puedes hacer un amplificador de 30 Watts? (Can you make a 30 Watt amplifier?)
Interesting component change would be to switch out one of the resistors on the 555 to a variable pot and you can change the speed of the LED's. Say to 50K. experiment a little bit.
Excellent, I’ve wanting to do this for a long time. Thank you.
Remove the 555, reduce capacitor of the transistor for 50 or 100uF use audio signal and have VU
Hi Sir, good tutorial, so now, how to do if you need to make leds flashing every 60 minutes?
Olá amigo, boa tarde! Se eu fazer esse pisca, da para fazer piscar mais rápido ou não? Pq eu quero fazer para usar como seta na bike! Valeu
Tenta diminuir a capacidade do capacitor, pode ser que funcione.
Sir please what is the name of the song used firstly
Kya hum is ki speed ko variable bna sakty hain?
Reply please
Я поворотник увидел, кто что?
please , how can the diod discharge the capacitor , theoriquely impssible to discharge the capacitor throught the diod like this ??
Vary vary nice video
How to control led running speed.anyway great project.
Sir chashar se kitni led bulb Chala sakte Hain
great sir....!!! If I want use 5 Volt DC, what can i do?
pregunto.... como se puede hacer ese mismo efecto pero de derecha a izquierda y viceversa en un solo circuito y si es posible con control de velocidad...
Está mal, en la colocación del diodo rectificador pone en pantalla el signo de positivo en el lado negativo (cátodo). Haz bien el vídeo y sorprende con tu circuito.
Great! You almost made it by selling this to Audi-the most profitable lamp factory
How long can a chain be built? with power 12v
The timing will change with longer chain. Just change values of caps for drain.
Take me also in this job.
Music ???
Excelente trabajo. ¿ a que voltaje esta conectado?
What is this used for?
Sir how to slow 40 second delay glow time please make video 👍
Good proyect.. thanks gracias
Good video that's help me!
Очень нужная в хозяйстве вещь.
Особенно в прихожей, сделал две шт, не знаю как без этого раньше жил
another project with the Ci 555 ... very cool, I would like to make one, but I can not find all the components!
Try Amazon they have EVERYTHING I get all my electrisions from Amazon
Not to be rude, but there is such a thing as Flux for soldering. Really helps out.
Yakov Yudin flux is in the solder.
@@vpistilli It isnt the same. Trust me.
@@RusoHacker007 So you are telling me that all those solder joints I made since my first job in 1965 until now are no good? All my employers would not agree with you. Yes, there are times that putting flux on maybe a piece of brass that is not tinned is necessary, but where he is soldering these components together, is OK just to use the solder with flux in it. The components he is soldering are pre-tinned. The flux in the solder is sufficient.
@@vpistilli Sounds good. Didnt mean to upset you. I just found whether the solder has flux or not, using soldering flux makes the solder flow a lot better.
Kalo bikin jangan menggunakan batu batre.usahakan tegangan ac220 atau DC 24 vol /12 vol baru Berman FA at
Please explain how it works.
Para 3.7 vol??? por ejemplo con la pila 18650? sabrás? Saludos.
great sir i like that
agr ham is ko 12v 3amp pr chlaa chahy to kysy chlay
Красавэлло! Thank you!!!!!!
Hum isme aur kitne led badha sakte hain or kaise plz reply
タイマーIC 555
懐かしいですね
otimo video parabens
Hasta cuantos LED'S soporta la instalación gracias y esta genial
Depende de la corriente de la pila supongo
Backsound?
Hello! Do you have the circuit in proteus?
Hello NE555N
NE555P
NE55555 dip 8
LM555
KA555
is it all the same? help? is there any difference?
necesito uno que esten todas prendidas y se vallan apagando de una por una podras hacer un tutorial
Невероятно полезная вещь. Но уж больно громоздкая ёлочная гирлянда. особенно кусачки для ногтей хороши. Для съёмки хоть в долг у кого взял бы нормальный инструмент.
Bang saya mau tanya, resistor yang sudah tercantum ke lampu LED itu, berapa OHM ? Tolong balas saya 🙏 saya menunggu.
The bulk charger have the same circuit, how do you mesuring the leds? How do you know that they are right?
Absolutely beautiful project and execution! Very inspiring.
Good
i want to use 4 led for per channel but end channel is dim light
What is value of Resistor you last connect to IC 555 pin number 6 and 7.
Very nice idea. Thank you my friend. 🌷🌷
Thank you Dear
Muito bom. Perfeito.
Jhalar light ko running light light kaise banaye asaan tarika
10K and 220ohm resistance 1/4watts hay ya 1/2watts?
how about 24v LED light can it run like that?
I think this is top secret. ;-)
Nice
Thank you Dear
merci
लेटरको भि जला सकते है क्या ? जैसे कि एक लेटर मे ३० लिड लगते है और एसा ५ लेटर है कैसे करें ?
How if use led strip ?
Hey, great scheme. what value of the second capacitor which is sealed for 555 chips?
ok. bad watched a video.
It is 100uf 50v
Las soldaduras! Jajajaja
Super, GOD bless you
Hola puedo preguntar:...Para que puede servir un juego de luces así? Porfi...no me da la cabeza
Enrique, lo puedes usar para el stop de un coche , digamos que en una barrita de aluminio pones 10 leds, 5 hacia la derecha y 5 hacia la izquierda partiendo del centro, entonces al alimentarlo, se va a ver un efecto llamativo, es decir, los leds se van a ir encendiendo progresivamente del centro hacia los lados, cada ves que pises el freno del coche, y la otra opción es que puedes usarlo haciendo unas letras de algún negocio etc etc
Para la bici
Video Subtitle: "How Not to Solder".
Hi,can i use 10 led for same extension .
Hello ! Can you send the circuit design? thank you!
Makasi infonya
hi friends! Technology se related videos dekhane k liye hamare channel ko subscribe katen...
Can I have circuit diagram for this